Part 1 of Thermal Throttling Management -

Thermal Throttling feature is used to put NIC into low power state when
driver detect the Radio temperature reach pre-defined threshold

Two Thermal Throttling Management Methods; this patch introduce the
Legacy Thermal Management:
   IWL_TI_0: normal temperature, system power state
   IWL_TI_1: high temperature detect, low power state
   IWL_TI_2: higher temperature detected, lower power state
   IWL_TI_CT_KILL: critical temperature detected, lowest power state

Once get into CT_KILL state, uCode go into sleep, driver will stop all
the active queues, then move to IWL_TI_CT_KILL state; also set up 5
seconds timer to toggle CSR flag, uCode wake up upon CSR flag change,
then measure the temperature.
If temperature is above CT_KILL exit threshold, uCode go backto sleep;
if temperature is below CT_KILL exit threshold, uCode send Card State
Notification response with appropriate CT_KILL status flag, and uCode
remain awake, Driver receive Card State Notification Response and update
the card temperature to the CT_KILL exit threshold.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If advance thermal throttling is used the driver need to pass both
"enter" and "exit" temperature to uCode.

Using different critical temperature threshold for legacy and advance
thermal throttling management based on the type of thermal throttling
method is used except 1000.
For 1000, it use advance thermal throttling critical temperature
threshold, but with legacy thermal management implementation until ucode
has the necessary implementations in place.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When performing rate scaling, if detected that the new rate
index is invalid, clear the search_better_tbl flag
so it will not be stuck in the loop.

Since the search table is already set up in uCode,
we need to empty out the the search table;
revert back to the "active" rate and throughput info.
Also pass the "active" table setup to uCode to make
sure the rate scale is functioning correctly.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a station queries us for a PS-poll response, we wrongly
queue the frame on the virtual interface's queue rather than
the pending queue.

Additionally, fix a race condition where we could potentially
send multiple frames to the sleeping station due to using a
station flag rather than a packet flag. When converting to a
packet flag, we can also convert p54 and remove the filter
clearing we added for it.

(Also remove a now dead function)
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Reported-by: NBob Copeland <me@bobcopeland.com>
Tested-by: NBob Copeland <me@bobcopeland.com>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleanup aggregation start/stop function interfaces.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These can be obtained from mac80211.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update filename for debug information.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TH gets 5 GHz.

Cc: David Quan <david.quan@atheros.com>
Cc: Michael Green <michael.green@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00dev->default_ant should be initialized once by the driver,
and should not be changed afterwards. Because rt2x00lib_config_antenna()
was using a reference to the struct antenna_setup it actually had the oppurtunity
to change the default antenna setting and it actually did that during the validation.

Instead of passing a pointer to antenna_setup the entire structure should be copied.
Signed-off-by: NLars Ericsson <Lars_Ericsson@telia.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[PATCH net-next-2.6] bnx2: Update vlan_features

In order to get full use of some advanced features of BNX2, we now need to
fill dev->vlan_features.

Patch successfully tested with vlan devices built on top of bonding.
(bond0 : one bnx2 slave, one tg3 slave (not yet vlan_features enabled)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. add intel's sdio vendor id to sdio_ids.h
2. move iwmc3200 sdio devices' ids to sdio_ids.h
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patrick said : "vlan_features doesn't need to be updated, the resulting
dev->features of the VLAN device is computed as the intersection of
dev->features and dev->vlan_features."
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change resolves some warnings seen with DMA debugging enabled in which
we were mapping skb->data with size + NET_IP_ALIGN and unmapping it with
just size.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The igb driver is currently initializing the mailbox function pointers
after the phy.  This causes issues as the phy init will return from the
function early if there is no phy present.

To resolve this I have moved the function pointer init to a location prior
to the phy initialization so that serdes based adapters can also make use
of SR-IOV.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans up the flow control configuration for igb to make it a
bit more readable in regards to what the requested and current modes are.
This should help with the maintainability of the current igb driver in
regards to flow control.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that we use buffer_info->dma instead of
shinfo->nr_frags to determine if we need to unmap a received skb.  By doing
this we can avoid a cache miss on small packets since the buffer_info
structure should already be prefetched.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for a new 82576 mezzanine adapter.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a switch statement in igb_set_wol that defaults to break and
doesn't actually do anything.  As such it should be removed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This update cleans up the receive address register initialization.  The
main purpose of this is to clean out some redundancy that was introduced
due to having multiple ways of setting the receive address registers.
Instead of having a specialized function to set one register and one to set
all of them it makes more sense to just go through the list calling the
function that is needed to set the individual registers.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves all of the multicast addresses out of the free Receive
address registers and instead programs them all into the multicast table
array.  As a result the multicast filtering may not be as precise, but it
also greatly reduces the overhead for multicast addresses.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 82575 and 82576 hardware can both experience data corruption issues if
a pci-e completion arrives after the timeout value.  In order to avoid this
we need to increase the timeout value while pci-e master is disabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The igb driver was overwritting the LED settings that were configured via
EEPROM.  This is not correct behavior as the LED settings are meant to be
configured by EEPROM and not changed.  This change removes the code that
was setting the LED behavior on the interface.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since igb_configure_pcs_link always returns 0 there isn't really much point
to checking for the result so it is best just to change this to a void so
we can properly ignore the return result.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was a serdes power down workaround that was originally added for
82576 fiber.  However it has also been found that this workaround is needed
for serdes connections as well.  In addition it is also needed for 82575
serdes so we we need to remove the checks restricting it to 82576.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current igb driver only supports copper and serdes.  The fiber media
type is a holdover from earlier NICs as the current nics supported by igb
all use serdes when communicating over a fiber connection.  As a result we
can remove media type fiber without losing any functionality.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the PCI probe function struct pci_device_id points to the matched
entry of the ID table, but for devices which are matched with
PCI_ANY_ID sub IDs we want display the IDs of the device itself.
Signed-off-by: NKarsten Keil <keil@b1-systems.de>

These changes were a direct result of using a semantic patch
More information can be found at http://www.emn.fr/x-info/coccinelle/

Modified some of the changes to avoid the extra define.
Signed-off-by: NStoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>

The result of container_of should not be NULL.  In particular, in this case
the argument to the enclosing function has passed though INIT_WORK, which
dereferences it, implying that its container cannot be NULL.

A simplified version of the semantic patch that makes this change is as
follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
identifier fn,work,x,fld;
type T;
expression E1,E2;
statement S;
@@

static fn(struct work_struct *work) {
  ... when != work = E1
  x = container_of(work,T,fld)
  ... when != x = E2
- if (x == NULL) S
  ...
}
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>

Add support for cards based on the Tiger 300 and Tiger 320
ISDN PCI chip.
Currently only the ISAC ISDN line interface is supported.
Signed-off-by: NKarsten Keil <keil@b1-systems.de>

Add driver for Winbond W6692 based PCI cards.
Signed-off-by: NKarsten Keil <keil@b1-systems.de>

Add support for the Siemens ISAR DSP chip and cards based on it,
including analog modem protocols.
Signed-off-by: NKarsten Keil <keil@b1-systems.de>

Add mISDN driver for AVM FRITZ!CARD PCI (all versions).
Signed-off-by: NKarsten Keil <keil@b1-systems.de>

This driver supports cards with Infineon ISAC/HSCX, ISACX, IPAC
and IPACX chips from various manufacturers.
Signed-off-by: NKarsten Keil <keil@b1-systems.de>

Clearing B-channel is needed in every driver, so it makes sense
to have it as common function.
Signed-off-by: NKarsten Keil <keil@b1-systems.de>