Wait for the chip to be ready before any access to it. On the
Snowball platform we need to enable an external regulator before
the chip comes online, and then it happens that the device is
not yet ready at probe time, so let's wait for it.
Signed-off-by: NRobert Marklund <robert.marklund@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes sure that tx_packets/rx_bytes ifconfig counters are
updated even on NICs that don't provide hardware support for these
stats: they are now updated in software. For the sake of consistency,
we also now have tx_bytes updated in software (hardware counters
include ethernet CRC, and software doesn't account for it).

This reverts parts of:
 - "forcedeth: statistics optimization" (21828163)
 - "forcedeth: Improve stats counters" (0bdfea8b)
 - "forcedeth: remove unneeded stats updates" (4687f3f3)

Tested:
  pktgen + loopback (http://patchwork.ozlabs.org/patch/124698/)
  reports identical tx_packets/rx_packets and tx_bytes/rx_bytes.
Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While tracing down a connectivity problem on the temac I connected a
probe to the Cross bar irq, and it was triggered when doing
ifdown->ifup.

This is fixed once waiting for the indirect write to end. Since it is
not on the hot path there is no performance loss.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not enable the irq until the scatter gather registers are ready to
handle the data. Otherwise an irq from a packet send/received before
last close can lead to an access to an invalid memory region on the irq
handler.

Also, stop the dma engine on close.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To prevent the SBus driver for Sun Happy Meal cards from being loaded for
PCI cards utilizing the same chipset, a filter was added to the probe
function in commit 0b492fce.

The filter was implemented by checking the name of the parent node in
the OF tree. This patch extends this filter, so that the driver will
load on SBus systems that are based upon SBI SBus Bridges.
Signed-off-by: NKjetil Oftedal <oftedal@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link down would occur when reseting PHY. And it would take about 2 ~ 5 seconds
from link down to link up. If the delay of pm_schedule_suspend is not long enough,
the device would enter runtime_suspend before link up. After link up, the device
would wake up and reset PHY again. Then, you would find the driver keep in a loop
of runtime_suspend and rumtime_resume.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the following sparse warnings:
drivers/net/ethernet/nvidia/forcedeth.c:2113:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2155:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2227:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2271:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2986:20: warning: symbol 'addr' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2963:6: originally declared here
Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rx byte count was off; instead use the hardware's count.  Tx packet
count was counting pre-TSO packets; instead count on-the-wire packets.
Report hardware dropped frame count as rx_fifo_errors.

- The count of transmitted packets reported by the forcedeth driver
  reports pre-TSO (TCP Segmentation Offload) packet counts and not the
  count of the number of packets sent on the wire. This change fixes
  the forcedeth driver to report the correct count. Fixed the code by
  copying the count stored in the NIC H/W to the value reported by the
  driver.

- Count rx_drop_frame errors as rx_fifo_errors:
  We see a lot of rx_drop_frame errors if we disable the rx bottom-halves
  for too long.  Normally, rx_fifo_errors would be counted in this case.
  The rx_drop_frame error count is private to forcedeth and is not
  reported by ifconfig or sysfs.  The rx_fifo_errors count is currently
  unused in the forcedeth driver.  It is reported by ifconfig as overruns.
  This change reports rx_drop_frame errors as rx_fifo_errors.
Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function ndo_get_stats() updates most of the stats from hardware
registers, making the manual updates un-needed. This change removes
these manual updates. Main exception is rx_missed_errors which needs
manual update.

Another exception is rx_packets, still updated manually in this commit
to make sure this patch doesn't change behavior of driver. This will
be addressed by a future patch.
Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to avoid a race, accidentally acknowledging an interrupt that
we didn't notice and won't immediately process.  This is based solely
on code inspection; it is not known if there was an actual bug here.
Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When forcedeth module is unloaded, there exists a path that can lead
to mod_timer() after del_timer_sync(), causing an oops. This patch
short-circuits this unneeded path, which originates in
nv_get_ethtool_stats().

Tested:
  x86_64 16-way + 3 ethtool -S infinite loops + 100Mbps incoming traffic
  + rmmod/modprobe/ifconfig in a loop

Initial-Author: Salman Qazi <sqazi@google.com>
Discussion: http://patchwork.ozlabs.org/patch/123548/Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix compiler errors and warnings with CONFIG_PCI_IOV defined and not
defined.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to support other Optima types, introduced an accidental
regression that caused 88E8059 to come up in 10Mbit/sec.

The Yukon Optima supports a reverse auto-negotiation feature that
was incorrectly setup, and not needed. The feature could be used to
allow wake-on-lan at higher speeds. But doing it correctly would require
other changes to initialization.
Reported-by: NPavel Mateja <pavel@netsafe.cz>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i825xx and xscale are "sub" Kconfigs to NET_VENDOR_INTEL, so
NET_VENDOR_INTEL should contain ALL the dependencies of the
"sub" Kconfigs.

Same with 8390 is a "sub" Kconfig to NET_VENDOR_NATSEMI, so
NET_VENDOR_NATSEMI needs to contains ALL the dependencies.

Freescale Kconfig only had fs_enet as a sub Kconfig, and already
contained the needed dependencies, just cleaned up the dependencies.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.121.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During shutdown, it is impossible to reliably disable the timer and
reset_task threads.  Each thread can schedule the other, which leads to
shutdown code that chases its tail.

To fix the problem, this patch removes the ability of tg3_reset_task to
schedule a new timer thread.  To support this change, tg3_timer no
longer terminates itself, but rather goes into a polling mode.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible for multiple threads in the tg3 driver to each attempt to
schedule a run of tg3_reset_task().  The multiple tg3_reset_task
executions could all wind up on the same queue (and execute serially) or
wind up on the queues of another processor (which could execute in
parallel).  Either scenario is not what was truly desired.

This patch adds a new flag, TG3_FLAG_RESET_TASK_PENDING, and uses it to
determine whether or not to schedule another run of tg3_reset_task().
With the new flag comes two new functions to facilitate scheduling and
descheduling of tg3_reset_task().
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to attempt to obtain the PCI function number from
the device rather than accept the number handed by the kernel.  In
pass-through scenarios, the function number handed by the kernel may not
reflect the true function of the device.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug where the irq error cleanup path did not free all
the resources it allocated.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBen Li <benli@broadcom.com>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the error recovery resource unwind path, it is possible for the
driver to attempt to unmap a fragment that hadn't been mapped.  This
patch fixes the problem by correcting the "last" parameter supplied.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new 4k tx bd segmentation code had a bug in the error cleanup path.
If the driver did not map all the physical fragments, the abort path
would wind up advancing the producer index beyond the point where the
setup code stopped.  This would ultimately turn into a tx recovery error
where the driver would expect the skb pointer to be set when it isn't.
This patch fixes the problem, and then makes the code a little easier to
understand.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

APE mutex register blocks are shared by all ports of multiport devices.
For some mutexing purposes, each function is assigned their own
register.  For other cases, each function is assigned its own request
and grant bits of a single register.  For the latter cases, the tg3
driver is incorrectly allowing each function to use the same set of
grant / request bits.  This patch fixes the code so that each function
uses the appropriate bitset.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to detect UE in case of Lancer.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Indicate to HW that the CQ is cleaned up before posting new RX buffers.
This prevents the HW to go into CQ full error condition.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If user tries to disable multicast promiscous mode, the adapter remains
in this mode as resetting the multicast promiscous mode was missing
in RX filter command. Fixed this.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use cpu_to_le32() for mcast_num field in RX filter command as this
field is of type u32.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Returning the max traffic classes on get requests simplifies
user space configurations because applications will know
explicitly how many traffic classes can be used.

Typical switch implementations use 2 or 3 traffic classes
so this not seen often today. And user space can learn
the number of traffic classes by return codes but this
allows user space to configure ixgbe correctly at the
start.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes some issues found in the buffer read portion of
ixgbe_host_interface_command()

- use `bi` as the buffer index counter instead of `i`
- add conversion to native cpu byte ordering on register read
- fix conversion from bytes to dword
- use dword_len instead of buf_len when reading the register
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Wrap SR-IOV specific functions in CONFIG_PCI_IOV to avoid compiler
warnings.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_ieee_ets and ixgbe_ieee_pfc are intialized at
the same time. Do a check for both before configuring
IEEE802.1Qaz. Also max_frame was causing a sparse
warning resolved here as well.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

register_netdev() calls ndo_set_features() which may result in HW reset
which in turn will bring the laser back up.

This patch moves ixgbe_laser_tx_disable() below register_netdev()
in ixgbe_probe() to make sure laser is shut off on load.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Interface fails to obtain link on 82599 SFP in the following scenario:

1. Set advertised speed to GB:
ethtool -s eth0 advertise 0x20

2. Bring interface down
ip link set eth0 down

3. Issue any command that leads to a reset:
ethtool -t eth0

4. Bring link back up:
ip link set eth0 up

Following patch makes sure that the driver flaps the Tx laser every time
ixgbe_start_hw() is called, and not only when the speed is set.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PHY cable length unit detection was not using the correct
the correct PHY data variable for I347AT4.
Signed-off-by: NTomasz Kantecki <tomasz.kantecki@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

e100 parts don't support vlan offload but they generally do
allow use of vlans in higher software layers via the 8021q module.
That said, there are a couple of really old revisions of e100
hardware that don't even allow the longer frame sizes
required for vlan use with standard MTU.

Use the VLAN_CHALLENGED flag to prevent vlan binding to these
devices.
Reported-by: NMichael Tokarev <mjt@tls.msk.ru>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: David Lamparter <equinox@diac24.net>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This debugging message was recently added but it does not need to be as
alarming as a WARN.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 9e903e08 ("net: add skb frag size accessors") used frag_size
instead of skb_frag_size in this file.

Fixes this build error:

drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit':
drivers/net/ethernet/xilinx/ll_temac_main.c:717:3: error: implicit declaration of function 'frag_size' [-Werror=implicit-function-declaration]
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macintosh CS89x0 based ethernet cards use a Crystal Semiconductor (Now
Cirrus Logic) CS89x0 chip, so the mac89x0 driver should be in
drivers/net/ethernet/cirrus instead of drivers/net/ethernet/apple.

This also fixes a build problem, as the driver needs a header file from the
cirrus directory:

drivers/net/ethernet/apple/mac89x0.c:107:20: error: cs89x0.h: No such file or directory
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While the SC92031 could be found on fake "Realtek" NICs, it has no
relationship to Realtek, and is actually from Silan.

Create a new subdirectory for silan and move sc92031 there.
Signed-off-by: NCesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The `#define filename' screws up the expansion of
DEFINE_DYNAMIC_DEBUG_METADATA:

drivers/net/ethernet/i825xx/3c505.c: In function 'send_pcb':
drivers/net/ethernet/i825xx/3c505.c:390: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:390: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c:436: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:435: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c: In function 'start_receive':
drivers/net/ethernet/i825xx/3c505.c:557: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:557: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c: In function 'receive_packet':
drivers/net/ethernet/i825xx/3c505.c:629: error: expected identifier before string constant

etc

So remove that #define and "open-code" it.

Cc: Philip Blundell <philb@gnu.org>
Cc: David Miller <davem@davemloft.net>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>