Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before we send probes in connection monitoring we check if scan is not
pending. But we do that check without locking. Fix that and also do not
start scan if connection monitoring is in progress.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were sending the LTO TLV as a version TLV instead of the actual link
timeout one.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dsap and ssap were swapped when sending DN or DISC.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The if logic could lead to zero length TLVs.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

recv_n is set properly when receiving an HDLC frame.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

At KERN_DEBUG level.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some HW/drivers get notifications when a tag moves out of the radio field.
This notification is now forwarded to user space through netlink.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The target index can be used by userspace to uniquely identify a target
and thus should be kept unique, per NFC adapter. Moreover, some protocols
do not provide a logical index when discovering new targets, so we have to
generate one for them.
For NCI or pn533 to fetch their logical index, we added a logical_idx field
to the target structure.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Most NFC HCI chipsets actually use a simplified HDLC link layer to
carry HCI payloads.
This implementation registers itself as an HCI device on behalf of the
NFC driver.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is an implementation of ETSI TS 102 622 specification.
Many NFC chipsets use HCI as the host <-> target protocol on top of a
serial link like i2c.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

NFC drivers will call this routine when they detect that a tag leaves the
RF field. This will eventually lead to the corresponding netlink event
to be sent.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some chips are capable of detecting when a tag is out of the field, so
they could send a netlink event about it to userspace.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Record the RANN sender's address only for RANNs that meet the acceptance
criteria (per sections 13.10.12.4.2).
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Reviewed-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware may decide to switch channels while already beaconing, e.g.
in response to a cfg80211 connect request on a different vif. Add this
event to notify userspace when an AP or GO interface has successfully
migrated to a new channel, so it can update its configuration
accordingly.
Signed-off-by: NThomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In WoWLAN, we only get the triggers when we actually get
to suspend. As a consequence, drivers currently don't
know that the device should enable wakeup. However, the
device_set_wakeup_enable() API is intended to be called
when the wakeup is enabled, not later when needed.

Add a new set_wakeup() call to cfg80211 and mac80211 to
allow drivers to properly call device_set_wakeup_enable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Eliad's comment prompted me to look closer at
the error paths in ieee80211_do_open() and I
found one that should use the error labels.

Also add a comment about the clear_bit since
in many error cases the bit hasn't been set.

Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.

To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.

Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The queue mapping redesign that I'm planning to do
will break pure injection unless we handle monitor
interfaces explicitly. One possible option would
be to have the driver tell mac80211 about monitor
mode queues etc., but that would duplicate the API
since we already need to have queue assignments
handled per virtual interface.

So in order to solve this, have a virtual monitor
interface that is added whenever all active vifs
are monitors. We could also use the state of one
of the monitor interfaces, but managing that would
be complicated, so allocate separate state.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The AP netdev is really only active when beaconing, so
manage the carrier state accordingly. Also do that for
VLAN interfaces enslaved to a given AP interface.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Section 13.2.3 of IEEE 80211s standard requires BSSBasicRateSet of mesh nodes
to be identical to establish peer link.
Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Basic rates are added with supported rates IE and extended supported
rates IE.
Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Report Toffset to userspace.
Let userspace select the mesh synchronization method.
Signed-off-by: NMarco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: NPavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds MBSS extensible synchronization framework (Sec.
13.13.2 of IEEE Std. 802.11-2012).

The framework is implemented via an ops table which defines the
following functions:

    rx_bcn_presp() - this is called every time a mesh beacon is
received.
    adjust_tbtt() - this is called immediately before a beacon is about
to be transmitted.

The default neighbor offset synchronization defined in the standard is
implemented.  We also provide template functions for vendor specific
methods.

When neighbor offset synchronization is active (which is the default)
mesh neighbors in the same MBSS will track timing offsets to each other
and compensate clock drift.

In our tests we observed that this mesh synchronization implementation
successfully corrected drifts between stations of ~2PPM while
introducing a jitter of ~20us.

It is also possible to test this framework on mac80211_hwsim simulated
phys to see how it behaves under different topologies, over poor links,
etc.
Signed-off-by: NMarco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: NPavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reading and writing back the tsf value via tsf is too slow if one wants
to make small increments to this timer.  With this change you can use
the syntax "+=<some value>" or "-=<some value>" to add or substract a
value from the tsf counter.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While associated we should never have empty SSID, but life can be full
of surprises, and is allways better to print a warning than crash.

Before memcpy() in ieee80211_probereq_get() check ssid_len instead of
ssid pointer, sice pointer it always passed by "ssidie + 2" expression
to send probe functions, so practically never can be NULL.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When adding pending SKBs there's no need to
stop all queues, we only need to stop those
that we're adding frames to. Implement that
by lazily stopping a queue as we add an SKB.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the queue status changes we need to do a fair
bit of work, so ignore no-op changes early.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we get more hardware queues, we'll still want
to only have netdev queues per AC, so set it up in
that way. If the hardware doesn't support QoS (by
not supporting at least 4 queues) the netdevs get
a single queue only (this is no change in behavior
as there are no drivers with 2 or 3 queues today.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers that don't support QoS also don't support
setting up their ACs, catch that early. While at
it, remove the input check since cfg80211 does it
now.

Also fix up the restart code to not try to set up
the queues in this case.

Finally also change the tx_conf array to have
IEEE80211_NUM_ACS entries instead of # of queues
since that's what it really needs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the plan to change mac80211's queue API to
not map ACs to queues 1:1, it seems necessary to
clarify some APIs that act on ACs rather than on
queues to spell that out explicitly. Do this.

Also verify that the AC number given is valid.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Devices that have internal rate control need to be
notified when the bandwidth or SMPS state changes
just like external rate control algorithms get a
notification now.

Add this notification and clarify the change bits
while at it, the HT_CHANGED bit really meant only
bandwidth changed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We currently stop the queue when changing the rate
control between 20/40 MHz in the BSS. This seems to
have been necessary when we actually changed the
channel, but now that we just update the station it
doesn't seem right any more. Remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>