* Filter out "default" transfer mode values (0x00 - default PIO mode,
  0x01 - default PIO mode w/ IORDY disabled) in write handler for obsoleted
  /proc/ide/hd?/settings:current_speed setting.

  Allowing "default" transfer mode values is a dangerous thing to do as
  we don't support programming controller to the "default" transfer mode
  and devices often use different values for the default and maximum PIO
  mode (i.e. PIO2 default and PIO4 maximum) so the controller will stay
  programmed for higher PIO mode while device will use the lower PIO mode.

  There is no functionality loss as by using special IOCTLs device can
  still be programmed to "default" transfer modes (it is only useful for
  debugging/testing purposes anyway).

* Remove no longer needed IDE_HFLAG_ABUSE_SET_DMA_MODE host flag, it was
  previously used by few host drivers to program the controller to PIO0
  timings for "default" transfer mode == 0x01 (although some host drivers
  would program invalid PIO timings instead).

* Cleanup ide_set_xfer_rate() and add BUG_ON().
Suggested-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Filter out invalid transfer mode values (0x02-0x07) in write handler
for obsoleted /proc/ide/hd?/settings:current_speed setting.

While at it:

* Use XFER_UDMA_6 define.
Suggested-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Lets remove dead Virtual DMA support for now so it doesn't clutter
core IDE code (it can be bring back when there is a need for it):

* Remove IDE_HFLAG_VDMA host flag.

* Remove ide_drive_t.vdma flag.

* cs5520.c: remove stale FIXMEs, cs5520_dma_host_set() and cs5520_dma_ops
  (also there is no longer a need to set IDE_HFLAG_NO_ATAPI_DMA).

There should be no functional changes caused by this patch.

Cc: TAKADA Yoshihito <takada@mbf.nifty.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Alan Cox has noticed some time ago that hpt34x is broken
(http://lkml.org/lkml/2007/7/3/257):

"No the old driver doesn't even do that. It starts up. It spuriously
adjusts some non writable PCI BAR registers, prints a message about
resources being in use already then exits."
Reported-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove no longer needed ->INB, ->OUTB and ->OUTBSYNC methods.

Then:

* Remove no longer used default_hwif_[mm]iops() and ide_[mm_]outbsync().

* Cleanup SuperIO handling in ns87415.c.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_read_bcount_and_ireason() helper and use it instead of ->INB
in {cdrom_newpc,ide_pc}_intr().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_read_ireason() helper and use instead of ->INB for reading
ATAPI Interrupt Reason register.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_read_device() helper and convert do_probe() to use it
instead of ->INB.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_IN_FEATURE taskfile flag for reading Feature
  register and handle it in ->tf_read.

* Convert ide_read_error() to use ->tf_read instead of ->INB,
  then uninline and export it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Convert SELECT_DRIVE() to use ->tf_load instead of ->OUTB.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Convert actual_try_to_identify() to use ->tf_load instead of ->OUTB.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Convert ide_config_drive_speed() to use ->tf_load instead of ->OUTB.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Write ATA Feature register before ATA Sector Count register as
a preparation to use ->tf_load in ide_config_drive_speed().

This change shouldn't affect anything (just an usual paranoia).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->set_irq method for setting nIEN bit of ATA Device Control
register and use it instead of ide_set_irq().

While at it:

* Use ->set_irq in init_irq() and do_reset1().

* Don't use HWIF() macro in ide_check_pm_state().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove ide_read_altstatus() inline helper.

* Add ->read_altstatus method for reading ATA Alternate Status
  register and use it instead of ->INB.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove ide_read_status() inline helper.

* Add ->read_status method for reading ATA Status register
  and use it instead of ->INB.

While at it:

* Don't use HWGROUP() macro.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->exec_command method for writing ATA Command register
and use it instead of ->OUTBSYNC.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out simplex handling from ide_pci_dma_base() to
  ide_pci_check_simplex().

* Set hwif->dma_base early in ->init_dma method / ide_hwif_setup_dma()
  and reset it in ide_init_port() if DMA initialization fails.

* Use ->read_sff_dma_status instead of ->INB in ide_pci_dma_base().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Export sff_dma_ops and then remove ide_setup_dma().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use ->dma_base + offset instead of ->dma_{status,command}
  and remove no longer needed ->dma_{status,command}.

While at it:

* Use ATA_DMA_* defines.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use I/O ops directly in ide_dma_host_set(), ide_dma_setup(),
ide_dma_start() and __ide_dma_end().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->read_sff_dma_status method for reading DMA Status register
and use it instead of ->INB.

While at it:

* Use inb() directly in ns87415.c::ns87415_dma_end().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add 'hw_regs_t **hws' argument to ide_device_add[_all]() and convert
  host drivers + ide_legacy_init_one() + ide_setup_pci_device[s]() to use
  it instead of calling ide_init_port_hw() directly.

  [ However if host has > 1 port we must still set hwif->chipset to hint
    consecutive ide_find_port() call that the previous slot is occupied. ]

* Unexport ide_init_port_hw().

v2:
* Use defines instead of hard-coded values in buddha.c, gayle.c and q40ide.c.
  (Suggested by Geert Uytterhoeven)

* Better patch description.

v3:
* Fix build problem in ide-cs.c. (Noticed by Stephen Rothwell)

There should be no functional changes caused by this patch.

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_pci_setup_ports() call out from do_ide_setup_pci_device()
  to ide_setup_pci_device[s]().

* Drop no longer needed idx argument from do_ide_setup_pci_device().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move ide_find_port() call to pmac_ide_setup_device().

While at it:

- fix return value (s/-ENODEV/-ENOENT/)

- add DRV_NAME define and use it to set name field of pmac_port_info

- use ide_find_port_slot() instead of ide_find_port()

- remove superfluous error message (ide_find_port_slot() takes care of it)

- drop IDE interface number from driver banner message (but include bus type)

v2:
* Build fix (thanks to Stephen Rothwell for noticing the issue).

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

v2/3:
* Build fixes from Stephen Rothwell.

v4:
* Fix ->noprobe setting. (From Benjamin Herrenschmidt)

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Pass pmif instead of hwif to pmac_ide_do_{suspend,resume}().

* Store pmif instead of hwif in ->driver_data.

* Use dev_get_drvdata() instead of ->hwif_data to obtain pmif.

v2:
* Build fixes from Stephen Rothwell.

There should be no functional changes caused by this patch.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.

Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure that each error condition during the execution of an
HDIO_DRIVE_RESET ioctl is actually reported to the calling process.
Also, unify the exit path of reset_pollfunc() when returning ide_stopped
since the need of ->port_ops->reset_poll() to be treated specially has
vanished (way back, it seems).
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove some code which has been made obsolete and hasn't worked properly
before anyway.  Part of the infrastructure may be reintroduced in a
follow up patch to implement a working command aborting facility.
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Currently, the code path executing an HDIO_DRIVE_RESET ioctl is broken
in various ways.  Most importantly, it is treated as an out of band
request in an illegal way which may very likely lead to system lock ups.
Use the drive's request queue to avoid this problem (and fix a locking
issue for free along the way).
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch moves hd.c to drivers/block/
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since the later move to drivers/block/ will break the link order,
the module_init() has to become a late_initcall().
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

After commit 80aa31cb
(ide: remove CONFIG_BLK_DEV_HD_IDE config option (take 2))
the indirection through BLK_DEV_HD_ONLY is no longer required.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This is a precaution just to make sure a new pc is clean when allocated.

There should be no functional change introduced by this patch.

[bart: ported it over IDE changes]
Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There's no need for this function since it is used only once.

[bart: ported it over IDE changes]
Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

As a nice side effect, this minimizes the IRQ handler execution time.

There should be no functionality change resulting from this patch.

[bart: remove extra newlines from ide_cd_do_request()]
Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

... by factoring out the rq preparation code into a separate
function called in the request routine.  As a nice side effect,
this minimizes the IRQ handler execution time.

There should be no functionality change resulting from this patch.

[bart: s/HWGROUP()/drive->hwif->hwgroup/ and remove extra newline]
Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>