Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 01 9月, 2013 1 次提交
  3. 31 8月, 2013 1 次提交
  5. 30 8月, 2013 1 次提交
  7. 28 8月, 2013 5 次提交
  9. 23 8月, 2013 1 次提交
  11. 21 8月, 2013 7 次提交
  13. 20 8月, 2013 2 次提交
    • H
      ipv6: drop packets with multiple fragmentation headers · f46078cf
      由 Hannes Frederic Sowa 提交于 
      It is not allowed for an ipv6 packet to contain multiple fragmentation
headers. So discard packets which were already reassembled by
fragmentation logic and send back a parameter problem icmp.

The updates for RFC 6980 will come in later, I have to do a bit more
research here.

Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f46078cf
    • H
      ipv6: remove max_addresses check from ipv6_create_tempaddr · 4b08a8f1
      由 Hannes Frederic Sowa 提交于 
      Because of the max_addresses check attackers were able to disable privacy
extensions on an interface by creating enough autoconfigured addresses:

<http://seclists.org/oss-sec/2012/q4/292>

But the check is not actually needed: max_addresses protects the
kernel to install too many ipv6 addresses on an interface and guards
addrconf_prefix_rcv to install further addresses as soon as this limit
is reached. We only generate temporary addresses in direct response of
a new address showing up. As soon as we filled up the maximum number of
addresses of an interface, we stop installing more addresses and thus
also stop generating more temp addresses.

Even if the attacker tries to generate a lot of temporary addresses
by announcing a prefix and removing it again (lifetime == 0) we won't
install more temp addresses, because the temporary addresses do count
to the maximum number of addresses, thus we would stop installing new
autoconfigured addresses when the limit is reached.

This patch fixes CVE-2013-0343 (but other layer-2 attacks are still
possible).

Thanks to Ding Tianhong to bring this topic up again.

Cc: Ding Tianhong <dingtianhong@huawei.com>
Cc: George Kargiotakis <kargig@void.gr>
Cc: P J P <ppandit@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4b08a8f1
  15. 16 8月, 2013 1 次提交
  17. 15 8月, 2013 2 次提交
  19. 14 8月, 2013 1 次提交
    • H
      ipv6: make unsolicited report intervals configurable for mld · fc4eba58
      由 Hannes Frederic Sowa 提交于 
      Commit cab70040 ("net: igmp:
Reduce Unsolicited report interval to 1s when using IGMPv3") and
2690048c ("net: igmp: Allow user-space
configuration of igmp unsolicited report interval") by William Manley made
igmp unsolicited report intervals configurable per interface and corrected
the interval of unsolicited igmpv3 report messages resendings to 1s.

Same needs to be done for IPv6:

MLDv1 (RFC2710 7.10.): 10 seconds
MLDv2 (RFC3810 9.11.): 1 second

Both intervals are configurable via new procfs knobs
mldv1_unsolicited_report_interval and mldv2_unsolicited_report_interval.

(also added .force_mld_version to ipv6_devconf_dflt to bring structs in
line without semantic changes)

v2:
a) Joined documentation update for IPv4 and IPv6 MLD/IGMP
   unsolicited_report_interval procfs knobs.
b) incorporate stylistic feedback from William Manley

v3:
a) add new DEVCONF_* values to the end of the enum (thanks to David
   Miller)

Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: William Manley <william.manley@youview.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fc4eba58
  21. 09 8月, 2013 2 次提交
  23. 08 8月, 2013 1 次提交
  25. 06 8月, 2013 1 次提交
    • D
      net: esp{4,6}: fix potential MTU calculation overflows · 7921895a
      由 Daniel Borkmann 提交于 
      Commit 91657eaf ("xfrm: take net hdr len into account for esp payload
size calculation") introduced a possible interger overflow in
esp{4,6}_get_mtu() handlers in case of x->props.mode equals
XFRM_MODE_TUNNEL. Thus, the following expression will overflow

  unsigned int net_adj;
  ...
  <case ipv{4,6} XFRM_MODE_TUNNEL>
         net_adj = 0;
  ...
  return ((mtu - x->props.header_len - crypto_aead_authsize(esp->aead) -
           net_adj) & ~(align - 1)) + (net_adj - 2);

where (net_adj - 2) would be evaluated as <foo> + (0 - 2) in an unsigned
context. Fix it by simply removing brackets as those operations here
do not need to have special precedence.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Benjamin Poirier <bpoirier@suse.de>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: NBenjamin Poirier <bpoirier@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7921895a
  27. 04 8月, 2013 1 次提交
    • S
      fib_rules: fix suppressor names and default values · 73f5698e
      由 Stefan Tomanek 提交于 
      This change brings the suppressor attribute names into line; it also changes
the data types to provide a more consistent interface.

While -1 indicates that the suppressor is not enabled, values >= 0 for
suppress_prefixlen or suppress_ifgroup  reject routing decisions violating the
constraint.

This changes the previously presented behaviour of suppress_prefixlen, where a
prefix length _less_ than the attribute value was rejected. After this change,
a prefix length less than *or* equal to the value is considered a violation of
the rule constraint.

It also changes the default values for default and newly added rules (disabling
any suppression for those).
Signed-off-by: NStefan Tomanek <stefan.tomanek@wertarbyte.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      73f5698e
  29. 03 8月, 2013 3 次提交
  31. 02 8月, 2013 5 次提交
    • F
      ipv6: bump genid when delete/add address · 439677d7
      由 fan.du 提交于 
      Server           Client
2001:1::803/64  <-> 2001:1::805/64
2001:2::804/64  <-> 2001:2::806/64

Server side fib binary tree looks like this:

                                   (2001:/64)
                                   /
                                  /
                   ffff88002103c380
                 /                 \
     (2)        /                   \
 (2001::803/128)                     ffff880037ac07c0
                                    /               \
                                   /                 \  (3)
                      ffff880037ac0640               (2001::806/128)
                       /             \
             (1)      /               \
        (2001::804/128)               (2001::805/128)

Delete 2001::804/64 won't cause prefix route deleted as well as rt in (3)
destinate to 2001::806 with source address as 2001::804/64. That's because
2001::803/64 is still alive, which make onlink=1 in ipv6_del_addr, this is
where the substantial difference between same prefix configuration and
different prefix configuration :) So packet are still transmitted out to
2001::806 with source address as 2001::804/64.

So bump genid will clear rt in (3), and up layer protocol will eventually
find the right one for themselves.

This problem arised from the discussion in here:
http://marc.info/?l=linux-netdev&m=137404469219410&w=4Signed-off-by: NFan Du <fan.du@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      439677d7
    • J
      ipv6: prevent race between address creation and removal · 8a226b2c
      由 Jiri Benc 提交于 
      There's a race in IPv6 automatic addess assignment. The address is created
with zero lifetime when it's added to various address lists. Before it gets
assigned the correct lifetime, there's a window where a new address may be
configured. This causes the semi-initiated address to be deleted in
addrconf_verify.

This was discovered as a reference leak caused by concurrent run of
__ipv6_ifa_notify for both RTM_NEWADDR and RTM_DELADDR with the same
address.

Fix this by setting the lifetime before the address is added to
inet6_addr_lst.

A few notes:

1. In addrconf_prefix_rcv, by setting update_lft to zero, the
   if (update_lft) { ... } condition is no longer executed for newly
   created addresses. This is okay, as the ifp fields are set in
   ipv6_add_addr now and ipv6_ifa_notify is called (and has been called)
   through addrconf_dad_start.

2. The removal of the whole block under ifp->lock in inet6_addr_add is okay,
   too, as tstamp is initialized to jiffies in ipv6_add_addr.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8a226b2c
    • J
      ipv6: move peer_addr init into ipv6_add_addr() · 3f8f5298
      由 Jiri Pirko 提交于 
      Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3f8f5298
    • M
      ipv6: update ip6_rt_last_gc every time GC is run · 49a18d86
      由 Michal Kubeček 提交于 
      As pointed out by Eric Dumazet, net->ipv6.ip6_rt_last_gc should
hold the last time garbage collector was run so that we should
update it whenever fib6_run_gc() calls fib6_clean_all(), not only
if we got there from ip6_dst_gc().
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      49a18d86
    • M
      ipv6: prevent fib6_run_gc() contention · 2ac3ac8f
      由 Michal Kubeček 提交于 
      On a high-traffic router with many processors and many IPv6 dst
entries, soft lockup in fib6_run_gc() can occur when number of
entries reaches gc_thresh.

This happens because fib6_run_gc() uses fib6_gc_lock to allow
only one thread to run the garbage collector but ip6_dst_gc()
doesn't update net->ipv6.ip6_rt_last_gc until fib6_run_gc()
returns. On a system with many entries, this can take some time
so that in the meantime, other threads pass the tests in
ip6_dst_gc() (ip6_rt_last_gc is still not updated) and wait for
the lock. They then have to run the garbage collector one after
another which blocks them for quite long.

Resolve this by replacing special value ~0UL of expire parameter
to fib6_run_gc() by explicit "force" parameter to choose between
spin_lock_bh() and spin_trylock_bh() and call fib6_run_gc() with
force=false if gc_thresh is reached but not max_size.
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2ac3ac8f
  33. 01 8月, 2013 3 次提交
    • H
      ipv6: fib6_rules should return exact return value · 46b3a421
      由 Hannes Frederic Sowa 提交于 
      With the addition of the suppress operation
(7764a45a ("fib_rules: add .suppress
operation") we rely on accurate error reporting of the fib_rules.actions.

fib6_rule_action always returned -EAGAIN in case we could not find a
matching route and 0 if a rule was matched. This also included a match
for blackhole or prohibited rule actions which could get suppressed by
the new logic.

So adapt fib6_rule_action to always return the correct error code as
its counterpart fib4_rule_action does. This also fixes a possiblity of
nullptr-deref where we don't find a table, thus rt == NULL. Because
the condition rt != ip6_null_entry still holdes it seems we could later
get a nullptr bug on dereference rt->dst.

v2:
a) Fixed a brain fart in the commit msg (the rule => a table, etc). No
   changes to the patch.

Cc: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      46b3a421
    • S
      fib_rules: add .suppress operation · 7764a45a
      由 Stefan Tomanek 提交于 
      This change adds a new operation to the fib_rules_ops struct; it allows the
suppression of routing decisions if certain criteria are not met by its
results.

The first implemented constraint is a minimum prefix length added to the
structures of routing rules. If a rule is added with a minimum prefix length
>0, only routes meeting this threshold will be considered. Any other (more
general) routing table entries will be ignored.

When configuring a system with multiple network uplinks and default routes, it
is often convinient to reference the main routing table multiple times - but
omitting the default route. Using this patch and a modified "ip" utility, this
can be achieved by using the following command sequence:

  $ ip route add table secuplink default via 10.42.23.1

  $ ip rule add pref 100            table main prefixlength 1
  $ ip rule add pref 150 fwmark 0xA table secuplink

With this setup, packets marked 0xA will be processed by the additional routing
table "secuplink", but only if no suitable route in the main routing table can
be found. By using a minimal prefixlength of 1, the default route (/0) of the
table "main" is hidden to packets processed by rule 100; packets traveling to
destinations with more specific routing entries are processed as usual.
Signed-off-by: NStefan Tomanek <stefan.tomanek@wertarbyte.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7764a45a
    • F
      net: split rt_genid for ipv4 and ipv6 · ca4c3fc2
      由 fan.du 提交于 
      Current net name space has only one genid for both IPv4 and IPv6, it has below
drawbacks:

- Add/delete an IPv4 address will invalidate all IPv6 routing table entries.
- Insert/remove XFRM policy will also invalidate both IPv4/IPv6 routing table
  entries even when the policy is only applied for one address family.

Thus, this patch attempt to split one genid for two to cater for IPv4 and IPv6
separately in a fine granularity.
Signed-off-by: NFan Du <fan.du@windriver.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ca4c3fc2
  35. 31 7月, 2013 1 次提交
  37. 29 7月, 2013 1 次提交