On enslave failure primary_slave can point to new_slave which is to be
freed, and the same applies to curr_active_slave. So check if this is
the case and clean up properly after err_detach because that's the first
error code path after they're set.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The main problem is with vid refcount which only gets bumped up.
Delete the vlans after err_detach as that's the first error path
after the vlans are added.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add bond_mc_list_flush() after err_detach as that's the first error path
after the addresses are added. The main issue is the mc addresses' refcount
which only gets bumped up.

v2: update log message and don't move code unnecessarily
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 6b923cb7 (bonding: support for IPv6 transmit hashing)
bonding doesn't properly hash traffic in forwarding setups.

Vitaly V. Bursov diagnosed that skb_network_header_len() returned 0 in
this case.

More generally, the transport header might not be in the skb head.

Use pskb_may_pull() & skb_header_pointer() to get it right, and use
proto_ports_offset() in bond_xmit_hash_policy_l34() to get support for
more protocols than TCP and UDP.
Reported-by: NVitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: John Eaglesham <linux@8192.net>
Tested-by: NVitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes 2 issues regarding bnx2x's status blocks:

   1. ethtool -c caused corruption of status blocks in FW RAM.

   2. when using multi-CoS, the configuration of the timeout values of
      status blocks is incorrect, harming the coalescing of interrupts
      for such CoSs.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When loading after UNDI (e.g., Boot from SAN) the UNDI does not
gracefully yield its resources; The bnx2x driver handles that release
itself.

During the manipulation required to release those resources, it's possible
for the UNDI to try and write to memory regions which are no longer accessible,
causing the PCI bus to prevent further writes from the chip.

This would in turn cause DMAE timeouts later on in the driver, as the driver
will be unable to use the chip's DMA engines.

This patch prevents the chip from actually writing through the PCI bus
in said scenario, thus allowing the release without the unfortunate by-product.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Debug logs were not matching with code functionality.
o Changed dev_info to netdev_err
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When driver receives a packet with gso size > 0 and when TSO is disabled,
it should be transmitted as a TSO packet to prevent Tx timeout and subsequent
firmware reset.
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before conducting loopback test by sending packets, driver should stop transmit
queue and turn off carrier.
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PF driver does not check if the administrator has already set a VF
VLAN via the PF driver before setting the new VLAN.  This results in
the following scenario:

A) Administrator sets VF <n> to VLAN 100
B) Administrator sets VF <x> to VLAN 100
C) Administrator sets VF <n> to VLAN 200
D) The VF <n> driver continues to be able to receive traffic on VLAN
   100 because the VLVFB pool enable bit for that VF was left set
   instead of being cleared as it should be.

This fix ensures that the old VLAN filter for VF <n> is first removed
and the pool bit enable for VF <n> is cleared so that it no longer
receives traffic on VLAN 100.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch actually reverts:
igb: Support using build_skb in the case that jumbo frames are disabled

The reason for reverting this patch is that it can lead to data corruption.
The following flow was pointed out by Ben Hutchings:

1. skb is forwarded to another device
2. Packet headers are modified and it's put into a queue
3. Second packet is received into the other half of this page
4. Page cannot be reused, so is DMA-unmapped
5. The DMA mapping was non-coherent, so unmap copies or invalidates
cache

The headers added in step 2 get trashed in step 5.
Reported-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's possible that the reference to the object request dropped
inside the loop in rbd_img_request_submit() will be the last
one, in which case the content of the object pointer can't be
trusted.

Use a safe form of the object request list traversal to avoid
problems.

This resolves:
    http://tracker.ceph.com/issues/4705Signed-off-by: NAlex Elder <elder@inktank.com>
Reviewed-by: NJosh Durgin <josh.durgin@inktank.com>

o Commit 319ecf12
  ("qlcnic: 83xx sysfs routines") introduced regression
  for beaconing test while refactoring 82xx code. This patch is to
  revert code to fix beaconing test for 82xx adapter.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A link-down isn't properly saved in the FEC state, so we wouldn't restart the
FEC after a repeated link-up.

Regression was introduced with commit
d97e7497 "net: fec: restart the FEC when PHY speed changes"
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The intention was to test against the constant, not the size of
the constant.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dual EMAC slave VLAN id must be got from slave node instead of cpsw node as
VLAN id for each slave will be different.
Reported-by: NMark Jackson <mpfj-list@mimc.co.uk>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mvneta_tx() was using a static tx queue number causing crashes as
soon as a little bit of traffic was sent via the interface, because
it is normally expected that the same queue should be used as in
dev_queue_xmit().

As suggested by Ben Hutchings, let's use skb_get_queue_mapping() to
get the proper Tx queue number, and use alloc_etherdev_mqs() instead
of alloc_etherdev_mq() to create the queues.

Both my Mirabox and my OpenBlocks AX3 used to crash without this patch
and don't anymore with it. The issue appeared in 3.8 but became more
visible after the fix allowing GSO to be enabled.

Original work was done by Dmitri Epshtein and Thomas Petazzoni. I
just adapted it to take care of Ben's comments.
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Cc: Dmitri Epshtein <dima@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NPrzemo Firszt <przemo@firszt.eu>
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Tested-by: NPrzemo Firszt <przemo@firszt.eu>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Compiling the at91rm9200_wdt.c driver without at91rm9200
support was leading to several errors:

drivers/built-in.o: In function `at91_wdt_close':
at91_adc.c:(.text+0xc9fe4): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91_wdt_write':
at91_adc.c:(.text+0xca004): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91wdt_shutdown':
at91_adc.c:(.text+0xca01c): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91wdt_suspend':
at91_adc.c:(.text+0xca038): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91_wdt_open':
at91_adc.c:(.text+0xca0cc): undefined reference to `at91_st_base'
drivers/built-in.o:at91_adc.c:(.text+0xca2c8): more undefined references to
`at91_st_base' follow

So, reverting the modification of the "depends" Kconfig line
introduced by patch a6a1bcd3 (watchdog: at91rm9200: add DT support)
seems to be the good solution.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The mvmdio driver uses the phylib API, so it should select the PHYLIB
symbol, otherwise, a build with mvmdio (but without mvneta) fails to
build with undefined symbols such as mdiobus_unregister, mdiobus_free,
etc.

The mvneta driver does not use the phylib API directly, so it does not
need to select PHYLIB. It already selects the mvmdio driver anyway.

Historically, this problem is due to the fact that the PHY handling
was originally part of mvneta, and was later moved to a separate
driver, without updating the Kconfig select statements
accordingly. And since there was no functional reason to use mvmdio
without mvneta, this case was not tested.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.

[ Bug added in linux-3.8 , commit 4008e97f
  ("tuntap: fix ambigious multiqueue API") ]
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver should use return value of __vlan_put_tag with appropriate
NULL-check instead of old skb pointer.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware parsing of Control Wrapper Frames needs to be disabled, as
it has been causing spurious decryption error reports. The initvals for
other chips have been updated to disable it, but AR9580 was left out for
some reason.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To get correct endianes on little endian cpus (like arm) while reading device
tree properties, this patch replaces of_get_property() with
of_property_read_u32(). While there use of_property_read_bool() for the
handling of the boolean "nxp,no-comparator-bypass" property.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Since commit:

    1c6c6952 genirq: Reject bogus threaded irq requests

threaded irqs must provide a primary handler or set the IRQF_ONESHOT flag.
Since the mcp251x driver doesn't make use of a primary handler set the
IRQF_ONESHOT flag.

Cc: linux-stable <stable@vger.kernel.org> # >= v3.5
Reported-by: NMylene Josserand <Mylene.Josserand@navocap.com>
Tested-by: NMylene Josserand <Mylene.Josserand@navocap.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Driver's and ->fill_modes functions are allowed to grab crtc mutexes
(for e.g. load detect). Hence we need to first only grab the general
kms mutex, and only in a second step grab all locks to do the
modesets.

This prevents a deadlock on my gm45 in the tv load detect code called
by drm_helper_probe_single_connector_modes.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Don't oops seems proper.

Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

The dereference to 'put_index' should be moved below the NULL test.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If the DesignWare MAC is synthesised with MMC RX IPC Counter, an unmanaged
and unacknowledged interrupt is generated after some time of operation.

This patch masks the undesired interrupts.
Signed-off-by: NChristian Ruppert <christian.ruppert@abilis.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While enslaving a new device and after IFF_BONDING flag is set, in case
of failure it is not stripped from the device's priv_flags while
cleaning up, which could lead to other problems.
Cleaning at err_close because the flag is set after dev_open().

v2: no change
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 471cb5a3 ("bonding: remove
usage of dev->master") a bug was introduced which causes a NULL pointer
dereference. If a bond device is in mode 6 (ALB) and a slave is added
it will dereference a NULL pointer in bond_slave_netdev_event().
This is because in bond_enslave we have bond_alb_init_slave() which
changes the MAC address of the slave and causes a NETDEV_CHANGEADDR.
Then we have in bond_slave_netdev_event():
        struct slave *slave = bond_slave_get_rtnl(slave_dev);
        struct bonding *bond = slave->bond;
bond_slave_get_rtnl() dereferences slave_dev->rx_handler_data which at
that time is NULL since netdev_rx_handler_register() is called later.

This is fixed by checking if slave is NULL before dereferencing it.

v2: Comment style changed.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We actually have to pass chip as the host_data parameter of
irq_domain_add_simple() as later on, it is used to initialize chip_data
in pca953x_gpio_irq_map(). Failing to do so is leading to a NULL pointer
dereference after calling irq_data_get_irq_chip_data() in
pca953x_irq_mask(), pca953x_irq_unmask(), pca953x_irq_bus_lock(),
pca953x_irq_bus_sync_unlock() and pca953x_irq_set_type().

Fixes regression introduced by commit
0e8f2fda (gpio: pca953x: use simple
irqdomain)
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch fixes a bug where a handful of informational / control CDBs
that should be allowed during ALUA access state Standby/Offline/Transition
where incorrectly returning CHECK_CONDITION + ASCQ_04H_ALUA_TG_PT_*.

This includes INQUIRY + REPORT_LUNS, which would end up preventing LUN
registration when LUN scanning occured during these ALUA access states.

Cc: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Send bad target to guest in case:
1) we can not allocate the cmd
2) fail to submit the cmd
Signed-off-by: NAsias He <asias@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Share the send bad target code with other use cases.
Signed-off-by: NAsias He <asias@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

If we fail to submit the allocated tv_vmd to tcm_vhost_submission_work,
we will leak the tv_vmd. Free tv_vmd on fail path.
Signed-off-by: NAsias He <asias@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

We did the length of response check twice.
Signed-off-by: NAsias He <asias@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The cnic module is responsible for initializing various bnx2x structs
via callbacks provided by the bnx2x module.
One such struct is the queue object for the FCoE queue.

If a device is working in AFEX mode and its configuration allows FCoE yet
the cnic module is not loaded, it's very likely a null pointer dereference
will occur, as the bnx2x will erroneously access the FCoE's queue object.

Prevent said access until cnic properly registers itself.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

e100 uses pci_map_single, but fails to check for a dma mapping error after its
use, resulting in a stack trace:

[   46.656594] ------------[ cut here ]------------
[   46.657004] WARNING: at lib/dma-debug.c:933 check_unmap+0x47b/0x950()
[   46.657004] Hardware name: To Be Filled By O.E.M.
[   46.657004] e100 0000:00:0e.0: DMA-API: device driver failed to check map
error[device address=0x000000007a4540fa] [size=90 bytes] [mapped as single]
[   46.657004] Modules linked in:
[   46.657004]  w83627hf hwmon_vid snd_via82xx ppdev snd_ac97_codec ac97_bus
snd_seq snd_pcm snd_mpu401 snd_mpu401_uart ns558 snd_rawmidi gameport parport_pc
e100 snd_seq_device parport snd_page_alloc snd_timer snd soundcore skge shpchp
k8temp mii edac_core i2c_viapro edac_mce_amd nfsd auth_rpcgss nfs_acl lockd
sunrpc binfmt_misc uinput ata_generic pata_acpi radeon i2c_algo_bit
drm_kms_helper ttm firewire_ohci drm firewire_core pata_via sata_via i2c_core
sata_promise crc_itu_t
[   46.657004] Pid: 792, comm: ip Not tainted 3.8.0-0.rc6.git0.1.fc19.x86_64 #1
[   46.657004] Call Trace:
[   46.657004]  <IRQ>  [<ffffffff81065ed0>] warn_slowpath_common+0x70/0xa0
[   46.657004]  [<ffffffff81065f4c>] warn_slowpath_fmt+0x4c/0x50
[   46.657004]  [<ffffffff81364cfb>] check_unmap+0x47b/0x950
[   46.657004]  [<ffffffff8136522f>] debug_dma_unmap_page+0x5f/0x70
[   46.657004]  [<ffffffffa030f0f0>] ? e100_tx_clean+0x30/0x210 [e100]
[   46.657004]  [<ffffffffa030f1a8>] e100_tx_clean+0xe8/0x210 [e100]
[   46.657004]  [<ffffffffa030fc6f>] e100_poll+0x56f/0x6c0 [e100]
[   46.657004]  [<ffffffff8159dce1>] ? net_rx_action+0xa1/0x370
[   46.657004]  [<ffffffff8159ddb2>] net_rx_action+0x172/0x370
[   46.657004]  [<ffffffff810703bf>] __do_softirq+0xef/0x3d0
[   46.657004]  [<ffffffff816e4ebc>] call_softirq+0x1c/0x30
[   46.657004]  [<ffffffff8101c485>] do_softirq+0x85/0xc0
[   46.657004]  [<ffffffff81070885>] irq_exit+0xd5/0xe0
[   46.657004]  [<ffffffff816e5756>] do_IRQ+0x56/0xc0
[   46.657004]  [<ffffffff816dacb2>] common_interrupt+0x72/0x72
[   46.657004]  <EOI>  [<ffffffff816da1eb>] ?
_raw_spin_unlock_irqrestore+0x3b/0x70
[   46.657004]  [<ffffffff816d124d>] __slab_free+0x58/0x38b
[   46.657004]  [<ffffffff81214424>] ? fsnotify_clear_marks_by_inode+0x34/0x120
[   46.657004]  [<ffffffff811b0417>] ? kmem_cache_free+0x97/0x320
[   46.657004]  [<ffffffff8157fc14>] ? sock_destroy_inode+0x34/0x40
[   46.657004]  [<ffffffff8157fc14>] ? sock_destroy_inode+0x34/0x40
[   46.657004]  [<ffffffff811b0692>] kmem_cache_free+0x312/0x320
[   46.657004]  [<ffffffff8157fc14>] sock_destroy_inode+0x34/0x40
[   46.657004]  [<ffffffff811e8c28>] destroy_inode+0x38/0x60
[   46.657004]  [<ffffffff811e8d5e>] evict+0x10e/0x1a0
[   46.657004]  [<ffffffff811e9605>] iput+0xf5/0x180
[   46.657004]  [<ffffffff811e4338>] dput+0x248/0x310
[   46.657004]  [<ffffffff811ce0e1>] __fput+0x171/0x240
[   46.657004]  [<ffffffff811ce26e>] ____fput+0xe/0x10
[   46.657004]  [<ffffffff8108d54c>] task_work_run+0xac/0xe0
[   46.657004]  [<ffffffff8106c6ed>] do_exit+0x26d/0xc30
[   46.657004]  [<ffffffff8109eccc>] ? finish_task_switch+0x7c/0x120
[   46.657004]  [<ffffffff816dad58>] ? retint_swapgs+0x13/0x1b
[   46.657004]  [<ffffffff8106d139>] do_group_exit+0x49/0xc0
[   46.657004]  [<ffffffff8106d1c4>] sys_exit_group+0x14/0x20
[   46.657004]  [<ffffffff816e3b19>] system_call_fastpath+0x16/0x1b
[   46.657004] ---[ end trace 4468c44e2156e7d1 ]---
[   46.657004] Mapped at:
[   46.657004]  [<ffffffff813663d1>] debug_dma_map_page+0x91/0x140
[   46.657004]  [<ffffffffa030e8eb>] e100_xmit_prepare+0x12b/0x1c0 [e100]
[   46.657004]  [<ffffffffa030c924>] e100_exec_cb+0x84/0x140 [e100]
[   46.657004]  [<ffffffffa030e56a>] e100_xmit_frame+0x3a/0x190 [e100]
[   46.657004]  [<ffffffff8159ee89>] dev_hard_start_xmit+0x259/0x6c0

Easy fix, modify the cb paramter to e100_exec_cb to return an error, and do the
dma_mapping_error check in the obvious place

This was reported previously here:
http://article.gmane.org/gmane.linux.network/257893

But nobody stepped up and fixed it.

CC: Josh Boyer <jwboyer@redhat.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Reported-by: NMichal Jaegermann <michal@harddata.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And make use of it in b43. This fixes a regression introduced with
49d55cef
b43: N-PHY: implement spurious tone avoidance
This commit made BCM4322 use only MCS 0 on channel 13, which of course
resulted in performance drop (down to 0.7Mb/s).
Reported-by: NStefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>