When hns_nic_poll_rx_skb alloc skb fail, it will break receive cycle and
read new fbd_num to start new receive cycle. It recomputes cycle num is
fbd_num minus clean_count, actually this cycle num is too big because
it drop out receive cycle. It brings about the port unavailable.

So we will goto out when alloc skb fail to fix this bug.
Signed-off-by: NJun He <hjat2005@huawei.com>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default driver sets anchor led bit to 0 when link down,
actually, the anchor bit should be set to 1, so fixes it when
link status is down.
Secondly, change the return value of cpld_set_led_id to 0, which
means leave the cpld to control led blink frequece other than the
driver itself.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When network interface is enabled, the ring enable operation is
conducted twice. This patch deletes the redundancy code of ring enable,
and integrates hnae_ae_ops.toggle_queue_status other functions to
hns_ae_start.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds get_coalesce_range api for hns, it shows
range of coalesce usecs and frames that can be set on
this interface.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current driver stores the high bit value of tcam data register
to the tcam data low element, stores the low bit value of tcam data
register to tcam data high element, this patch fixes this bug.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds spin lock for tcam table operation,
there maybe a race condition happens when more than
one thread try to change the tcam talbe entries.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For SoC hip06, PFC pause handled in dsaf, while hip05 in XGMAC,
so change the statistics of pfc pause in dsaf and remove the old
pfc pause frame statistics.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For debug-ports,there are two non-synchronized processes:
Speed-Auto-Negotiation and Link-Update-Status. The two
processes are towed by two different state machines.
Bond reads the speed when link up, but the speed maybe
not update the right value at that time.That make for bond's
wrong speed. Thus only one state machine should be used and
if phy_state_machine is used, it does not need to do
hns_nic_update_link_status().
Signed-off-by: NQianqian Xie <xieqianqian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When run ethtool cmd(ethtool -t ethx) again and again for a long
time, it will be probabilistically fail. The PHYs' registers may
be on different pages, so it must be switch to the right page
before setting PHYs' registers.
And __lb_up() calls phy_start() to startup the PHYs device, but
this function may change Copper Control Register(Page 0, Register 0)
to an other value. It would cause phy loopback test fail. if we
remove phy_start(), we have to remove the relative phy_stop(),
phy_disconnect() when doing phy loopback to keep the phy stay in
right status.
Reported-by: Nhejun <hjat2005@huawei.com>
Signed-off-by: NKejian Yan <yankejian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As Hilink3 and Hilink4 use the same xge training and xge u adaptor for
HNSv2, it needs to select which Hilink to be set before relative serdes
being configed. The hilink_access_sel is the register to do that.
Signed-off-by: NKejian Yan <yankejian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error info should be printed as "set mask to 64bit fail!" instead of
"set mask to 32bit fail!" in dma_set_mask_and_coherent().
Signed-off-by: NQianqian Xie <xieqianqian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver uses devm_ioremap_resource, it will unmap the map
automatically, remove the unnecessary the resource free.
Signed-off-by: NQianqian Xie <xieqianqian@huawei.com>
Reported-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The annotation info for hns_nic_reset_subtask() should be
"for resetting subtask" instead of "for resetting suntask".
Signed-off-by: NQianqian Xie <xieqianqian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HNS receives a packet without doing anything, but it should call
skb_reset_mac_header() to initialize the header before using
eth_hdr().

Fixes: 0d6b425aSigned-off-by: NKejian Yan <yankejian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For service port, hns dsaf v1 support to close tx_pause.
However, the port will be invalid when it run command
ethtool to close tx_pause. This patch will fix it.
Signed-off-by: NQianqian Xie <xieqiaqian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bit fileds of PPE reset register are different between HNS v1 and
HNS v2, but the current procedure just only match HNS v1. Here is a
patch to fix it.
Signed-off-by: NKejian Yan <yankejian@huawei.com>
Signed-off-by: NQianqian Xie <xieqianqian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: probe compatible

This patchset factorizes the legacy and new SMI probing and abstracts
the switch register accesses. This simplifies adding support for new
chips or alternative register accesses.

This will allow us to use a compatible chip info to describe how to
access the SMI device and its switch ID register at probe time.

For the legacy probe, we fix the compatible info to 88E6085. For the
MDIO probe, we will use the compatible info from the device node data.

All patches are reviewed.

Changes since v4:

  - fix debug printing (was 'val' instead of '*val')

Changes since v3 [3]:

  - better register access abstraction using the chip structure

Changes since v2 [2]:

  - do not guess compatible model in legacy probe
  - add low level SMI API using a chip structure
  - allocate before probe and detection
  - add 3 cosmetic patches

Changes since v1 [1]:

  - merge style fix from Ben Dooks
  - add Acked-by/Reviewed-by tags
  - drop one compatible string per model
  - detect the SMI device based on the compatible info
  - add an SMI ops structure

[1] https://lkml.org/lkml/2016/6/8/1201
[2] https://lkml.org/lkml/2016/6/14/671
[3] https://lkml.org/lkml/2016/6/17/995
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the SMI address of the switch chip is zero, the chip assumes to be
the only one on the SMI master bus and thus responds to all its known
SMI devices addresses (port registers, Global2, etc.)

When its SMI address is not zero, some chips (e.g. 88E6352) use an
indirect access through two SMI Command and Data registers.

Other models (e.g. 88E6060) using less than 16 internal SMI addresses
always use a direct access.

Add a capability flag to describe chips supporting the (indirect)
Multi-chip Addressing Mode, and a low-level API to access the registers
via SMI.

Other accesses (like Ethernet management frames) may be added later.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switch ID is located at address 0x3 of every Port Registers bank.

But not all Marvell switches have their Port Registers SMI Addresses
starting at 0x10. 88E6060 starts at 0x8 and 88E6390 starts at 0x0.

Add this data in the info structure and use it in the detection code.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After allocating the chip structure, pass it a compatible info pointer.

The compatible info structure will be used later to describe how to
access the switch registers and where to read the switch ID.

For the standard MDIO probe, get it from the device node data. For the
legacy DSA driver probing, pass it the 88E6085 info.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract the common detection code which assigns the info structure to
the chip given the read switch ID.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an helper function to isolate SMI specific assignments and checks.

This function will later help choosing the different SMI accesses based
of the compatible info.

Since the chip structure is already allocated in the legacy probe, use
the mv88e6xxx_reg_read access routine instead of __mv88e6xxx_reg_read.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an helper function to allocate the chip structure at the beginning
of the probe functions. It will be used to initialize the SMI access.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip smi_mutex mutex is used to protect the access to the internal
switch registers, not only the Multi-chip Addressing Mode, as commented.

Since we will isolate SMI-specific pieces of code, avoid the confusion
now by renaming smi_mutex to reg_lock. No functional changes here.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6xxx_table array and the mv88e6xxx_lookup_info function are
static, so remove the table and size arguments from the lookup function.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the optional variant to get the reset GPIO line, instead of checking
for the -ENOENT error.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mixed assignments, allocations and registrations in the probe code
make it hard to follow the logic and figure out what is DSA or chip
specific.

Extract the struct dsa_switch related code in a simple
mv88e6xxx_register_switch helper function.

For symmetry in the code, add a mv88e6xxx_unregister_switch function.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MDIO device probe and remove functions are respectively incrementing
and decrementing the bus refcount themselves. Since these bus level
actions are out of the device scope, remove them.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the MDIO probing function, dev is already assigned to &mdiodev->dev
and np is already assigned to mdiodev->dev.of_node, so use them.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip->ds and ds->slave_mii_bus assignments are common to both legacy
and new MDIO probing and are already done in the later setup code.

Remove the duplicated assignments from the MDIO probing code.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes 5 style problems reported by checkpatch:

    WARNING: suspect code indent for conditional statements (8, 24)
    #492: FILE: drivers/net/dsa/mv88e6xxx.c:492:
    +	if (phydev->link)
    +			reg |= PORT_PCS_CTRL_LINK_UP;

    CHECK: Logical continuations should be on the previous line
    #1318: FILE: drivers/net/dsa/mv88e6xxx.c:1318:
    +		     oldstate == PORT_CONTROL_STATE_FORWARDING)
    +		    && (state == PORT_CONTROL_STATE_DISABLED ||

    CHECK: multiple assignments should be avoided
    #1662: FILE: drivers/net/dsa/mv88e6xxx.c:1662:
    +		vlan->vid_begin = vlan->vid_end = next.vid;

    WARNING: line over 80 characters
    #2097: FILE: drivers/net/dsa/mv88e6xxx.c:2097:
    +				       const struct switchdev_obj_port_vlan *vlan,

    WARNING: suspect code indent for conditional statements (16, 32)
    #2734: FILE: drivers/net/dsa/mv88e6xxx.c:2734:
    +		if (mv88e6xxx_6352_family(ps) || mv88e6xxx_6351_family(ps) ||
    [...]
    +				reg |= PORT_CONTROL_EGRESS_ADD_TAG;

    total: 0 errors, 3 warnings, 2 checks, 3805 lines checked

It also rebases and integrates changes sent by Ben Dooks [1]:

    The driver has a number of functions that are not exported or
    declared elsewhere, so make them static to avoid the following
    warnings from sparse:

    drivers/net/dsa/mv88e6xxx.c:113:5: warning: symbol 'mv88e6xxx_reg_read' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:167:5: warning: symbol 'mv88e6xxx_reg_write' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:231:5: warning: symbol 'mv88e6xxx_set_addr' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:367:6: warning: symbol 'mv88e6xxx_ppu_state_init' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:3157:5: warning: symbol 'mv88e6xxx_phy_page_read' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:3169:5: warning: symbol 'mv88e6xxx_phy_page_write' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:3583:26: warning: symbol 'mv88e6xxx_switch_driver' was not declared. Should it be static?
    drivers/net/dsa/mv88e6xxx.c:3621:5: warning: symbol 'mv88e6xxx_probe' was not declared. Should it be static?

[1] http://patchwork.ozlabs.org/patch/632708/Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Acked-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Acked-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
ipv6: better traceroute support in sit and gre

In commit ca15a078 ("sit: generate icmpv6 error when receiving icmpv4
error"), Oussama Ghorbel added minimal support for SIT tunnels to
generate ICMPv6 messages when receiving ICMPv4 messages.

This patch series extends this to GRE tunnels.

It also adds support for ICMPV6_TIME_EXCEED.

Partial support for RFC 4884 is added, to forward ICMP Multi-part
extensions eventually found in the ICMPv4 message.

v2: replaced an overlapping memcpy() by memmove()
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When receiving an ICMPv4 message containing extensions as
defined in RFC 4884, and translating it to ICMPv6 at SIT
or GRE tunnel, we need some extra manipulation in order
to properly forward the extensions.

This patch only takes care of Time Exceeded messages as they
are the ones that typically carry information from various
routers in a fabric during a traceroute session.

It also avoids complex skb logic if the data_len is not
a multiple of 8.

RFC states :

   The "original datagram" field MUST contain at least 128 octets.
   If the original datagram did not contain 128 octets, the
   "original datagram" field MUST be zero padded to 128 octets.

In practice routers use 128 bytes of original datagram, not more.

Initial translation was added in commit ca15a078
("sit: generate icmpv6 error when receiving icmpv4 error")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipgre_err() can call ip6_err_gen_icmpv6_unreach() for proper
support of ipv4+gre+icmp+ipv6+... frames, used for example
by traceroute/mtr.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For better traceroute/mtr support for SIT and GRE tunnels,
we translate IPV4 ICMP ICMP_TIME_EXCEEDED to ICMPV6_TIME_EXCEED

We also have to translate the IPv4 source IP address of ICMP
message to IPv6 v4mapped.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We want to use this helper from GRE as well, so this is
the time to move it in net/ipv6/icmp.c

Also add a @nhs parameter, since SIT and GRE have different
values for the header(s) to skip.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>