Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  cap_prctl: don't set error to 0 at 'no_change'

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  igb: remove sysfs entry that was used to set the number of vfs
  igbvf: add new driver to support 82576 virtual functions
  drivers/net/eql.c: Fix a dev leakage.
  niu: Fix unused variable warning.
  r6040: set MODULE_VERSION
  bnx2: Don't use reserved names
  FEC driver: add missing #endif
  niu: Fix error handling
  mv643xx_eth: don't reset the rx coal timer on interface up
  smsc911x: correct debugging message on mii read timeout
  ethoc: fix library build errors
  netfilter: ctnetlink: fix regression in expectation handling
  netfilter: fix selection of "LED" target in netfilter
  netfilter: ip6tables regression fix

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc: Hook up sys_preadv and sys_pwritev
  sparc64: add_node_ranges() must be __init
  serial: sunsu: sunsu_kbd_ms_init needs to be __devinit
  sparc: Fix section mismatch warnings in cs4231 sound driver.
  sparc64: Fix section mismatch warnings in PCI controller drivers.
  sparc64: Fix section mismatch warnings in power driver.
  sparc64: get_cells() can't be marked __init

* 'ext3-latency-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext3: Try to avoid starting a transaction in writepage for data=writepage
  block_write_full_page: switch synchronous writes to use WRITE_SYNC_PLUG

One-liner: capsh --print is broken without this patch.

In certain cases, cap_prctl returns error > 0 for success.  However,
the 'no_change' label was always setting error to 0.  As a result,
for example, 'prctl(CAP_BSET_READ, N)' would always return 0.
It should return 1 if a process has N in its bounding set (as
by default it does).

I'm keeping the no_change label even though it's now functionally
the same as 'error'.
Signed-off-by: NSerge Hallyn <serue@us.ibm.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

This patch removes the sysfs entry num_vfs which was added to support
enabling pci virtual functions for 82576.

To prevent VFs from loading automatically a module parameter "max_vfs" was
added so that the number of VFs per PF can be limited.  This is especially
useful when 4 or more 82576 ports are on the system because otherwise to
load all VFs would result in 8 interface per physical port.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds an igbvf driver to handle virtual functions provided by the
igb driver when SR-IOV has been enabled.  A virtual function is a
lightweight pci-e function that supports a single queue and shares
resources with the 82576 physical function contained within the igb
driver.

To spawn virtual functions from the igb driver all that is needed is to
enable CONFIG_PCI_IOV and have an 82576 Ethernet adapter on a system that
supports SR-IOV in the BIOS.  The virtual functions will appear after the
interface is loaded.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After dev_get_by_name(), we should follow a dev_put().
Signed-off-by: NYang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't strain gcc's tiny mind.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets MODULE_VERSION in order to help users track
changes to this module.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mips identifier is reserved by gcc on mips plattforms. Don't use it
in the code.
Signed-off-by: NBastian Blank <waldi@debian.org>
Tested-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

platform_device_register_simple() returns ERR_PTR(), not NULL, if an error 
occurs.

Found by smatch (http://repo.or.cz/w/smatch.git).  Compile tested.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move SDMA configuration from interface up to port probe, to prevent
overwriting the receive coalescing timer value on interface up.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the warning printed when a mii READ times out currently says "Timed out
waiting for MII write to finish".  This patch corrects this.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethoc indirectly uses crc32_le() and bitrev32(), so select
those library functions to be built.

drivers/built-in.o: In function `ethoc_set_multicast_list':
ethoc.c:(.text+0x6226f): undefined reference to `crc32_le'
ethoc.c:(.text+0x62276): undefined reference to `bitrev32'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] wire up preadv/pwritev system calls

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  x86 ACPI: Add support for Always Running APIC timer
  ACPI x86: Make aperf/mperf MSR access in acpi_cpufreq read_only
  ACPI x86: Cleanup acpi_cpufreq structures related to aperf/mperf
  ACPICA: delete check for AML access to port 0x81-83
  ACPI: WMI: use .notify method instead of installing handler directly
  sony-laptop: use .notify method instead of installing handler directly
  panasonic-laptop: use .notify method instead of installing handler directly
  fujitsu-laptop: use .notify method instead of installing hotkey handler directly
  fujitsu-laptop: use .notify method instead of installing handler directly
  ACPI: video: use .notify method instead of installing handler directly
  ACPI: thermal: use .notify method instead of installing handler directly
  ACPI battery: fix async boot oops
  ACPI: delete acpi_device.g_list
  NULL noise: drivers/platform/x86/panasonic-laptop.c
  ACPI: cpufreq: remove dupilcated #include
  ACPI: Adjust Kelvin offset to match local implementation
  ACPI: convert acpi_device_lock spinlock to mutex

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5446/1: ohci-at91: Limit vbus_pin assignment to the size of the array
  [ARM] 5445/1: AT91: Remove flexible array from USBH platform data
  [ARM] 5447/1: Add SZ_32K
  [ARM] omap: fix omap1 clock usecount decrement bug
  [ARM] pxa: register AC97 controller devices
  [ARM] pxa/csb701: do not register devices on non-csb726 boads
  [ARM] pxa/colibri: get rid of set_irq_type()
  [ARM] pxa/colibri: provide MAC address from ATAG_SERIAL
  [ARM] pxa/cm-x2xx: fix ucb1400 not being registered
  [ARM] pxa: Add support for suspend on PalmTX, T5 and LD
  [ARM] pxa: PalmTE2 support for battery, UDC, IrDA and backlight
  [ARM] pxa: Palm Tungsten E2 basic support
  [ARM] pxa/em-x270: add libertas device registration
  [ARM] pxa/magician: Enable bq24022 regulator for gpio_vbus and pda_power

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  mmc_spi: support for non-byte-aligned cards
  omap_hsmmc: Do not expect cmd/data to be non-null when CC/TC occurs
  mmc: Fix compile for omap_hsmmc.c
  mmc_spi: convert timeout handling to jiffies and avoid busy waiting
  mmc_spi: do not check CID and CSD blocks with CRC16
  omap_hsmmc: Flush posted write to IRQ
  New mail address for Pierre Ossman
  imxmmc: move RSSR BLR
  imxmmc: init-exit rework
  mmc: Accept EXT_CSD rev 1.3 since it is backwards compatible with 1.2

Thou shalt remember to use 'git add' or errors shall be visited on your
downloads and there shall be wrath from on list and much gnashing of teeth.

Thou shalt remember to use git status or there shall be catcalls and much
embarrasment shall come to pass.
Signed-off-by: NAlan "I'm hiding" Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Gerd Hoffmann added these to Linux.  Let ia64 use them.
Signed-off-by: NTony Luck <tony.luck@intel.com>

Currently, the vbus_pin assignment loop is limited by the value of the "ports"
variable in the platform data.  Now that the vbus_pin array is no longer
flexible, we can use its actual size.
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The flexible array in the USBH platform data is not safe to copy.  The
compiler will not allocate any extra memory for the non-init platform
data structure (in the *_devices.c files) since it isn't given any
defaults at compile time.  When the probe function attempts to address
that array, it will actually attempt to access data in an adjacent
structure.

Since there are currently no (known) implementations of the at91 USBH
IP with more than 2 vbus pins, I am capping the value at 2.  If somebody
tries to assign more, then the compiler will produce a warning.
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds a SZ_32K define to the available sizes. I need it for an
upcoming platform support.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

A very large subset of SD cards in the market send their
responses and data non-byte-aligned. So add logic to the
mmc spi driver to handle this mess.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

With spurious interrupt cmd can be null even when we have CC
set in irq status.

Fixes: NB#106295 - prevent potential kernel crash in the MMC driver
Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

This fixes the issue noted by Russell King:

drivers/mmc/host/omap_hsmmc.c: In function 'mmc_omap_xfer_done':
drivers/mmc/host/omap_hsmmc.c:301: error: implicit declaration of function 'mmc_omap_fclk_lazy_disable'

This got broken by 4a694dc9.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

SD/MMC card timeouts can be very high. So avoid busy-waiting,
using the scheduler. Calculate all timeouts in jiffies units,
because this will give us the correct sign when to involve
the scheduler.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Some cards are not able to calculate a valid CRC16 value
for CID and CSD reads (CRC for 512 byte data blocks is OK).
By moving the CRC enable after the read of CID and CSD, these
cards can be used. This patch was tested with a faulty 8 GByte
takeMS Class 6 SDHC card. This patch was suggested by
Pierre Ossman.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Spurious IRQs seen on MMC after 2.6.29.  Flush posted write in IRQ
handler.

The interrupt line is released by clearing the error status bits
in the MMCHS_STAT register, which must occur before the interrupt
handler returns to avoid unwanted irqs.  Hence the need to flush
the posted write.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NTony Lindgen <tony@atomide.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPierre Ossman <pierre@ossman.eu>

DMA request source (RSSR) needs to be set only once (in probe).
DMA burst length (BLR) need to be set only in set_ios()

This cleans up imxmci_setup_data() and should make it a little
bit faster :)
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Add __init __exit for appropriate probe and remove functions.
Conver to platform_driver_probe()
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This fixes all the checkpatch --file complaints about kernel/ptrace.c
and also removes an unused #include.  I've verified that there are no
changes to the compiled code on x86_64.
Signed-off-by: NRoland McGrath <roland@redhat.com>
[ Removed the parts that just split a line  - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

6260a4b0 ("/proc/pid/maps: don't show
pgoff of pure ANON VMAs" had a typo.

fs/proc/task_nommu.c:138: error: 'struct vm_area_struct' has no member named 'pg_off'
distcc[21484] ERROR: compile fs/proc/task_nommu.c on sprygo/32 failed
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

fs/befs/super.c:85: error: 'PAGE_SIZE' undeclared
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This does the same as commit 9e80d407
(avoid starting a transaction when no block allocation is needed)
but for data=writeback mode of ext3. We also cleanup the data=ordered
case a bit to stick to coding style...
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>