Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 30 10月, 2007 9 次提交
  3. 23 10月, 2007 3 次提交
  5. 20 10月, 2007 6 次提交
  7. 19 10月, 2007 3 次提交
  9. 18 10月, 2007 3 次提交
    • R
      [MIPS] Probe for usability of cp0 compare interrupt. · b0d4056d
      由 Ralf Baechle 提交于 
      Some processors offer the option of using the interrupt on which
normally the count / compare interrupt would be signaled as a normal
interupt pin.  Previously this required some ugly hackery for each
system which is much easier done by a quick and simple probe.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      b0d4056d
    • M
      [MIPS] SYNC emulation for MIPS I processors · 60b0d655
      由 Maciej W. Rozycki 提交于 
      Userland, including the C library and the dynamic linker, is keen to use
the SYNC instruction, even for "generic" MIPS I binaries these days.
Which makes it less than useful on MIPS I processors.

This change adds the emulation, but as our do_ri() infrastructure was not
really prepared to take yet another instruction, I have rewritten it and
its callees slightly as follows.

Now there is only a single place a possible signal is thrown from.  The
place is at the end of do_ri().  The instruction word is fetched in
do_ri() and passed down to handlers.  The handlers are called in sequence
and return a result that lets the caller decide upon further processing.
If the result is positive, then the handler has picked the instruction,
but a signal should be thrown and the result is the signal number.  If the
result is zero, then the handler has successfully simulated the
instruction.  If the result is negative, then the handler did not handle
the instruction; to make it more obvious the calls do not follow the usual
0/-Exxx result convention they now return -1 instead of -EFAULT.

The calculation of the return EPC is now at the beginning.  The reason is
it is easier to handle it there as emulation callees may modify a register
and an instruction may be located in delay slot of a branch whose result
depends on the register.  It has to be undone if a signal is to be raised,
but it is not a problem as this is the slow-path case, and both actions
are done in single places now rather than the former being scattered
through emulation handlers.

The part of do_cpu() being covered follows the changes to do_ri().
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

---
      60b0d655
    • R
      [MIPS] Fix modpost warning in raw binary builds. · 396a2ae0
      由 Ralf Baechle 提交于 
        MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x478): Section mismatch: reference to .init.text:start_kernel (between '_stext' and 'run_init_process')
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      396a2ae0
  11. 17 10月, 2007 10 次提交
  13. 15 10月, 2007 1 次提交
    • S
      kbuild: enable 'make CFLAGS=...' to add additional options to CC · a0f97e06
      由 Sam Ravnborg 提交于 
      The variable CFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.

This patch replace use of CFLAGS with KBUILD_CFLAGS all over the
tree and enabling one to use:
make CFLAGS=...
to specify additional gcc commandline options.

One usecase is when trying to find gcc bugs but other
use cases has been requested too.

Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k

Test was simple to do a defconfig build, apply the patch and check
that nothing got rebuild.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
      a0f97e06
  15. 13 10月, 2007 1 次提交
  17. 12 10月, 2007 4 次提交