Enable the audio drivers in the non-corenet 85xx defconfigs so that audio
is enabled on the Freescale P1022DS reference board.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

As a result of changes to Kconfig files, we no longer enable
the lockup and hung task detectors. Both are very light weight
and provide useful information in the event of a hang, so
reenable them.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Add mpt2sas driver to pseries and ppc64 defconfig.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The IRQs off tracer enables mcount which has a big impact on
performance. Disable it.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The pseries defconfig had a number of drivers enabled and we may
as well add them to the ppc64 defconfig.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The 44x code (which is shared by 47x) assumes the available physical memory
begins at 0x00000000.  This is not necessarily the case in an AMP
environment.

Support CONFIG_RELOCATABLE for 476 in order to allow the kernel to be
loaded into a higher memory range.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NDave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
 - Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
 - Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

CONFIG_PPC_EPAPR_HV_BYTECHAN adds support for the Freescale hypervisor
byte channel tty driver.

CONFIG_VIRT_DRIVERS and CONFIG_FSL_HV_MANAGER add support for the Freescale
hypervisor management driver.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Remove duplicate assignment of SCSI_BNX2_ISCSI in pseries_defconfig
introduced by:
  37e0c21e powerpc/pseries: Enable iSCSI support for a number of cards

causes warning:
arch/powerpc/configs/pseries_defconfig:151:warning: override: reassigning to symbol SCSI_BNX2_ISCSI
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

P1010RDB Overview
 -----------------
 1Gbyte DDR3 (on board DDR)
 32Mbyte 16bit NOR flash
 32Mbyte SLC NAND Flash
 256 Kbit M24256 I2C EEPROM
 128 Mbit SPI Flash memory
 I2C Board 128x8 bit memory
 SD/MMC connector to interface with the SD memory card
 2 SATA interface
         1 internal SATA connect to 2.5. 160G SATA2 HDD
         1 eSATA connector to rear panel
 USB 2.0
         x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
         x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
 eTSEC1: Connected to RGMII PHY VSC8641XKO
 eTSEC2: Connected to SGMII PHY VSC8221
 eTSEC3: Connected to SGMII PHY VSC8221 eCAN
 Two DB-9 female connectors for Field bus interface UART
 DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable framebuffer console support by default in the defconfig on the
Freescale MPC8610 HPCD reference board.  This allows the boot messages to
be shown on the video display.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable framebuffer console support by default in the defconfigs for the
Freescale 85xx-based reference board.  This allows the boot messages to
be shown on the video display on the P1022DS.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture.  This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The e500mc and e5500 based cores are only available on corenet based
SoCs.  We use this name for the P204x, P3040, P4040, P4080, P50x0 SoCs
and any future processors in these families.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Rather than trying to use the core name we use corenet to distinquish
the platform/core combo.  corenet64 will be a 64-bit kernel build and
we'll add a new defconfig for corenet32 for a 32-bit platforms.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

RTC_CLASS is changed to bool, so 'm' is invalid.
Signed-off-by: NWanlong Gao <wanlong.gao@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NHans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ns_cgroup is an annoying cgroup at the namespace / cgroup frontier and
leads to some problems:

  * cgroup creation is out-of-control
  * cgroup name can conflict when pids are looping
  * it is not possible to have a single process handling a lot of
    namespaces without falling in a exponential creation time
  * we may want to create a namespace without creating a cgroup

  The ns_cgroup was replaced by a compatibility flag 'clone_children',
  where a newly created cgroup will copy the parent cgroup values.
  The userspace has to manually create a cgroup and add a task to
  the 'tasks' file.

This patch removes the ns_cgroup as suggested in the following thread:

https://lists.linux-foundation.org/pipermail/containers/2009-June/018616.html

The 'cgroup_clone' function is removed because it is no longer used.

This is a userspace-visible change.  Commit 45531757 ("cgroup: notify
ns_cgroup deprecated") (merged into 2.6.27) caused the kernel to emit a
printk warning users that the feature is planned for removal.  Since that
time we have heard from XXX users who were affected by this.
Signed-off-by: NDaniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: NSerge E. Hallyn <serge.hallyn@canonical.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Reviewed-by: NLi Zefan <lizf@cn.fujitsu.com>
Acked-by: NPaul Menage <menage@google.com>
Acked-by: NMatt Helsley <matthltc@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This debug option has no overhead other than a slight increase in
kernel size, and makes bug reports more useful.  While some end users
may prefer to save the space, as a default on a kernel config aimed
primarily at development on reference boards, it should be enabled.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Even though support for the p5020's on-chip ethernet is not yet upstream,
it is not appropriate to disable all networking support (including
loopback, unix domain sockets, external ethernet devices, etc) in the
defconfig.  The networking settings are taken from mpc85xx_smp_defconfig,
minus the drivers for ethernet devices not found on any current e5500
chip.

The other changes are the result of running "make savedefconfig".
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable iSCSI support for a number of cards. We had the base
networking devices enabled but forgot to enable iSCSI.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Enable the Qlogic and Emulex 10Gbit adapters.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

BT_L2CAP and BT_SCO have changed to bool .
Value 'm' has invalid .
Signed-off-by: NWanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Ensure the Chelsio T3/T4 network drivers and iWARP drivers are
enabled in the pseries config.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Uwe Kleine-König reported:

	while working on an defconfig (arm/mx27) I noticed that just updating
	it[1] results in removing CONFIG_EEPROM_AT24=y.  The reason is that
	since commit

		v2.6.36-5965-g5f2365d8 (misc devices: do not enable by default)

	MISC_DEVICES isn't enabled anymore by default.  So all defconfigs that
	have CONFIG_SOME_SYMBOL=y (or =m) (with SOME_SYMBOL depending on
	MISC_DEVICES) but not CONFIG_MISC_DEVICES=y suffer from the same
	problem.

This restores those misc devices to the powerpc defconfigs.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Acked-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Uwe Kleine-König
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The MPC852 based mgsuvd board from Keymile was initially ported,
but later on not developed further. This patch removes the respective
files to decrease merging conflicts and unneeded maintenance.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher<hs@denx.de>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The mgcoge board from keymile is now base for some other
similar boards. Therefore the board specific name mgcoge
was renamed to a generic name km82xx. Additionally some
enhancements were made:
	- rework partition table in dts file
	- add cpm2_pio_c gpio controller in dts file
	- update defconfig
	- add pin description for SCC1
	- add pin description and configuration for USB
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Beside the MPC 8360 based board kmeter1 other km83xx boards
from keymile will follow. Therefore the board specific naming
kmeter1 for functions and files were replaced with km83xx.
Additionally some updates were made:
    - update defconfig for 2.6.38
    - rework flash partitioning in dts file
    - add gpio controller for qe_pio_c in dts
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Upcoming servers will include a Broadcom NIC, add to the defconfig to
increase testing coverage and make sure mainline builds come up with
networking.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

- Enable 64kB pages so it gets some regular testing.

- The largest POWER7 has 1024 threads so bump NR_CPUS it to match.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

IRQSOFF_TRACER and STACK_TRACER force the kernel to be built with -pg
which is a substantial overhead.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.

This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel.  A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).

Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NDavid Woodhouse <david.woodhouse@intel.com>
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Add Clock Power Management (CPM) node to dts tree
- Add idle-doze entry in CPM node
- Add standby entry in CPM node
- Add PM and SUSPEND support by default in defconfig
- Remove UART2 and UART3 as they are unused, this will
  allow CPM to put unused-units (UART2 and UART3) to sleep.
Signed-off-by: NVictor Gallardo <vgallardo@apm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

- Add Clock Power Management (CPM) node to dts tree
- Add idle-doze entry in CPM node
- Add standby entry in CPM node
- Add PM and SUSPEND support by default in defconfig
- Add NO_HZ and CONFIG_HIGH_RES_TIMERS support by
  default in defconfig
Signed-off-by: NVictor Gallardo <vgallardo@apm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The Freescale P1022DS has an on-chip video controller called the DIU, and a
driver for this device already exists.  Update the platform file for the
P1022DS reference board to enable the driver, and update the defconfig for
Freescale MPC85xx boards to add the driver.

[Edited to resolve header add/add conflict and drop #define DEBUG.
-- broonie]
Signed-off-by: NTimur Tabi <timur@freescale.com>
Acked-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Make sure the new bluestone board is selected for the multiplatform defconfig.
Also build logfs and squashfs as modules.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The p5020 SoC from Freescale is the first 64-bit Book-E processor and
utilizes the two e5500 cores.  Adding a defconfig that enables basic kernel
for e5500 based processors.

Also added the p5020 / e5500 support to the ppc64e defconfig.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds CPU, device tree, defconfig and bluestone board
support for APM821xx SoC.
Signed-off-by: NTirumala R Marri <tmarri@apm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This trims all our defconfigs using make savedefconfig
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Supported SMC1 (serial console), SCC1 Ethernet (10Mbps HD).
FEC Ethernet, 8MB NOR CFI Flash.

Tested on STK8xx with TQM860L (with FEC) and with TQM855M (without FEC).
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Introduce basic support for the Freescale P1022DS reference board, based on the
Freescale BSP for this board.  This patch excludes the DIU, SSI, and MMC/SD
drivers.  Only a 36-bit DTS is provided.

Update mpc86xx_smp_defconfig and mpc85xx_defconfig to support the P1022DS.
This means enabling 64-bit physical address support, increasing the maximum
zone order to 12 (to allow the DIU driver to allocate large chunks), and
clean up the audio options to disable the deprecated OSS support.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>