Add names for our lockdep classes, so instead of having to decipher
lockdep output with mysterious names:

    Chain exists of:
      key#14 --> key#11 --> key#13

lockdep will give us something nicer:

    Chain exists of:
      SRQ-uobj --> PD-uobj --> CQ-uobj
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.

After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.

ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot)  If these resources are all ON,
then the state is D3hot.  If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.

This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: NAaron Lu <aaron.lu@amd.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

So that the power button still wakes up the platform.
Signed-off-by: NPierre Tardy <pierre.tardy@intel.com>
Link: http://lkml.kernel.org/r/20120504210244.F2EA5A018B@akpm.mtv.corp.google.comTested-by: NKangkai Yin <kangkai.yin@intel.com>
Tested-by: NYong Wang <yong.y.wang@intel.com>
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Use family rather than DCE check for clarity, also always use
wb on APUs, there will never be AGP variants.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

commit 61a0d80c "md/bitmap: discard CHUNK_BLOCK_SHIFT macro"
replaced CHUNK_BLOCK_RATIO() by the same text that was
replacing CHUNK_BLOCK_SHIFT() - which is clearly wrong.

The result is that 'chunks' is often too small by 1,
which can sometimes result in a crash (not sure how).

So use the correct replacement, and get rid of CHUNK_BLOCK_RATIO
which is no longe used.
Reported-by: NKarl Newman <siliconfiend@gmail.com>
Tested-by: NKarl Newman <siliconfiend@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Ben Hutchings pointed out that the validation in efivars was inadequate -
most obviously, an entry with size 0 would server as a DoS against the
kernel. Improve this based on his suggestions.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SPEAr13xx series of SoCs contain Synopsys AHCI SATA Controller which shares
ahci_platform driver with other controller versions.

This patch updates DT compatible list for ahci_platform. It also updates and
renames binding documentation to more generic name.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

#ifdef, #endif is not required in definition/usage of arasan_cf_pm_ops. So, move
this definition and its usage outside of them.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When comparing the dmesg between 3.4-rc3 and 3.4-rc4 I found the
following differences:

 -ata1: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
 -ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
 -ata3: DUMMY
 +ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
 +ata3: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
  ata4: DUMMY
  ata5: DUMMY
 -ata6: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
 +ata6: DUMMY
 +ata7: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47

The change of numbering comes from commit 85d6725b ("libata:
make ata_print_id atomic") that changed lines like

	ap->print_id = ata_print_id++;
		to
	ap->print_id = atomic_inc_return(&ata_print_id);

As the latter behaves like ++ata_print_id, we must initialize
it to zero to start the numbering from one.
Signed-off-by: NTero Roponen <tero.roponen@gmail.com>
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The Marvell 88SE9172 SATA controller (PCI ID 1b4b 917a) already worked
once it was detected, but was missing an ahci_pci_tbl entry.

Boot tested on a Gigabyte Z68X-UD3H-B3 motherboard.
Signed-off-by: NMatt Johnson <johnso87@illinois.edu>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit d9027470("[libata] Add ATA transport class") introduced
ATA_EFLAG_OLD_ER to mark entries in the error ring as cleared.

But ata_count_probe_trials_cb() didn't check this flag and it still
counts the old error history. So wrong probe trials count is returned
and it causes problem, for example, SATA link speed is slowed down from
3.0Gbps to 1.5Gbps.

Fix it by checking ATA_EFLAG_OLD_ER in ata_count_probe_trials_cb().

Cc: stable <stable@vger.kernel.org> # 2.6.37+
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

While testing with the intel_infoframes tool on gen4, I see that when
video DIP is disabled, what we write to the DATA memory is not exactly
what we read back later.

This regression has been introduce in

commit 64a8fc01
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Thu Sep 22 11:16:00 2011 +0530

    drm/i915: fix ILK+ infoframe support

That commit was setting VIDEO_DIP_CTL to 0 when initializing, which
caused the problem.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43947
Cc: stable@kernel.org
Tested-by: NYang Guang <guang.a.yang@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: Pimped commit message by using the usual commit citation
layout.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We should initialise this to 0 really to avoid getting false positives.

Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit
bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5).
gp->asleep_wol remains 0 and the machine never wakes up.  Fixed by casting
gp->wake_on_lan to bool.  Tested on an iBook G4.
Signed-off-by: NGerard Lledo <gerard.lledo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If register_netdev returns failure, the dev->interrupt and
its transfer buffer should be released, so just fix it.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The transfer buffer of dev->interrupt is allocated in .probe path,
but not freed in .disconnet path, so mark the interrupt URB as
URB_FREE_BUFFER to free the buffer when the URB is destroyed.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Match the correct information which is DMI_PRODUCT_NAME instead of DMI_BOARD_NAME
See dmidecode information on launchpad for both thin client:

https://bugs.launchpad.net/ubuntu/+source/linux/+bug/911920
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/911916Signed-off-by: NMarc Gariepy <mgariepy@ubuntu.com>
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On SandyBridge IPS was entirely implemented in hardware and not reliant
on the driver monitoring power consumption and feeding back desired run
states, so the hardware is able to adapt quicker and more flexibly. Which
is a huge relief for us as we no longer have to carry empirically
derived magic algorithms.

Yet despite the advance in technology, the driver was still doing its
IPS polling on all machines. Restrict it to the only supported hardware,
Clarkdale/Arrandale.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NAndrey Rahmatullin <wrar@wrar.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49025Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We only execute intel_decrease_pllclock for pre-PCH hardware, typically
gen4 mobiles. However, in the variable declaration we did read from the
non-PCH DPLL register, quite naughty and detected by SandyBridge.
Reported-and-tested-by: NAndrey Rahmatullin <wrar@wrar.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49025Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.

Cc: <stable@vger.kernel.org> # v3.3
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1547) rearranges the Power Management parts of the
ehci-tegra driver to match the conventions used in other EHCI platform
drivers.  In particular, the controller should not be powered down by
the root hub's suspend routine; the controller's power level should be
managed by the controller's own PM methods.

The end result of the patch is that the standard ehci_bus_suspend()
and ehci_bus_resume() methods can be used instead of special-purpose
routines.  The driver now uses the standard dev_pm_ops methods instead
of legacy power management.  Since there is no supported wakeup
mechanism for the controller, runtime suspend is forbidden by default
(this can be overridden via sysfs, if desired).

These adjustments are needed in order to make ehci-tegra compatible
with recent changes to the USB core.  The core now checks the root
hub's status following bus suspend; if the controller is automatically
powered down during bus suspend then the check will fail and the root
hub will be resumed immediately.  Doing the controller power-down in a
separate method avoids this problem.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixing the locking accidentally replaced a race in the scroll
lock handling with a deadlock. Turn it back into a race for
now.

The basic problem is that there are two paths into the tty
stop/start helpers. One via the tty layer ^S/^Q handling
where we need to take the kbd_event_lock and one via the
special keyboard handler for fn_hold where we already hold
it. Probably we need to split out into a separate LED lock
but for now just go back to the race as it's a bit close
to release.
Reported-by: NClemens Ladisch <clemens@ladisch.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.

Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.

Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: NMirko Lindner <mlindner@marvell.com>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPU core ID is used to index the core_data[] array. The core ID is, however, not
sequential; 10-core CPUS can have a core ID as high as 25. Increase the limit to
32 to be able to deal with current CPUs.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NDurgadoss R <durgadoss.r@intel.com>

coretemp tries to access core_data array beyond bounds on cpu unplug if
core id of the cpu if more than NUM_REAL_CORES-1.

BUG: unable to handle kernel NULL pointer dereference at 000000000000013c
IP: [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
PGD 673e5a067 PUD 66e9b3067 PMD 0
Oops: 0000 [#1] SMP
CPU 79
Modules linked in: sunrpc cpufreq_ondemand acpi_cpufreq freq_table mperf bnep bluetooth rfkill ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter nf_conntrack_ipv4 nf_defrag_ipv4 ip6_tables xt_state nf_conntrack coretemp crc32c_intel asix tpm_tis pcspkr usbnet iTCO_wdt i2c_i801 microcode mii joydev tpm i2c_core iTCO_vendor_support tpm_bios i7core_edac igb ioatdma edac_core dca megaraid_sas [last unloaded: oprofile]

Pid: 3315, comm: set-cpus Tainted: G        W    3.4.0-rc5+ #2 QCI QSSC-S4R/QSSC-S4R
RIP: 0010:[<ffffffffa00159af>]  [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
RSP: 0018:ffff880472fb3d48  EFLAGS: 00010246
RAX: 0000000000000124 RBX: 0000000000000034 RCX: 00000000ffffffff
RDX: 0000000000000000 RSI: 0000000000000046 RDI: 0000000000000246
RBP: ffff880472fb3d88 R08: ffff88077fcd36c0 R09: 0000000000000001
R10: ffffffff8184bc48 R11: 0000000000000000 R12: ffff880273095800
R13: 0000000000000013 R14: ffff8802730a1810 R15: 0000000000000000
FS:  00007f694a20f720(0000) GS:ffff88077fcc0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 000000000000013c CR3: 000000067209b000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process set-cpus (pid: 3315, threadinfo ffff880472fb2000, task ffff880471fa0000)
Stack:
 ffff880277b4c308 0000000000000003 ffff880472fb3d88 0000000000000005
 0000000000000034 00000000ffffffd1 ffffffff81cadc70 ffff880472fb3e14
 ffff880472fb3dc8 ffffffff8161f48d ffff880471fa0000 0000000000000034
Call Trace:
 [<ffffffff8161f48d>] notifier_call_chain+0x4d/0x70
 [<ffffffff8107f1be>] __raw_notifier_call_chain+0xe/0x10
 [<ffffffff81059d30>] __cpu_notify+0x20/0x40
 [<ffffffff815fa251>] _cpu_down+0x81/0x270
 [<ffffffff815fa477>] cpu_down+0x37/0x50
 [<ffffffff815fd6a3>] store_online+0x63/0xc0
 [<ffffffff813c7078>] dev_attr_store+0x18/0x30
 [<ffffffff811f02cf>] sysfs_write_file+0xef/0x170
 [<ffffffff81180443>] vfs_write+0xb3/0x180
 [<ffffffff8118076a>] sys_write+0x4a/0x90
 [<ffffffff816236a9>] system_call_fastpath+0x16/0x1b
Code: 48 c7 c7 94 60 01 a0 44 0f b7 ac 10 ac 00 00 00 31 c0 e8 41 b7 5f e1 41 83 c5 02 49 63 c5 49 8b 44 c4 10 48 85 c0 74 56 45 31 ff <39> 58 18 75 4e eb 1f 49 63 d7 4c 89 f7 48 89 45 c8 48 6b d2 28
RIP  [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
 RSP <ffff880472fb3d48>
CR2: 000000000000013c
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' removes the include for
linux/gpio.h from omap-usb-host.c. This include indirectly includes plat/cpu.h
which is required by omap-usb-host.c. Fix the build breakage by including
it directly.
Acked-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Acked-by: NKevin Hilman <khilman@ti.com>
Tested-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NRuss Dill <Russ.Dill@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The driver calls cxgb_vlan_mode() from init_one().  This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets().  So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.

This was found because of the lockdep warning:

    INFO: trying to register non-static key.
    the code is fine but needs lockdep annotation.
    turning off the locking correctness validator.
    Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
    Call Trace:
     [<ffffffff8106e767>] register_lock_class+0x108/0x2d0
     [<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
     [<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
     [<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
     [<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
     [<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
     [<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
     [<ffffffff81042206>] do_work_for_cpu+0x10/0x22
     [<ffffffff810482de>] kthread+0xa1/0xa9
     [<ffffffff8138e234>] kernel_thread_helper+0x4/0x10

Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was freeing memory in shutdown instead of remove.  As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver.  This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: NSamuel Liao <samuelliao@tencent.com>
Signed-off-by: NShan Wei <davidshan@tencent.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.

Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

also explicitly set the phy to advertise 1000 speeds
Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d9460920Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O.  Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.

Without this patch sysfs reports the cable as present

flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1

while it's not:

flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>