IR is the last piece that still is handled natively. This patch converts
it into a sub-device module like all other sub-devices. It mainly moves
code and doesn't change semantics.

We also implicitly sync IR data on ir_to_input3 now so the explicit
input_sync() calls are no longer needed.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Accelerometer data is very similar to KEYS handling. Therefore, convert
all ACCEL related handling into a sub-device module similar to KEYS.

This doesn't change any semantics but only moves code over to
wiimote-modules.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Each of the 4 LEDs may be supported individually by devices. Therefore,
we need one module for each device. To avoid code-duplication, we simply
pass the LED ID as "arg" argument to the module loading code.

This just moves the code over to wiimote-module. The semantics stay the
same as before.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This introduces a new sub-device module for the BATTERY handlers. It
moves the whole power_supply battery handling over to wiimote-modules.

This doesn't change any semantics or ABI but only converts the battery
handling into a sub-device module.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This introduces the first sub-device modules by converting the KEYS and
RUMBLE sub-devices into wiimote modules. Both must be converted at once
because they depend on the built-in shared input device.

This mostly moves code from wiimote-core to wiimote-modules and doesn't
change any semantics or ABI.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

To avoid loading all sub-device drivers for every Wii Remote, even though
the required hardware might not be available, we introduce a module layer.

The module layer specifies which sub-devices are available on each
device-type. After device detection, we only load the modules for the
detected device. If module loading fails, we unload everything and mark
the device as WIIMOTE_DEV_UNKNOWN. As long as a device is marked as
"unknown", no sub-devices will be used and the device is considered
unsupported.

All the different sub-devices, including KEYS, RUMBLE, BATTERY, LEDS,
ACCELEROMETER, IR and more will be ported in follow-up patches to the new
module layer.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Our output queue is asynchronous but synchronous reports may wait for a
response to their request. Therefore, wake them up unconditionally if an
output report couldn't be sent. But keep the report ID intact so we don't
incorrectly assume our request succeeded.

Note that the underlying connection is required to be reliable and does
retransmission itself. So it is safe to assume that if the transmission
fails, the device is in inconsistent state. Hence, we abort every request
if any output report fails. No need to verify which report failed.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Battery reports are sent along every status report of the Wii Remote.
So chances are pretty high that we have an up-to-date battery
cache at any time. Therefore, initialize the battery-cache to 100% and
then return battery values from the cache if the query fails.

This works around a power_supply limitation in that it requires us to be
able to query the device during power_supply registration and
removal. Otherwise, "add" or "remove" udev events are not sent. If
we answer these requests from our cache instead, we avoid dropping these
events and no longer cause warnings printed.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Nintendo produced many different devices that are internally based on the
Wii Remote protocol but provide different peripherals. To support these
devices, we need to schedule a device detection during initialization.

Device detection includes requesting a status report, reading extension
information and then evaluating which device we may be dealing with.

We currently detect gen1 and gen2 Wii Remote devices. All other devices
are marked as generic devices. More detections will be added later.

In followup patches we will be using these device IDs to control which
peripherals to initialize. For instance if a device is known to have no IR
camera, there is no need to provide the IR input device nor trying to
access IR registers. In fact, there are 3rd party devices that break if we
try things like this (hurray!).

The init_worker will be scheduled whenever we get hotplug events. This
isn't implemented, yet and will be added later. However, we need to make
sure that this worker can be called multiple times.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

We need constant I/O to keep the state up-to-date and not miss any
packets. Hence, call hid_hw_open() during setup and hid_hw_close() during
destruction.

These are no-ops for Bluetooth HIDP, but lets be safe.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The output queue is independent of the other wiimote modules and can run
on its own. Therefore, move its members into a separate struct so we don't
run into name collisions with other modules.

This is only a syntactic change that renames all queue members to queue.*.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The hid-wiimote driver supports more than the Wii Remote. Nintendo
produced many devices based on the Wii Remote, which have extension
devices built-in. It is not clear to many users, that these devices have
anything in common with the Wii Remote, so fix the driver description.

This also updates the copyright information for the coming hotplugging
rework.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

commit 6cd2c7db (videomode: videomode_from_timing work) changed the name of
the function from videomode_from_timing() to videomode_from_timings().

commit 32ed6ef1 (videomode: create enum for videomode's display flags) changed
the 'data_flags' field in videomode structure to 'flags'

Adapt to these changes in order to fix the following errors:

drivers/video/mxsfb.c:761:3: error: too many arguments to function 'videomode_from_timing'
drivers/video/mxsfb.c:761:7: error: void value not ignored as it ought to be
drivers/video/mxsfb.c:768:9: error: 'struct videomode' has no member named 'data_flags'
drivers/video/mxsfb.c:770:9: error: 'struct videomode' has no member named 'data_flags'

Also, select VIDEOMODE_HELPER instead of OF_VIDEOMODE, as this one is
deprecated.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>

When usb_create_hcd fail, we should call gxio_usb_host_destroy
Signed-off-by: NLibo Chen <libo.chen@huawei.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [extended to EHCI]

I get the following warning on boot:

------------[ cut here ]------------
WARNING: at drivers/base/core.c:575 device_create_file+0x9a/0xa0()
Hardware name:  -[8737R2A]-
Write permission without 'store'
...
</snip>

Drilling down, this is related to dynamic channel ce_count attribute
files sporting a S_IWUSR mode without a ->store() function. Looking
around, it appears that they aren't supposed to have a ->store()
function. So remove the bogus write permission to get rid of the
warning.
Signed-off-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: <stable@vger.kernel.org> # 3.[89]
[ shorten commit message ]
Signed-off-by: NBorislav Petkov <bp@suse.de>

A race condition exists when registering the first watchdog device.
Sequence of events:

- watchdog_register_device calls watchdog_dev_register
- watchdog_dev_register creates the watchdog misc device by calling
  misc_register.
  At that time, the matching character device (/dev/watchdog0) does not yet
  exist, and old_wdd is not set either.
- Userspace gets an event and opens /dev/watchdog
- watchdog_open is called and sets wdd = old_wdd, which is still NULL,
  and tries to dereference it. This causes the kernel to panic.

Seen with systemd trying to open /dev/watchdog immediately after
it was created.
Reported-by: NArkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NArkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

reproduce steps
 1. flood ping from other machine
 	ping -f -s 41000 IP
 2. run below script
    while [ 1 ]; do ethtool -s eth0 autoneg off;
    sleep 3;ethtool -s eth0 autoneg on; sleep 4; done;

You can see oops in one hour.

The reason is fec_restart clear BD but NAPI may use it.
The solution is disable NAPI and stop xmit when reset BD.
disable NAPI may sleep, so fec_restart can't be call in
atomic context.
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Tested-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function ptp_clock_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return -ENOMEM in the irlap_open() error handling case instead
of 0(overwrite to 0 by bfin_sir_startup()), as done elsewhere in this
function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

of_mdiobus_register creates a phy_device even if get_phy_device failed
to create it previously. This causes indefinite polling on non-existent
PHYs. This fix makes of_mdio_register rely on get_phy_device to
properly create the device or fail otherwise.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver and firmware sync up through SYNC messages, and the
firmware's affirmative reply to these SYNC messages appears to be the
"Reset" indication received via the status interrupt endpoint.  Thus the
driver needs the status interrupt endpoint always active so that the
Reset indication can be received even if the netdev is closed, which is
the case right after device insertion.

If the Reset indication is not received by the driver, it continues
sending SYNC messages to the firmware, which crashes about 10 seconds
later and the device stops responding.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers (sierra_net) need the status interrupt URB
active even when the device is closed, because they receive
custom indications from firmware.  Add functions to refcount
the status interrupt URB submit/kill operation so that
sub-drivers and the generic driver don't fight over whether
the status interrupt URB is active or not.

A sub-driver can call usbnet_status_start() at any time, but
the URB is only submitted the first time the function is
called.  Likewise, when the sub-driver is done with the URB,
it calls usbnet_status_stop() but the URB is only killed when
all users have stopped it.  The URB is still killed and
re-submitted for suspend/resume, as before, with the same
refcount it had at suspend.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Acked-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A rebranded Novatel E371 for AT&T's LTE bands.  qmi_wwan should drive this
device, while cdc_ether should ignore it.  Even though the USB descriptors
are plain CDC-ETHER that USB interface is a QMI interface.

Cc: <stable@vger.kernel.org>
Signed-off-by: NDan Williams <dcbw@redhat.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be_close() followed by be_clear() is called as a part of cleanup in the
EEH/AER flow.  This patch stops TX in be_close() before cleaning/freeing
up the TX queues in be_clear(). This prevents be_xmit() from being called
while TX queues no longer exist.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While cleaning RX queues, the CQ DB may be rung several times (with rearm)
while waiting for the flush compl. Each CQ-notify with rearm can result in
an event. The EQ may get full resulting in a HW error.

Fix this by not re-arming the CQ while notifying a valid completion.
Also, there's no need to wait for 1ms after destroying RXQ, as the code in
be_rx_cq_clean() waits for the flush compl to arrive.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The buffer size for a FW cmd request must be big enough to fit the response,
else the cmd fails. For GET_MAC_LIST cmd, though the memory allocated for
the cmd is big enough to fit the response, the payload_len value in the
WRB hdr is being set to the request length only.
Fix this for GET_MAC_LIST cmd.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the PF driver calls pci_enable_sriov(), the VFs may be probed
inline before the call returns. So, the resources required for all VFs
must be provisioned by the PF driver *before* calling pci_enable_sriov();
else, VF probe will fail.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have registered platform device when module init, and
need unregister it when module exit.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

Add definitions for the three Firmware Activate actions, and change the
SCSI translation code to construct the command into a temporary variable
instead of translating the endianness back-and-forth.
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: NVishal Verma <vishal.l.verma@linux.intel.com>

Many of the bits in the Controller Configuration register may only be
modified when the Enable bit is clear.  Clearing them at the same time
as the Enable bit might be OK, but let's play it safe and only touch the
Enable bit.
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: NKeith Busch <keith.busch@intel.com>

A recent update to the specification makes it clear that the host
is expected to wait for the device to acknowledge the Enable bit
transitioning to 0 as well as waiting for the device to acknowledge a
transition to 1.
Reported-by: NKhosrow Panah <Khosrow.Panah@idt.com>
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: NKeith Busch <keith.busch@intel.com>

This change fixes a problem introduced by recent commit c34c82bc
(ACPICA: Predefine names: Add allowed argument types to master info
table) in 20130328 where _INI methods are no longer executed properly
because of a memory block that is not initialized properly.  ACPICA
BZ1016. Tomasz Nowicki <tomasz.nowicki@linaro.org>

References: https://bugs.acpica.org/show_bug.cgi?id=1016Signed-off-by: NTomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Fixes a possible memory leak in the error exit path introduced by
recent commit 388a9902 ("ACPICA: _OSI Support: handle any errors from
acpi_os_acquire_mutex()").

[rjw: Changelog]
Signed-off-by: NJung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Can only happen under these conditions: 1) The DSDT version is 1,
meaning integers are 32-bits.  2) The field is between 33 and 64
bits long.

It applies cleanly back to ACPICA 20100806+ (Linux v2.6.37+).
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Cc: 2.6.37+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Faster kernel compiles by way of fewer unnecessary includes.

[akpm@linux-foundation.org: fix fallout]
[akpm@linux-foundation.org: fix build]
Signed-off-by: NKent Overstreet <koverstreet@google.com>
Cc: Zach Brown <zab@redhat.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: N"Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cancelling kiocbs requires adding them to a per kioctx linked list,
which is one of the few things we need to take the kioctx lock for in
the fast path.  But most kiocbs can't be cancelled - so if we just do
this lazily, we can avoid quite a bit of locking overhead.

While we're at it, instead of using a flag bit switch to using ki_cancel
itself to indicate that a kiocb has been cancelled/completed.  This lets
us get rid of ki_flags entirely.

[akpm@linux-foundation.org: remove buggy BUG()]
Signed-off-by: NKent Overstreet <koverstreet@google.com>
Cc: Zach Brown <zab@redhat.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: N"Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>