Registers new BPF program types which correspond to the LWT hooks:
  - BPF_PROG_TYPE_LWT_IN   => dst_input()
  - BPF_PROG_TYPE_LWT_OUT  => dst_output()
  - BPF_PROG_TYPE_LWT_XMIT => lwtunnel_xmit()

The separate program types are required to differentiate between the
capabilities each LWT hook allows:

 * Programs attached to dst_input() or dst_output() are restricted and
   may only read the data of an skb. This prevent modification and
   possible invalidation of already validated packet headers on receive
   and the construction of illegal headers while the IP headers are
   still being assembled.

 * Programs attached to lwtunnel_xmit() are allowed to modify packet
   content as well as prepending an L2 header via a newly introduced
   helper bpf_skb_change_head(). This is safe as lwtunnel_xmit() is
   invoked after the IP header has been assembled completely.

All BPF programs receive an skb with L3 headers attached and may return
one of the following error codes:

 BPF_OK - Continue routing as per nexthop
 BPF_DROP - Drop skb and return EPERM
 BPF_REDIRECT - Redirect skb to device as per redirect() helper.
                (Only valid in lwtunnel_xmit() context)

The return codes are binary compatible with their TC_ACT_
relatives to ease compatibility.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A route on the output path hitting a RTN_LOCAL route will keep the dst
associated on its way through the loopback device. On the receive path,
the dst_input() call will thus invoke the input handler of the route
created in the output path. Thus, lwt redirection for input must be done
for dsts allocated in the otuput path as well.

Also, if a route is cached in the input path, the allocated dst should
respect lwtunnel configuration on the nexthop as well.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

orig_output for IPv4 was only set for dsts which hit an input route.
Set it consistently for locally generated traffic as well to allow
lwt to continue the dst_output() path as configured by the nexthop.

Fixes: 25368623 ("lwt: Add support to redirect dst.input")
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 updates 2016-11-29

The following series from Tariq and Roi, provides some critical fixes
and updates for the mlx5e driver.

From Tariq:
 - Fix driver coherent memory huge allocation issues by fragmenting
   completion queues, in a way that is transparent to the netdev driver by
   providing a new buffer type "mlx5_frag_buf" with the same access API.
 - Create UMR MKey per RQ to have better scalability.

From Roi:
 - Some fixes for the encap-decap support and tc flower added lately to the
   mlx5e driver.

v1->v2:
 - Fix start index in error flow of mlx5_frag_buf_alloc_node, pointed out by Eric.

This series was generated against commit:
31ac1c19 ("geneve: fix ip_hdr_len reserved for geneve6 tunnel.")
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handling flow encap entry should be inside tc del flow
and is only relevant for offloaded eswitch TC rules.

Fixes: 11a457e9b6c1 ("net/mlx5e: Add basic TC tunnel set action for SRIOV offloads")
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the function that deletes offloaded TC rule to get
struct mlx5e_tc_flow instance which contains both the flow
handle and flow attributes. This is a cleanup needed for
downstream patches, it doesn't change any functionality.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the reverse unwinding principle, on delete time we should
first handle deletion of the steering rule and later handle the vlan
deletion from the eswitch.

Fixes: 8b32580d ("net/mlx5e: Add TC vlan action for SRIOV offloads")
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We will never find a flow with the same cookie as cls_flower always
allocates a new flow and the cookie is the allocated memory address.

Fixes: e3a2b7ed ("net/mlx5e: Support offload cls_flower with drop action")
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Striding RQ implementation, we used a single UMR
(User-Mode Memory Registration) memory key for all RQs.
When the product of RQs number*size gets high, we hit a
limitation of u16 field size in FW.

Here we move to using a UMR memory key per RQ, so we can
scale to any number of rings, with the maximum buffer
size in each.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In next patch we are going to create a UMR MKey per RQ, we need
mlx5e_create_umr_mkey declared before mlx5e_create_rq.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new type of struct mlx5_frag_buf which is used to allocate fragmented
buffers rather than contiguous, and make the Completion Queues (CQs) use
it as they are big (default of 2MB per CQ in Striding RQ).

This fixes the failures of type:
"mlx5e_open_locked: mlx5e_open_channels failed, -12"
due to dma_zalloc_coherent insufficient contiguous coherent memory to
satisfy the driver's request when the user tries to setup more or larger
rings.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reported-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Neill Whillans says:

====================
net: Add support for SGMII PCS on Altera TSE MAC

These patches were created as part of work to add support for SGMII
PCS functionality to the Altera TSE MAC. Patches are based on 4.9-rc6
git tree.

The first patch in the series adds support for the VSC8572 dual-port
Gigabit Ethernet transceiver, used in integration testing.

The second patch adds support for the SGMII PCS functionality to the
Altera TSE driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the (optional) SGMII PCS functionality of the Altera
TSE MAC. If the phy-mode is set to 'sgmii' then we attempt to discover
and initialise the PCS so that the MAC can communicate to the PHY.

The PCS IP block provides a scratch register for testing presence of
the PCS, which is mapped into one of the two MDIO spaces present in
the MAC's register space.  Once we have determined that the scratch
register is functioning, we attempt to initialise the PCS to
auto-negotiate an SGMII link with the PHY. There is no need to monitor
or manage the SGMII link beyond this, since the normal PHY MDIO will
then be used to monitor the media layer.

The Altera TSE MAC has only one way in which it can be configured with an
SGMII PCS, and as such, this patch only looks to the phy-mode to select
whether or not to attempt to initialise the PCS registers.  During
initialisation, we report the PCS's equivalent of a PHY ID register.
This can be parameterised during the IP instantiation and is often left
as '0x00000000' which is not an error.
Signed-off-by: NNeill Whillans <neill.whillans@codethink.co.uk>
Reviewed-by: NDaniel Silverstone <daniel.silverstone@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the Vitesse VSC8572 which is functionally equivalent to
the already supported VSC8574. As such, all the same handling functions
are used since the VSC8572 merely has half the number of phy blocks
internally.
Signed-off-by: NStephen Agate <stephen.agate@uk.thalesgroup.com>
Signed-off-by: NNeill Whillans <neill.whillans@codethink.co.uk>
Reviewed-by: NDaniel Silverstone <daniel.silverstone@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: defalconisation fixups

A bug fix, the Kconfig change, and cleaning up a bit more unused code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's no longer used now that Falcon is gone.

Also remove a reference in a comment to an ioctl that doesn't exist.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Easy enough for Falcon users to enable it when making oldconfig.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Defalconisation removed one of the string arguments, but missed the
 corresponding %s.

Fixes: 5a6681e2 ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this patch, function ndo_dflt_fdb_dump() will always return code
from uc fdb dump. The reture code of mc fdb dump is lost.
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netlink kernel socket is protected by refcount, not RCU.
Its rcv path is neither protected by RCU. So the synchronize_net()
is just pointless.

Cc: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Raju Lakkaraju says:

====================
Adding PHY MDI(X) support

I updated all review comments which were given by Andrew and Florian.

This series add support for PHY MDI(X), and implement it for MSCC phys.

Tested on Beaglebone Black with VSC 8531 PHY.

Change set:
v1:
- Initial patch submit the WoL and MDI-X in single set of patches

v2:
- Split the mdi(x) as signal set of patches.
- Remove the out_unlock as suggested by Andrew.
- Add mdix_ctrl parameter in "phy_device" to handle the user configure
  mdi(x). Proposed implementation accepted by Florian.
- phydev->mdix_ctrl initialize with ETH_TP_MDI_AUTO. Ethernet controller
  never initialize this parameter.
- Fix the mdix changes in marvell and microchip driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY drivers to have an eth_tp_mdix_ctrl to indicate what is the configured
MDI setting, and read eth_tp_mdi to indicate what is the current status,

Add new parameter mdix_ctrl in phy_device structure and fix driver.
Signed-off-by: NRaju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To connect two ports of the same configuration (MDI to MDI or
MDI-X to MDI-X) with a 10/100/1000 Mbit/s connection, an
Ethernet crossover cable is needed to cross over the transmit
and receive signals in the cable, so that they are matched at
the connector level.
When connecting an MDI port to an MDI-X port a straight through
cable is used while to connect two MDI ports or two MDI-X ports
a crossover cable must be used. Conventionally MDI is used on end
devices while MDI-X is used on hubs and switches

Auto MDI-X automatically detects the required cable connection
type and configures the connection appropriately, removing the
need for crossover cables to interconnect switches or connecting
PCs peer-to-peer.
Signed-off-by: NRaju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the mdix and mdix_ctrl with corresponding ethtool configuration
parameters.
Signed-off-by: NRaju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new parameter mdix_ctrl to hold the user configuration.
Existing mdix maintain the current status of MDI(X) crossover performed or
not.
mdix_ctrl can configure either ETH_TP_MDI or ETH_TP_MDI_X orETH_TP_MDI_AUTO.
Signed-off-by: NRaju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mtu_adj is initialized to zero when alloc mem, there is no any
assignment to mtu_adj. It is only used in ipvlan_adjust_mtu as one
right value.
So it is useless member of struct ipvl_dev, then remove it.
Signed-off-by: NGao Feng <fgao@ikuai8.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In alloc_cmd_box(), pci_pool_alloc() followed by memset will be
replaced by pci_pool_zalloc()
Signed-off-by: NSouptick joarder <jrdr.linux@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In mlx4_alloc_cmd_mailbox(), pci_pool_alloc() followed by memset will be
replaced by pci_pool_zalloc()
Signed-off-by: NSouptick joarder <jrdr.linux@gmail.com>
Reviewed-by: NYuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e2d118a1 ("net: inet: Support UID-based routing in IP
protocols.") made __build_flow_key call sock_net(sk) to determine
the network namespace of the passed-in socket. This crashes if sk
is NULL.

Fix this by getting the network namespace from the skb instead.

Fixes: e2d118a1 ("net: inet: Support UID-based routing in IP protocols.")
Reported-by: NErez Shitrit <erezsh@dev.mellanox.co.il>
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a test to verify that

bpf: fix states equal logic for varlen access

actually fixed the problem.  The problem was if the register we added to our map
register was UNKNOWN in both the false and true branches and the only thing that
changed was the range then we'd incorrectly assume that the true branch was
valid, which it really wasnt.  This tests this case and properly fails without
my fix in place and passes with it in place.
Signed-off-by: NJosef Bacik <jbacik@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ivan Khoronzhuk says:

====================
cpsw: add per channel shaper configuration

This series is intended to allow user to set rate for per channel
shapers at cpdma level. This patchset doesn't have impact on performance.
The rate can be set with:

echo 100 > /sys/class/net/ethX/queues/tx-0/tx_maxrate

Tested on am572xx
Based on net-next/master
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split device budget between channels according to channel rate.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check budget fullness only after it's updated and update
channel mask only once to keep budget balance between channels.
It's also needed for farther changes.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows to rate limit queues tx queues for cpsw interface.
The rate is set in absolute Mb/s units and cannot be more a speed
an interface is connected with.

The rate for a tx queue can be tested with:

ethtool -L eth0 rx 4 tx 4

echo 100 > /sys/class/net/eth0/queues/tx-0/tx_maxrate
echo 200 > /sys/class/net/eth0/queues/tx-1/tx_maxrate
echo 50 > /sys/class/net/eth0/queues/tx-2/tx_maxrate
echo 30 > /sys/class/net/eth0/queues/tx-3/tx_maxrate

tc qdisc add dev eth0 root handle 1: multiq

tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5001 0xffff action skbedit queue_mapping 0

tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5002 0xffff action skbedit queue_mapping 1

tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5003 0xffff action skbedit queue_mapping 2

tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5004 0xffff action skbedit queue_mapping 3

iperf -c 192.168.2.1 -b 110M -p 5001 -f m -t 60
iperf -c 192.168.2.1 -b 215M -p 5002 -f m -t 60
iperf -c 192.168.2.1 -b 55M -p 5003 -f m -t 60
iperf -c 192.168.2.1 -b 32M -p 5004 -f m -t 60
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpdma has 8 rate limited tx channels. This patch adds
ability for cpdma driver to use 8 tx h/w shapers. If at least one
channel is not rate limited then it must have higher number, this
is because the rate limited channels have to have higher priority
then not rate limited channels. The channel priority is set in low-hi
direction already, so that when a new channel is added with ethtool
and it doesn't have rate yet, it cannot affect on rate limited
channels. It can be useful for TSN streams and just in cases when
h/w rate limited channels are needed.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The weight of a channel is needed to split descriptors between
channels. The weight can depend on maximum rate of channels, maximum
rate of an interface or other reasons. The channel weight is in
percentage and is independent for rx and tx channels.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed*: Add XDP support

This patch series is intended to add XDP to the qede driver, although
it contains quite a bit of cleanups, refactorings and infrastructure
changes as well.

The content of this series can be roughly divided into:

 - Datapath improvements - mostly focused on having the datapath utilize
parameters which can be more tightly contained in cachelines.
Patches #1, #2, #8, #9 belong to this group.

 - Refactoring - done mostly in favour of XDP. Patches #3, #4, #5, #9.

 - Infrastructure changes - done in favour of XDP. Paches #6 and #7 belong
to this category [#7 being by far the biggest patch in the series].

 - Actual XDP support - last two patches [#10, #11].
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for forwarding via XDP. Once the eBPF is attached,
driver would allocate & configure a designated transmission queue
meant solely for forwarding packets. Said queue would share the
receive-queue's interrupt line, and would have it's own Tx statistics.

Infrastructure changes required for this [spread-out through the code]:
 - Determine the DMA direction of the receive buffers based on the presence
of the eBPF program.
 - Turn the sw Tx ring into a union, as regular/XDP queues have different
needs for releasing resources after completion [regular requires the SKB,
XDP requires the transmitted page].
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the ndo_xdp callback. This patch would support XDP_PASS,
XDP_DROP and XDP_ABORTED commands.

This also adds a per Rx queue statistic which counts number of packets
which didn't reach the stack [due to XDP].
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve the cacheline usage of both queues by reordering -
This reduces the cachelines required for egress datapath processing
from 3 to 2 and those required by ingress datapath processing by 2.

It also changes a couple of datapath related functions that currently
require either the fastpath or the qede_dev, changing them to be based
on the tx/rx queue instead.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>