It's possible that the controller has an individually switchable power supply.
Therefore add support to control a supplying regulator.

As this is not always the case, the regulator is requested as optional.
Signed-off-by: NHeiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds a driver for Microchips CAP1106, an I2C driven, 6-channel
capacitive touch sensor.

For now, only the capacitive buttons are supported, and no specific
settings that can be tweaked for individual channels, except for the
device-wide sensitivity gain. The defaults seem to work just fine out of
the box, so I'll leave configurable parameters for someone who's in need
of them and who can actually measure the impact. All registers are
prepared, however. Many of them are just not used for now.

The implementation does not make any attempt to be compatible to platform
data driven boards, but fully depends on CONFIG_OF.

Power management functions are also left for volounteers with the ability
to actually test them.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This adds DT support to the tsc2005 touchscreen driver. It also adds
regulator support to the driver if booted via DT.
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add common DT binding documentation for touchscreen devices and
implement input_parse_touchscreen_of_params, which parses the common
properties and configures the input device accordingly.

The method currently does not interpret the axis inversion properties,
since there is no matching flag in the generic linux input device.
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This is an input driver and belongs to input not gpio.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The sun4i resisitive touchscreen controller also comes with a built-in
temperature sensor. This commit adds support for it.

This commit also introduces a new "ts-attached" device-tree property,
when this is not set, the input part of the driver won't register. This way
the internal temperature sensor can be used to measure the SoC temperature
independent of there actually being a touchscreen attached to the controller.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Note the sun4i-ts controller is capable of detecting a second touch, but
when a second touch is present then the accuracy becomes so bad the
reported touch location is not useable.

The original android driver contains some complicated heuristics using the
aprox. distance between the 2 touches to see if the user is making a pinch
open / close movement, and then reports emulated multi-touch events around
the last touch coordinate (as the dual-touch coordinates are worthless).

These kinds of heuristics are just asking for trouble (and don't belong in
the kernel). So this driver offers straight forward, reliable single touch
functionality only.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds ST Keyscan driver to use the keypad hw a subset of ST
boards provide. Specific board setup will be put in the given dt.
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: NGiuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds a new driver for keypad for Cirrus Logic CLPS711X CPUs.
Target CPU contain keyboard interface which can scan 8 column lines,
so we can read row GPIOs to read status and determine asserted state.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This makes the zforce driver usable on devicetree-based platforms too.
Signed-off-by: NHeiko Stuebner <heiko.stuebner@bqreaders.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add device tree support for twl4030 keypad driver.

Tested on Nokia N900.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Update all the Tegra DT bindings to require resets/reset-names properties
where the HW module has reset inputs. Remove any entries from clocks or
clock-names that were only required to identify reset inputs, rather than
referring to real clocks.

This is a DT-ABI-incompatible change. It is the first of two changes
required for me to consider the Tegra DT bindings as stable, the other
being conversion to the common DMA DT bindings.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-By: NTerje Bergstrom <tbergstrom@nvidia.com>

Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.

All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-By: NTerje Bergstrom <tbergstrom@nvidia.com>

This patch adds a new driver for the beeper controlled via GPIO pin.
The driver does not depend on the architecture and is positioned as
a replacement for the specific drivers that are used for this function.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add device tree support for twl4030 power button driver.

Adding device tree support involved converting the
driver to module_platform_driver().
Signed-off-by: NSebastian Reichel <sre@debian.org>
Acked-by: NKumar Gala <galak@codeaurora.org>
Tested-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NDenis Carikli <denis@eukrea.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

There was a spelling mistake on TSC/ADC binding where "coordinate" was
spelled as "coordiante".

We can't simply fix the error due to DT being an ABI, the approach taken
was to first use correct spelling and if that fails, fall back to
miss-spelled version.

It's unfortunate that has creeped into the tree.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Adding a simple device tree binding for the specification of key
sequences. Definition of the keys found in the sequence are located in
'include/uapi/linux/input.h'.

For the sysrq driver, holding the sequence of keys down for a specific
amount of time will reset the system.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: NGrant Likely <grant.likely@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

With device core now able to setup the default pin configuration,
the pin configuration code based on the deprecated Samsung specific
gpio bindings is removed.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NChao Xie <chao.xie@marvell.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds DT support to touch driver. It also provides a binding
document which is used by the MFD and IIO part of the device.
This patch also renames steps_to_configure to coordinate_readouts
because the original name misleads the purpose of the variable.
Signed-off-by: NPantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: NPatil, Rachna <rachna@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>

This is a driver for the keypads found on the TI-Nspire series calculators.
Signed-off-by: NDaniel Tang <dt.tangr@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

We add the possibility to hand over a GPIO number for the reset pin.
This way we can remove existing board code that takes care of it and
group this information properly in the platform data or in the device
tree configuration.
Signed-off-by: NBastian Hecht <hechtb+renesas@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Use the key-matrix layer to interpret key scan information from the EC
and inject input based on the FDT-supplied key map. This driver registers
itself with the ChromeOS EC driver to perform communications.

The matrix-keypad FDT binding is used with a small addition to control
ghosting.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NLuigi Semenzato <semenzato@chromium.org>
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

APBPS2 is a PS/2 core part of GRLIB found in SPARC32/LEON
products.
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add the necessary code to create the needed platformdata from devicetree
informations.

The interrupt mode of the chip is not set via devicetree, as it is not
a property of the hardware but instead only a preferred type of operation.
This should probably be made settable via configfs in the future.
The option set as default is the mode the datasheet mentions as default.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Some matrix keypad drivers can support different numbers of rows and
columns. Add a generic binding for these.

Implementation note:

In order to implement this binding in the kernel, we will need to modify
matrix_keypad_() to look up the number of rows and cols in
the keymap. Perhaps this could be done by passing 0 for these parameters?
Many of the parameters can already be set to NULL. Ick.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The NVIDIA's Tegra KBC has maximum 24 pins to make matrix keypad.
Any pin can be configured as row or column. The maximum column pin
can be 8 and maximum row pin can be 16.

Remove the assumption that all first 16 pins will be used as row
and remaining as columns and Add the property for configuring pins
to either row or column from DT. Update the devicetree binding
document accordingly.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds device tree support for imx keypad driver.
Signed-off-by: NLiu Ying <Ying.Liu@freescale.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NAlban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch allows the STMPE driver to be successfully probed and
initialised when Device Tree support is enabled. Besides the usual
platform data changes, we also separate the process of filling in
the 'in use' pin bitmap, as we have to extract the information from
Device Tree in the DT boot case.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch allows the STMPE Touchscreen driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.
Signed-off-by: NVipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Also the driver was modifued to take advantage of recent improvements in
matrix_keypad_build_keymap() implementation, which automatically allocates
memory for keymap.

The driver was tested on AM335x EVM.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

A very simple binding, the only property is the phandle to the PWM.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>