All other host controllers who want aligned buffers for DMA do it a
certain way.  Let's do that too instead of working behind the USB core's
back.  This makes our interrupt handler not take forever and also rips
out a lot of code, simplifying things a bunch.

This also has the side effect of removing the 65535 max transfer size
limit.

NOTE: The actual code to allocate the aligned buffers is ripped almost
completely from the tegra EHCI driver.  At some point in the future we
may want to add this functionality to the USB core to share more code
everywhere.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

In (usb: dwc2: reset dwc2 core before dwc2_get_hwparams()) we added an
extra reset to the probe path for the dwc2 USB controllers.  This
allowed proper detection of parameters even if the firmware had already
used the USB part.

Unfortunately, this extra reset is quite slow and is affecting boot
speed.  We can avoid the double-reset by skipping the extra reset that
would happen just after the one we added.  Logic that explains why this
is safe:

* As of the CL mentioned above, we now always call dwc2_core_reset() in
  dwc2_driver_probe() before dwc2_hcd_init().

* The only caller of dwc2_hcd_init() is dwc2_driver_probe(), so we're
  guaranteed that dwc2_core_reset() was called before dwc2_hdc_init().

* dwc2_hdc_init() is the only caller that passes an irq other than -1 to
  dwc2_core_init().  Thus if dwc2_core_init() is called with an irq
  other than -1 we're guaranteed that dwc2_core_reset was called before
  dwc2_core_init().

...this allows us to remove the dwc2_core_reset() in dwc2_core_init() if
irq is not < 0.

Note that since "irq" wasn't used in the function dwc2_core_init()
anyway and since select_phy was always set at exactly the same times we
could avoid the reset, we remove "irq" and rename "select_phy" to
"initial_setup" and adjust the callers accordingly.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The dwc2_hcd_reset_func() function is only ever called directly by a
delayed work function.  As such no locks are already held when the
function is called.

Doing a read-modify-write of CPU registers and setting fields in the
main hsotg data structure is a bad idea without locks.  Let's add
locks.

The bug was found by code inspection only.  It turns out that the
dwc2_hcd_reset_func() is only ever called today if the
"host_support_fs_ls_low_power" parameter is enabled and no code in
mainline enables that parameter.  Thus no known issues in mainline are
fixed by this patch, but it's still probably wise to fix the function.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If you've got your interrupt signals bouncing a bit as you insert your
USB device, you might end up in a state when the device is connected but
the driver doesn't know it.

Specifically, the observed order is:
 1. hardware sees connect
 2. hardware sees disconnect
 3. hardware sees connect
 4. dwc2_port_intr() - clears connect interrupt
 5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()

Now you'll be stuck with the cable plugged in and no further interrupts
coming in but the driver will think we're disconnected.

We'll fix this by checking for the missing connect interrupt and
re-connecting after the disconnect is posted.  We don't skip the
disconnect because if there is a transitory disconnect we really want to
de-enumerate and re-enumerate.

Notes:
1. As part of this change we add a "force" parameter to
   dwc2_hcd_disconnect() so that when we're unloading the module we
   avoid the new behavior.  The need for this was pointed out by John
   Youn.
2. The bit of code needed at the end of dwc2_hcd_disconnect() is
   exactly the same bit of code from dwc2_port_intr().  To avoid
   duplication, we refactor that code out into a new function
   dwc2_hcd_connect().
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Kmem caches help to get correct boundary for descriptor buffers
which need to be 512 bytes aligned for dwc2 controller.
Two kmem caches are needed for generic descriptors and for
hs isochronous descriptors which doesn't have same size.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use Streaming DMA mappings to handle cache coherency of frame list and
descriptor list. Cache are always flushed before controller access it
or before cpu access it.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As descriptor dma mode does not support split transfers, it can't be
enabled for high speed devices. Add a core parameter to enable it for
full speed devices.

Ensure frame list and descriptor list are correctly freed during
disconnect.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In commit 734643df ("usb: dwc2: host: add flag to reflect bus
state") we changed dwc2_port_suspend() not to set the lx_state
anymore (instead it sets the new bus_suspended variable).  This
introduced a bug where we would fail to detect device insertions if:

1. Plug empty hub into dwc2
2. Plug USB flash drive into the empty hub.
3. Wait a few seconds
4. Unplug USB flash drive
5. Less than 2 seconds after step 4, plug the USB flash drive in again.

The dwc2_hcd_rem_wakeup() function should have been changed to look at
the new bus_suspended variable.

Let's fix it.  Since commit b46146d5 ("usb: dwc2: host: resume root
hub on remote wakeup") talks about needing the root hub resumed if the
bus was suspended, we'll include it in our test.

It appears that the "port_l1_change" should only be set to 1 if we were
in DWC2_L1 (the driver currently never sets this), so we'll update the
former "else" case based on this test.

Fixes: 734643df ("usb: dwc2: host: add flag to reflect bus state")
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NGregory Herrero <gregory.herrero@intel.com>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

From code inspection, it appears to be unsafe to do a read-modify-write
of PCGCTL in dwc2_port_resume().  Let's make sure the spinlock is held
around this operation.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Make sure there are no requests pending on ep0 before reinitializing
core. Otherwise, dwc2_hsotg_enqueue_setup will fail afterwards.

Also, take hsotg->lock before calling
dwc2_hsotg_core_init_disconnected() from dwc2_conn_id_status_change()
as dwc2_hsotg_complete_request() expect lock to be held.
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On a disconnect, dwc2 will kill all remaining urbs from qh list.
urbs are given back to hcd with -ETIMEDOUT status.
Some usb device driver, like mass storage, will unlink all urbs
using usb_hcd_unlink_urb when receiving a negative status different
from -ECONNRESET.
The following flow will then happen:
dwc2_hcd_disconnect()
-> dwc2_kill_all_urbs() try to kill first pending urb.
-> dwc2_host_complete(-ETIMEDOUT)
-> usb_hcd_giveback_urb(-ETIMEDOUT)
-> sg_complete()
-> usb_unlink_urb()
	-> usb_put_dev(urb->dev)
-> dwc2_kill_all_urbs() try to kill next pending urb.
-> dwc2_host_complete(-ETIMEDOUT)
-> usb_hcd_giveback_urb(-ETIMEDOUT)
-> NULL pointer dereferencing because urb->dev has been freed for all
urbs of this device.

The root cause of this NULL pointer is to call call usb_unlink_urb()
while we are killing all urbs. To avoid this return urb with
-ECONNRESET status

This issue usually happens while removing mass storage device during
transfer.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Print urb->iso_frame_desc.status after it has been updated using
dwc2_hcd_urb_get_iso_desc_status().
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some high speed mass storage devices fail to enumerate with following
error:

Cannot enable port %i.  Maybe the USB cable is bad?

This happens only when the device is plugged while the controller
is in hibernation state. After exiting hibernation, the controller
detects the device as a low speed device and fail to enumerate it.

Problem occurs only if HPRT0.PWR bit is programmed in a too short
delay after exiting hibernation. Dumping hprt register in
_dwc2_hcd_resume() directly after dwc2_exit_hibernation() shows that
HPRT0.LNSTS (D+/D- level) becomes valid approximately 2ms after
exiting hibernation.

Since dwc2_exit_hibernation() is called from atomic context, move the
delay out of this function.

Delay value is experimental and not mentioned in Synopsys
documentation. To be on the safe side 3ms delay is used.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Disable host interrupts before synchronising dwc2 irq.
So that interrupts are not generated once controller is stopped.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case controller is asked to stop while devices are connected,
disconnect all devices and clean up before stopping.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Port can be resumed in bus_resume callback.
In this case, there is no need to drive resume a second time
when hcd ask for it.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During hcd initialization, hardware accessible flag and lx_state must
be reset to the working state since controller is powered at this stage.

Same logic applied for stop callback.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Disable controller power and enter hibernation when usb bus is
suspended. A phy driver is required to disable the power of the
controller and detect remote-wakeup or disconnection since the
controller will not be able to detect these in this state.

Once the phy driver detects bus activity, it must call
usb_hcd_resume_root_hub.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

lx_state must be used to reflect controller power state only and not
bus state. Thus add a flag to track state during bus suspend.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

port resume sequence may be used in different places. Create a
function to handle it. Make hprt0 read-modify-write atomic and
clear HPRT0_SUSP for both writes as it is a "read, write-set,
and self-clear (R_WS_SC)" bit. Since the lock is released
between the writes, read hprt0 again.

Since the phy clock is stopped in dwc2_port_suspend(), enable it
here and remove the PCGCTL write from dwc2_hcd_hub_control()
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.

This patch is necessary to access dwc2 registers correctly on big-endian
systems such as the mips based SoCs made by Lantiq. Then dwc2 can be
used to replace ifx-hcd driver for Lantiq platforms found e.g. in
OpenWrt.

The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h

Some files were then hand-edited to fix checkpatch.pl warnings about
too long lines.
Signed-off-by: NAntti Seppälä <a.seppala@gmail.com>
Signed-off-by: NVincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To avoid sleep while atomic bugs, allocate qtd before calling
dwc2_hcd_urb_enqueue. No need to pass mem_flags to
dwc2_hcd_urb_enqueue any more as no memory allocations are done in it.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To avoid sleep while atomic bugs, allocate qh before calling
dwc2_hcd_urb_enqueue. qh pointer can be used directly now instead of
passing ep->hcpriv as double pointer.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit db62b9a8 (usb: dwc2: host: don't
use dma_alloc_coherent with irqs disabled)
introduced a build warning by using NULL
as an integer. Fix that by just using 0 instead
of NULL.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As dwc2 pci module is now exporting dwc2 platform device, include
platform.o in dwc2-y and remove USB_DWC2_PLATFORM configuration
option. Driver will be built as two modules, dwc2.ko and dwc2_pci.ko.
dwc2.ko is the new platform driver.

Remove all EXPORT_SYMBOL_GPL as they are not needed any more.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add support for SetPortFeature(PORT_TEST) for root port.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NJingwu Lin <jingwu.lin@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Align buffer must be allocated using kmalloc since irqs are disabled.
Coherency is handled through dma_map_single which can be used with irqs
disabled.
Reviewed-by: NJulius Werner <jwerner@chromium.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During urb_enqueue, if the urb can't be queued to the endpoint,
the urb is freed without any spinlock protection.
This leads to memory corruption when concurrent urb_dequeue try to free
same urb->hcpriv.
Thus, ensure the whole urb_enqueue in spinlocked.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Update controller state to indicate suspend entry.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If phy driver is present register hcd handle to it.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

So the parameters can be used in both host and gadget modes.
Also consolidate param functions in the core.h
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

msleep(USB_RESUME_TIMEOUT) must be done when the controller drives
the resume. This is true after HPRT0_RES is written.
Moreover, restore the delay after controller power is up.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure we're using the new macro, so our
resume signaling will always pass certification.

Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix  using the  bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value  is #define'd in <linux/usb/ch11.h>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the HCD is disconnected, the DMA transfers still in-flight were cleaned-up
but the count of available DMA channels (e.g. available_host_channels) was not
reset.
The pool of DMA channels can be depleted when doing unclean
disconnection of USB peripherals, and reaches the point where no
transfer was possible until the next reboot/reload of the driver.

Tested by putting a programmable USB mux on the port and randomly
plugging/unpluging a USB HUB with USB mass-storage key, USB-audio and
USB-ethernet dongle connected to its downstream ports, and also doing the
disconnection early while the devices are still enumerating to get more URBs
in-flight.
After the patch, the devices are still enumerating after thousands of cycles,
while the port was totally dead before.
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add a flag to request physical reset of the controller when
s3c_hsotg_core_init_disconnected is called.
During the usb reset, controller must not be fully reconfigured and
resetted. Else this leads to shorter chirp-k duration during
enumeration.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When a remote wakeup happens during bus_suspend, hcd needs to resume
its root hub.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix  using the  bare number  to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix  using the  bare number  to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>