It appears that hardened gentoo enables "-fstack-check" by default for
gcc.

That doesn't work _at_all_ for the kernel, because the kernel stack
doesn't act like a user stack at all: it's much smaller, and it doesn't
auto-expand on use.  So the extra "probe one page below the stack" code
generated by -fstack-check just breaks the kernel in horrible ways,
causing infinite double faults etc.

[ I have to say, that the particular code gcc generates looks very
  stupid even for user space where it works, but that's a separate
  issue.  ]
Reported-and-tested-by: NAlexander Tsoy <alexander@tsoy.me>
Reported-and-tested-by: NToralf Förster <toralf.foerster@gmx.de>
Cc: stable@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull x86 page table isolation updates from Thomas Gleixner:
 "This is the final set of enabling page table isolation on x86:

   - Infrastructure patches for handling the extra page tables.

   - Patches which map the various bits and pieces which are required to
     get in and out of user space into the user space visible page
     tables.

   - The required changes to have CR3 switching in the entry/exit code.

   - Optimizations for the CR3 switching along with documentation how
     the ASID/PCID mechanism works.

   - Updates to dump pagetables to cover the user space page tables for
     W+X scans and extra debugfs files to analyze both the kernel and
     the user space visible page tables

  The whole functionality is compile time controlled via a config switch
  and can be turned on/off on the command line as well"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
  x86/ldt: Make the LDT mapping RO
  x86/mm/dump_pagetables: Allow dumping current pagetables
  x86/mm/dump_pagetables: Check user space page table for WX pages
  x86/mm/dump_pagetables: Add page table directory to the debugfs VFS hierarchy
  x86/mm/pti: Add Kconfig
  x86/dumpstack: Indicate in Oops whether PTI is configured and enabled
  x86/mm: Clarify the whole ASID/kernel PCID/user PCID naming
  x86/mm: Use INVPCID for __native_flush_tlb_single()
  x86/mm: Optimize RESTORE_CR3
  x86/mm: Use/Fix PCID to optimize user/kernel switches
  x86/mm: Abstract switching CR3
  x86/mm: Allow flushing for future ASID switches
  x86/pti: Map the vsyscall page if needed
  x86/pti: Put the LDT in its own PGD if PTI is on
  x86/mm/64: Make a full PGD-entry size hole in the memory map
  x86/events/intel/ds: Map debug buffers in cpu_entry_area
  x86/cpu_entry_area: Add debugstore entries to cpu_entry_area
  x86/mm/pti: Map ESPFIX into user space
  x86/mm/pti: Share entry text PMD
  x86/entry: Align entry text section to PMD boundary
  ...

Pull power management fix from Rafael Wysocki:
 "This fixes a schedutil cpufreq governor regression from the 4.14 cycle
  that may cause a CPU idleness check to return incorrect results in
  some cases which leads to suboptimal decisions (Joel Fernandes)"

* tag 'pm-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: schedutil: Use idle_calls counter of the remote CPU

Pull networking fixes from David Miller:

 1) IPv6 gre tunnels end up with different default features enabled
    depending upon whether netlink or ioctls are used to bring them up.
    Fix from Alexey Kodanev.

 2) Fix read past end of user control message in RDS< from Avinash
    Repaka.

 3) Missing RCU barrier in mini qdisc code, from Cong Wang.

 4) Missing policy put when reusing per-cpu route entries, from Florian
    Westphal.

 5) Handle nested PCI errors properly in bnx2x driver, from Guilherme G.
    Piccoli.

 6) Run nested transport mode IPSEC packets via tasklet, from Herbert
    Xu.

 7) Fix handling poll() for stream sockets in tipc, from Parthasarathy
    Bhuvaragan.

 8) Fix two stack-out-of-bounds issues in IPSEC, from Steffen Klassert.

 9) Another zerocopy ubuf handling fix, from Willem de Bruijn.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
  strparser: Call sock_owned_by_user_nocheck
  sock: Add sock_owned_by_user_nocheck
  skbuff: in skb_copy_ubufs unclone before releasing zerocopy
  tipc: fix hanging poll() for stream sockets
  sctp: Replace use of sockets_allocated with specified macro.
  bnx2x: Improve reliability in case of nested PCI errors
  tg3: Enable PHY reset in MTU change path for 5720
  tg3: Add workaround to restrict 5762 MRRS to 2048
  tg3: Update copyright
  net: fec: unmap the xmit buffer that are not transferred by DMA
  tipc: fix tipc_mon_delete() oops in tipc_enable_bearer() error path
  tipc: error path leak fixes in tipc_enable_bearer()
  RDS: Check cmsg_len before dereferencing CMSG_DATA
  tcp: Avoid preprocessor directives in tracepoint macro args
  tipc: fix memory leak of group member when peer node is lost
  net: sched: fix possible null pointer deref in tcf_block_put
  tipc: base group replicast ack counter on number of actual receivers
  net_sched: fix a missing rcu barrier in mini_qdisc_pair_swap()
  net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaround
  ip6_gre: fix device features for ioctl setup
  ...

Pull drm fixes from Dave Airlie:
 "nouveau and i915 regression fixes"

* tag 'drm-fixes-for-v4.15-rc6' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau: fix race when adding delayed work items
  i915: Reject CCS modifiers for pipe C on Geminilake
  drm/i915/gvt: Fix pipe A enable as default for vgpu

Pull clk fix from Stephen Boyd:
 "One more fix for the runtime PM clk patches. We're calling a runtime
  PM API that may schedule from somewhere that we can't do that. We
  change to the async version of pm_runtime_put() to fix it"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: use atomic runtime pm api in clk_core_is_enabled

Merge tag 'led_fixes_for_4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED fix from Jacek Anaszewski:
 "A single LED fix for brightness setting when delay_off is 0"

* tag 'led_fixes_for_4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  led: core: Fix brightness setting when setting delay_off=0

Pull rdma fixes from Jason Gunthorpe:
 "This is the next batch of for-rc patches from RDMA. It includes the
  fix for the ipoib regression I mentioned last time, and the result of
  a fairly major debugging effort to get iser working reliably on cxgb4
  hardware - it turns out the cxgb4 driver was not handling QP error
  flushing properly causing iser to fail.

   - cxgb4 fix for an iser testing failure as debugged by Steve and
     Sagi. The problem was a driver bug in the handling of shutting down
     a QP.

   - Various vmw_pvrdma fixes for bogus WARN_ON, missed resource free on
     error unwind and a use after free bug

   - Improper congestion counter values on mlx5 when link aggregation is
     enabled

   - ipoib lockdep regression introduced in this merge window

   - hfi1 regression supporting the device in a VM introduced in a
     recent patch

   - Typo that breaks future uAPI compatibility in the verbs core

   - More SELinux related oops fixing

   - Fix an oops during error unwind in mlx5"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/mlx5: Fix mlx5_ib_alloc_mr error flow
  IB/core: Verify that QP is security enabled in create and destroy
  IB/uverbs: Fix command checking as part of ib_uverbs_ex_modify_qp()
  IB/mlx5: Serialize access to the VMA list
  IB/hfi: Only read capability registers if the capability exists
  IB/ipoib: Fix lockdep issue found on ipoib_ib_dev_heavy_flush
  IB/mlx5: Fix congestion counters in LAG mode
  RDMA/vmw_pvrdma: Avoid use after free due to QP/CQ/SRQ destroy
  RDMA/vmw_pvrdma: Use refcount_dec_and_test to avoid warning
  RDMA/vmw_pvrdma: Call ib_umem_release on destroy QP path
  iw_cxgb4: when flushing, complete all wrs in a chain
  iw_cxgb4: reflect the original WR opcode in drain cqes
  iw_cxgb4: Only validate the MSN for successful completions

Tom Herbert says:

====================
strparser: Fix lockdep issue

When sock_owned_by_user returns true in strparser. Fix is to add and
call sock_owned_by_user_nocheck since the check for owned by user is
not an error condition in this case.
====================

Fixes: 43a0c675 ("strparser: Stream parser for messages")
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Reported-and-tested-by: <syzbot+c91c53af67f9ebe599a337d2e70950366153b295@syzkaller.appspotmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

strparser wants to check socket ownership without producing any
warnings. As indicated by the comment in the code, it is permissible
for owned_by_user to return true.

Fixes: 43a0c675 ("strparser: Stream parser for messages")
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Reported-and-tested-by: <syzbot+c91c53af67f9ebe599a337d2e70950366153b295@syzkaller.appspotmail.com>
Signed-off-by: NTom Herbert <tom@quantonium.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows checking socket lock ownership with producing lockdep
warnings.
Signed-off-by: NTom Herbert <tom@quantonium.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_copy_ubufs must unclone before it is safe to modify its
skb_shared_info with skb_zcopy_clear.

Commit b90ddd56 ("skbuff: skb_copy_ubufs must release uarg even
without user frags") ensures that all skbs release their zerocopy
state, even those without frags.

But I forgot an edge case where such an skb arrives that is cloned.

The stack does not build such packets. Vhost/tun skbs have their
frags orphaned before cloning. TCP skbs only attach zerocopy state
when a frag is added.

But if TCP packets can be trimmed or linearized, this might occur.
Tracing the code I found no instance so far (e.g., skb_linearize
ends up calling skb_zcopy_clear if !skb->data_len).

Still, it is non-obvious that no path exists. And it is fragile to
rely on this.

Fixes: b90ddd56 ("skbuff: skb_copy_ubufs must release uarg even without user frags")
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 42b531de ("tipc: Fix missing connection request
handling"), we replaced unconditional wakeup() with condtional
wakeup for clients with flags POLLIN | POLLRDNORM | POLLRDBAND.

This breaks the applications which do a connect followed by poll
with POLLOUT flag. These applications are not woken when the
connection is ESTABLISHED and hence sleep forever.

In this commit, we fix it by including the POLLOUT event for
sockets in TIPC_CONNECTING state.

Fixes: 42b531de ("tipc: Fix missing connection request handling")
Acked-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NParthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the recent remote cpufreq callback work, its possible that a cpufreq
update is triggered from a remote CPU. For single policies however, the current
code uses the local CPU when trying to determine if the remote sg_cpu entered
idle or is busy. This is incorrect. To remedy this, compare with the nohz tick
idle_calls counter of the remote CPU.

Fixes: 674e7541 (sched: cpufreq: Allow remote cpufreq callbacks)
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: NJoel Fernandes <joelaf@google.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Daniel Borkmann says:

====================
pull-request: bpf 2017-12-28

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Two small fixes for bpftool. Fix otherwise broken output if any of
   the system calls failed when listing maps in json format and instead
   of bailing out, skip maps or progs that disappeared between fetching
   next id and getting an fd for that id, both from Jakub.

2) Small fix in BPF selftests to respect LLC passed from command line
   when testing for -mcpu=probe presence, from Quentin.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ibmr.device is being set only after ib_alloc_mr() is
(successfully) complete. Therefore, in case mlx5_core_create_mkey()
return with error, the error flow calls mlx5_free_priv_descs()
which uses ibmr.device (which doesn't exist yet), causing
a NULL dereference oops.

To fix this, the IB device should be set in the mr struct earlier
stage (e.g. prior to calling mlx5_core_create_mkey()).

Fixes: 8a187ee5 ("IB/mlx5: Support the new memory registration API")
Signed-off-by: NMax Gurtovoy <maxg@mellanox.com>
Signed-off-by: NNitzan Carmi <nitzanc@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

The XRC target QP create flow sets up qp_sec only if there is an IB link with
LSM security enabled. However, several other related uAPI entry points blindly
follow the qp_sec NULL pointer, resulting in a possible oops.

Check for NULL before using qp_sec.

Cc: <stable@vger.kernel.org> # v4.12
Fixes: d291f1a6 ("IB/core: Enforce PKey security on QPs")
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

If the input command length is larger than the kernel supports an error should
be returned in case the unsupported bytes are not cleared, instead of the
other way aroudn. This matches what all other callers of ib_is_udata_cleared
do and will avoid user ABI problems in the future.

Cc: <stable@vger.kernel.org> # v4.10
Fixes: 189aba99 ("IB/uverbs: Extend modify_qp and support packet pacing")
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

User-space applications can do mmap and munmap directly at
any time.

Since the VMA list is not protected with a mutex, concurrent
accesses to the VMA list from the mmap and munmap can cause
data corruption. Add a mutex around the list.

Cc: <stable@vger.kernel.org> # v4.7
Fixes: 7c2344c3 ("IB/mlx5: Implements disassociate_ucontext API")
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Pull tracing fixes from Steven Rostedt:
 "While doing tests on tracing over the network, I found that the
  packets were getting corrupted.

  In the process I found three bugs.

  One was the culprit, but the other two scared me. After deeper
  investigation, they were not as major as I thought they were, due to a
  signed compared to an unsigned that prevented a negative number from
  doing actual harm.

  The two bigger bugs:

   - Mask the ring buffer data page length. There are data flags at the
     high bits of the length field. These were not cleared via the
     length function, and the length could return a negative number.
     (Although the number returned was unsigned, but was assigned to a
     signed number) Luckily, this value was compared to PAGE_SIZE which
     is unsigned and kept it from entering the path that could have
     caused damage.

   - Check the page usage before reusing the ring buffer reader page.
     TCP increments the page ref when passing the page off to the
     network. The page is passed back to the ring buffer for use on
     free. But the page could still be in use by the TCP stack.

  Minor bugs:

   - Related to the first bug. No need to clear out the unused ring
     buffer data before sending to user space. It is now done by the
     ring buffer code itself.

   - Reset pointers after free on error path. There were some cases in
     the error path that pointers were freed but not set to NULL, and
     could have them freed again, having a pointer freed twice"

* tag 'trace-v4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix possible double free on failure of allocating trace buffer
  tracing: Fix crash when it fails to alloc ring buffer
  ring-buffer: Do no reuse reader page if still in use
  tracing: Remove extra zeroing out of the ring buffer page
  ring-buffer: Mask out the info bits when returning buffer page length

Pull sound fixes from Takashi Iwai:
 "It seems that Santa overslept with a bunch of gifts; the majority of
  changes here are various device-specific ASoC fixes, most notably the
  revert of rcar IOMMU support and fsl_ssi AC97 fixes, but also lots of
  small fixes for codecs. Besides that, the usual HD-audio quirks and
  fixes are included, too"

* tag 'sound-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (31 commits)
  ALSA: hda - Fix missing COEF init for ALC225/295/299
  ALSA: hda: Drop useless WARN_ON()
  ALSA: hda - change the location for one mic on a Lenovo machine
  ALSA: hda - fix headset mic detection issue on a Dell machine
  ALSA: hda - Add MIC_NO_PRESENCE fixup for 2 HP machines
  ASoC: rsnd: fixup ADG register mask
  ASoC: rt5514-spi: only enable wakeup when fully initialized
  ASoC: nau8825: fix issue that pop noise when start capture
  ASoC: rt5663: Fix the wrong result of the first jack detection
  ASoC: rsnd: ssi: fix race condition in rsnd_ssi_pointer_update
  ASoC: Intel: Change kern log level to avoid unwanted messages
  ASoC: atmel-classd: select correct Kconfig symbol
  ASoC: wm_adsp: Fix validation of firmware and coeff lengths
  ASoC: Intel: Skylake: Do not check dev_type for dmic link type
  ASoC: rockchip: disable clock on error
  ASoC: tlv320aic31xx: Fix GPIO1 register definition
  ASoC: codecs: msm8916-wcd: Fix supported formats
  ASoC: fsl_asrc: Fix typo in a field define
  ASoC: rsnd: ssiu: clear SSI_MODE for non TDM Extended modes
  ASoC: da7218: Correct IRQ level in DT binding example
  ...

With the current code, the following sequence won't work :
echo timer > trigger

echo 0 >  delay_off
* at this point we call
** led_delay_off_store
** led_blink_set
*** stop timer
** led_blink_setup
** led_set_software_blink
*** if !delay_on, led off
*** if !delay_off, set led_set_brightness_nosleep <--- LED_BLINK_SW is set but timer is stop
*** otherwise start timer/set LED_BLINK_SW flag

echo xxx > brightness
* led_set_brightness
** if LED_BLINK_SW
*** if brightness=0, led off
*** else apply brightness if next timer <--- timer is stop, and will never apply new setting
** otherwise set led_set_brightness_nosleep

To fix that, when we delete the timer, we should clear LED_BLINK_SW.

Cc: linux-leds@vger.kernel.org
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: NJacek Anaszewski <jacek.anaszewski@gmail.com>

Jing Xia and Chunyan Zhang reported that on failing to allocate part of the
tracing buffer, memory is freed, but the pointers that point to them are not
initialized back to NULL, and later paths may try to free the freed memory
again. Jing and Chunyan fixed one of the locations that does this, but
missed a spot.

Link: http://lkml.kernel.org/r/20171226071253.8968-1-chunyan.zhang@spreadtrum.com

Cc: stable@vger.kernel.org
Fixes: 737223fb ("tracing: Consolidate buffer allocation code")
Reported-by: NJing Xia <jing.xia@spreadtrum.com>
Reported-by: NChunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>

Double free of the ring buffer happens when it fails to alloc new
ring buffer instance for max_buffer if TRACER_MAX_TRACE is configured.
The root cause is that the pointer is not set to NULL after the buffer
is freed in allocate_trace_buffers(), and the freeing of the ring
buffer is invoked again later if the pointer is not equal to Null,
as:

instance_mkdir()
    |-allocate_trace_buffers()
        |-allocate_trace_buffer(tr, &tr->trace_buffer...)
	|-allocate_trace_buffer(tr, &tr->max_buffer...)

          // allocate fail(-ENOMEM),first free
          // and the buffer pointer is not set to null
        |-ring_buffer_free(tr->trace_buffer.buffer)

       // out_free_tr
    |-free_trace_buffers()
        |-free_trace_buffer(&tr->trace_buffer);

	      //if trace_buffer is not null, free again
	    |-ring_buffer_free(buf->buffer)
                |-rb_free_cpu_buffer(buffer->buffers[cpu])
                    // ring_buffer_per_cpu is null, and
                    // crash in ring_buffer_per_cpu->pages

Link: http://lkml.kernel.org/r/20171226071253.8968-1-chunyan.zhang@spreadtrum.com

Cc: stable@vger.kernel.org
Fixes: 737223fb ("tracing: Consolidate buffer allocation code")
Signed-off-by: NJing Xia <jing.xia@spreadtrum.com>
Signed-off-by: NChunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>

To free the reader page that is allocated with ring_buffer_alloc_read_page(),
ring_buffer_free_read_page() must be called. For faster performance, this
page can be reused by the ring buffer to avoid having to free and allocate
new pages.

The issue arises when the page is used with a splice pipe into the
networking code. The networking code may up the page counter for the page,
and keep it active while sending it is queued to go to the network. The
incrementing of the page ref does not prevent it from being reused in the
ring buffer, and this can cause the page that is being sent out to the
network to be modified before it is sent by reading new data.

Add a check to the page ref counter, and only reuse the page if it is not
being used anywhere else.

Cc: stable@vger.kernel.org
Fixes: 73a757e6 ("ring-buffer: Return reader page back into existing ring buffer")
Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>

The ring_buffer_read_page() takes care of zeroing out any extra data in the
page that it returns. There's no need to zero it out again from the
consumer. It was removed from one consumer of this function, but
read_buffers_splice_read() did not remove it, and worse, it contained a
nasty bug because of it.

Cc: stable@vger.kernel.org
Fixes: 2711ca23 ("ring-buffer: Move zeroing out excess in page to ring buffer code")
Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>

Merge tag 'drm-intel-fixes-2017-12-22-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

GLK pipe C related fix, and a gvt fix.

* tag 'drm-intel-fixes-2017-12-22-1' of git://anongit.freedesktop.org/drm/drm-intel:
  i915: Reject CCS modifiers for pipe C on Geminilake
  drm/i915/gvt: Fix pipe A enable as default for vgpu

Two info bits were added to the "commit" part of the ring buffer data page
when returned to be consumed. This was to inform the user space readers that
events have been missed, and that the count may be stored at the end of the
page.

What wasn't handled, was the splice code that actually called a function to
return the length of the data in order to zero out the rest of the page
before sending it up to user space. These data bits were returned with the
length making the value negative, and that negative value was not checked.
It was compared to PAGE_SIZE, and only used if the size was less than
PAGE_SIZE. Luckily PAGE_SIZE is unsigned long which made the compare an
unsigned compare, meaning the negative size value did not end up causing a
large portion of memory to be randomly zeroed out.

Cc: stable@vger.kernel.org
Fixes: 66a8cb95 ("ring-buffer: Add place holder recording of dropped events")
Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>

The patch(180d8cd9) replaces all uses of struct sock fields'
memory_pressure, memory_allocated, sockets_allocated, and sysctl_mem
to accessor macros. But the sockets_allocated field of sctp sock is
not replaced at all. Then replace it now for unifying the code.

Fixes: 180d8cd9 ("foundations of per-cgroup memory pressure controlling.")
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: NTonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While in recovery process of PCI error (called EEH on PowerPC arch),
another PCI transaction could be corrupted causing a situation of
nested PCI errors. Also, this scenario could be reproduced with
error injection mechanisms (for debug purposes).

We observe that in case of nested PCI errors, bnx2x might attempt to
initialize its shmem and cause a kernel crash due to bad addresses
read from MCP. Multiple different stack traces were observed depending
on the point the second PCI error happens.

This patch avoids the crashes by:

 * failing PCI recovery in case of nested errors (since multiple
 PCI errors in a row are not expected to lead to a functional
 adapter anyway), and by,

 * preventing access to adapter FW when MCP is failed (we mark it as
 failed when shmem cannot get initialized properly).
Reported-by: NAbdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: NGuilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: NShahed Shaikh <Shahed.Shaikh@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Siva Reddy Kallam says:

====================
tg3: update on copyright and couple of fixes

First patch:
	Update copyright

Second patch:
	Add workaround to restrict 5762 MRRS

Third patch:
	Add PHY reset in change MTU path for 5720
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A customer noticed RX path hang when MTU is changed on the fly while
running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720
belongs to same ASIC family, we observed same issue and same fix
could solve this problem for 5720.
Signed-off-by: NSiva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of AMD based server with 5762 hangs with jumbo frame traffic.
This AMD platform has southbridge limitation which is restricting MRRS
to 4000. As a work around, driver to restricts the MRRS to 2048 for
this particular 5762 NX1 card.
Signed-off-by: NSiva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSiva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2017-12-22

1) Check for valid id proto in validate_tmpl(), otherwise
   we may trigger a warning in xfrm_state_fini().
   From Cong Wang.

2) Fix a typo on XFRMA_OUTPUT_MARK policy attribute.
   From Michal Kubecek.

3) Verify the state is valid when encap_type < 0,
   otherwise we may crash on IPsec GRO .
   From Aviv Heller.

4) Fix stack-out-of-bounds read on socket policy lookup.
   We access the flowi of the wrong address family in the
   IPv4 mapped IPv6 case, fix this by catching address
   family missmatches before we do the lookup.

5) fix xfrm_do_migrate() with AEAD to copy the geniv
   field too. Otherwise the state is not fully initialized
   and migration fails. From Antony Antony.

6) Fix stack-out-of-bounds with misconfigured transport
   mode policies. Our policy template validation is not
   strict enough. It is possible to configure policies
   with transport mode template where the address family
   of the template does not match the selectors address
   family. Fix this by refusing such a configuration,
   address family can not change on transport mode.

7) Fix a policy reference leak when reusing pcpu xdst
   entry. From Florian Westphal.

8) Reinject transport-mode packets through tasklet,
   otherwise it is possible to reate a recursion
   loop. From Herbert Xu.

Please pull or let me know if there are problems.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The enet IP only support 32 bit, it will use swiotlb buffer to do dma
mapping when xmit buffer DMA memory address is bigger than 4G in i.MX
platform. After stress suspend/resume test, it will print out:

log:
[12826.352864] fec 5b040000.ethernet: swiotlb buffer is full (sz: 191 bytes)
[12826.359676] DMA: Out of SW-IOMMU space for 191 bytes at device 5b040000.ethernet
[12826.367110] fec 5b040000.ethernet eth0: Tx DMA memory map failed

The issue is that the ready xmit buffers that are dma mapped but DMA still
don't copy them into fifo, once MAC restart, these DMA buffers are not unmapped.
So it should check the dma mapping buffer and unmap them.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling tipc_mon_delete() before the monitor has been created will oops.
This can happen in tipc_enable_bearer() error path if tipc_disc_create()
fails.

[   48.589074] BUG: unable to handle kernel paging request at 0000000000001008
[   48.590266] IP: tipc_mon_delete+0xea/0x270 [tipc]
[   48.591223] PGD 1e60c5067 P4D 1e60c5067 PUD 1eb0cf067 PMD 0
[   48.592230] Oops: 0000 [#1] SMP KASAN
[   48.595610] CPU: 5 PID: 1199 Comm: tipc Tainted: G    B            4.15.0-rc4-pc64-dirty #5
[   48.597176] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
[   48.598489] RIP: 0010:tipc_mon_delete+0xea/0x270 [tipc]
[   48.599347] RSP: 0018:ffff8801d827f668 EFLAGS: 00010282
[   48.600705] RAX: ffff8801ee813f00 RBX: 0000000000000204 RCX: 0000000000000000
[   48.602183] RDX: 1ffffffff1de6a75 RSI: 0000000000000297 RDI: 0000000000000297
[   48.604373] RBP: 0000000000000000 R08: 0000000000000000 R09: fffffbfff1dd1533
[   48.605607] R10: ffffffff8eafbb05 R11: fffffbfff1dd1534 R12: 0000000000000050
[   48.607082] R13: dead000000000200 R14: ffffffff8e73f310 R15: 0000000000001020
[   48.608228] FS:  00007fc686484800(0000) GS:ffff8801f5540000(0000) knlGS:0000000000000000
[   48.610189] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   48.611459] CR2: 0000000000001008 CR3: 00000001dda70002 CR4: 00000000003606e0
[   48.612759] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   48.613831] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   48.615038] Call Trace:
[   48.615635]  tipc_enable_bearer+0x415/0x5e0 [tipc]
[   48.620623]  tipc_nl_bearer_enable+0x1ab/0x200 [tipc]
[   48.625118]  genl_family_rcv_msg+0x36b/0x570
[   48.631233]  genl_rcv_msg+0x5a/0xa0
[   48.631867]  netlink_rcv_skb+0x1cc/0x220
[   48.636373]  genl_rcv+0x24/0x40
[   48.637306]  netlink_unicast+0x29c/0x350
[   48.639664]  netlink_sendmsg+0x439/0x590
[   48.642014]  SYSC_sendto+0x199/0x250
[   48.649912]  do_syscall_64+0xfd/0x2c0
[   48.650651]  entry_SYSCALL64_slow_path+0x25/0x25
[   48.651843] RIP: 0033:0x7fc6859848e3
[   48.652539] RSP: 002b:00007ffd25dff938 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[   48.654003] RAX: ffffffffffffffda RBX: 00007ffd25dff990 RCX: 00007fc6859848e3
[   48.655303] RDX: 0000000000000054 RSI: 00007ffd25dff990 RDI: 0000000000000003
[   48.656512] RBP: 00007ffd25dff980 R08: 00007fc685c35fc0 R09: 000000000000000c
[   48.657697] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000d13010
[   48.658840] R13: 00007ffd25e009c0 R14: 0000000000000000 R15: 0000000000000000
[   48.662972] RIP: tipc_mon_delete+0xea/0x270 [tipc] RSP: ffff8801d827f668
[   48.664073] CR2: 0000000000001008
[   48.664576] ---[ end trace e811818d54d5ce88 ]---
Acked-by: NYing Xue <ying.xue@windriver.com>
Acked-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NTommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix memory leak in tipc_enable_bearer() if enable_media() fails, and
cleanup with bearer_disable() if tipc_mon_create() fails.
Acked-by: NYing Xue <ying.xue@windriver.com>
Acked-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NTommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RDS currently doesn't check if the length of the control message is
large enough to hold the required data, before dereferencing the control
message data. This results in following crash:

BUG: KASAN: stack-out-of-bounds in rds_rdma_bytes net/rds/send.c:1013
[inline]
BUG: KASAN: stack-out-of-bounds in rds_sendmsg+0x1f02/0x1f90
net/rds/send.c:1066
Read of size 8 at addr ffff8801c928fb70 by task syzkaller455006/3157

CPU: 0 PID: 3157 Comm: syzkaller455006 Not tainted 4.15.0-rc3+ #161
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x194/0x257 lib/dump_stack.c:53
 print_address_description+0x73/0x250 mm/kasan/report.c:252
 kasan_report_error mm/kasan/report.c:351 [inline]
 kasan_report+0x25b/0x340 mm/kasan/report.c:409
 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:430
 rds_rdma_bytes net/rds/send.c:1013 [inline]
 rds_sendmsg+0x1f02/0x1f90 net/rds/send.c:1066
 sock_sendmsg_nosec net/socket.c:628 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:638
 ___sys_sendmsg+0x320/0x8b0 net/socket.c:2018
 __sys_sendmmsg+0x1ee/0x620 net/socket.c:2108
 SYSC_sendmmsg net/socket.c:2139 [inline]
 SyS_sendmmsg+0x35/0x60 net/socket.c:2134
 entry_SYSCALL_64_fastpath+0x1f/0x96
RIP: 0033:0x43fe49
RSP: 002b:00007fffbe244ad8 EFLAGS: 00000217 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fe49
RDX: 0000000000000001 RSI: 000000002020c000 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000217 R12: 00000000004017b0
R13: 0000000000401840 R14: 0000000000000000 R15: 0000000000000000

To fix this, we verify that the cmsg_len is large enough to hold the
data to be read, before proceeding further.
Reported-by: Nsyzbot <syzkaller-bugs@googlegroups.com>
Signed-off-by: NAvinash Repaka <avinash.repaka@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Reviewed-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was a long-standing problem on HP Spectre X360 with Kabylake
where it lacks of the front speaker output in some situations.  Also
there are other products showing the similar behavior.  The culprit
seems to be the missing COEF setup on ALC codecs, ALC225/295/299,
which are all compatible.

This patch adds the proper COEF setup (to initialize idx 0x67 / bits
0x3000) for addressing the issue.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195457
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>