Mode set sequence outlines when the AUX VDD bit should be set and
cleared, and it's separate from the panel power sequence.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Mode set sequence requires that we start training, then enable the
panel, then complete training.  So split the DP training function into
two parts; the first enables the DP port and sets training pattern 1 and
the second completes the training.

As part of this, remove some redundant function args from the various DP
handling functions and use the intel_dp fields everywhere we can.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[ickle: removed first ironlake_edp_backlight_on() on advice of jbarnes]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Mode setting sequence specifies that we use VDD AUX for configuration
and detection, and early in the mode set sequence.  Only later (after
DP_A has started training) should we actually enable panel power.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[ickle: checkpatch.pl complaining about whitespace]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Fix the test so we don't try to use the 450MHz refclk on PCH attached
eDP.

References:
  https://bugs.freedesktop.org/show_bug.cgi?id=29141Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Panel needs to be powered up.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

snprintf() returns the number of bytes which would have been used if
there was enough space.  It can be larger than the size of the buffer.
Obviously in this case the buffer is large enough but everyone just
copy and pastes this code so it's better to limit it and set a good
example.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Use the detection from intel-gtt.ko instead. Hooray!

Also move the stolen mem allocator to the other gtt stuff in dev_prv->mem.

v2: Chris Wilson noted that my error handling was crap. Fix it. He also
said that this fixes a problem on his i845. Indeed, i915_probe_agp
misses a special case for i830/i845 stolen mem detection.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=25476
Cc: stable@kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Not used and simply confusing.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This way create_gatt_table become dummy glue functions for the fake
agp driver - rename them accordingly (and kill the now unnecessary
i9xx copy).

With this change, the gtt initialization code is almost independant
from the agp stuff. Two things are still missing:
- the scratch page is created by the generic agp code.
- filling the whole gtt with scratch_page ptes is not yet consolidated -
  this needs abstracted pte handling, first.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The only difference between i915 and i965 was the calculation of the
gtt address. So merge these two paths into one. Otherwise the same
changes as in the i830 setup consolidation.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Slighlty reordered sequence was necessary. Also don't set
agp_bridge->gatt_bus_addr anymore. Only used by generic agp helper
functions, hence unnecessary for the intel fake agp driver.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This way around this can be extracted into common code.

Also use a common cleanup function (and give it a generic name).
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Also move the Sandybdridge size detection into gtt_total_entries, like
the rest.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Slight reordering of the init sequence required.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Same idea as INTEL_INFO from drm/i915. This
- reduces the dependancy on agp_driver
- stops the what-does-IS_I965G-mean confusion (here it's just gen4, in
  drm/i915 it's gen >=4)
- further prepares the separation of the fake agp driver from the rest.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

In commit f1befe71 Chris Wilson added some code to clear the full gtt
on g33/pineview instead of just the mappable part. The code looks like
it was copy-pasted from agp/intel-gtt.c, at least an identical piece
of code is still there (in intel_i830_init_gtt_entries). This lead to
a regression in 2.6.35 which was supposedly fixed in commit e7b96f28

Now this commit makes absolutely no sense to me. It seems to be
slightly confused about chipset generations - it references docs for
4th gen but the regression concerns 3rd gen g33. Luckily the the g33
gmch docs are available with the GMCH Graphics Control pci config
register definitions. The other (bigger problem) is that the new
check in there uses the i830 stolen mem bits (.5M, 1M or 8M of stolen
mem). They are different since the i855GM.

The most likely case is that it hits the 512M fallback, which was
probably the right thing for the boxes this was tested on.

So the original approach by Chris Wilson seems to be wrong and the
current code is definitely wrong. There is a third approach by Jesse
Barnes from his RFC patch "Who wants a bigger GTT mapping range?"
where he simply shoves g33 in the same clause like later chipset
generations.

I've asked him and Jesse confirmed that this should work. So implement
it.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16891$Tested-by: NAnisse Astier <anisse@astier.eu>
Cc: stable@kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Start to separate the fake agp driver from the rest of intel-gtt.c
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

agp/intel_gtt.c and drm/i915/i915_dma.c don't calculate this the same
way: The intel-gtt code seems to use the actual gtt size, the drm
module just the mappable. Go with the logic from the drm module because
that's the more conservative choice.

But conserve the original code in intel_gtt_total_size for later use.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The dedection function in drm/i915/i915_dma.c works without it, so
drop it here, too. All the values are disdinct, anyway.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This somewhat aligns it with the version in drm/i915/i915_dma.c.
Changes:
- s/gtt_entries/stolen_size
- track overhead entries in a seperate var (the effective gtt size
  calculation will be extracted later on).
- subtract the overhead at the end instead of in each clause.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This uses the new mappable gtt size detection from the previous patch.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This implementation is stolen from drm/i915, but is equivalent to
the code sprinkled over intel-gtt.c in the various fetch_size functions.
It's not yet used anywhere, though.

Also introduce intel_gtt_init which only calls intel_gtt_stolen_entries.
Over the course of the next patches, this will grow untill it contains
the complete init sequence starting from the call to gtt_mappable_entries.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

First simple step towards a more generic initialization. This
is needed to disentangle the agp stuff from the stuff that is
actually needed by drm/i915.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

When the intel-gtt code now longer depends on agp, we cannot rely
on this. So store a local reference in intel-gtt.c.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Add a few definitions to it that are already shared and that will
be shared in the future (like the number of stolen entries).
No functional changes in here.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Now that the disentangling is complete, stop including intel-gtt.c
from intel-agp.c.

The linux build system _really_ doesn't allow .c source files with the
same name as the module. It fails with the following message when trying
to build such a bugger:

make[3]: Circular drivers/char/agp/intel-agp.o <- drivers/char/agp/intel-agp.o dependency dropped.

Instead of renameing intel-agp.c I've simply created a new module out
of intel-gtt.c. Renaming intel-agp.ko to something else is not an option
for it will surely kill someones boot process.

This also paves the way to use the gtt code without loading the agp
driver.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This just splits the device list into two and moves the gtt related stuff
to intel-gtt.c. The two new devices lists also lose the not longer needed
fields. There where only about 5 cases anyway with both a gmch and a
possible agp port, so the duplication of entries is rather small.
Additionally kill 2 out of the three Ironlake mobile entries that
only differed in host bridge pci id.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

It seems to be possible to program a new mode without disabling the panel
if the panel fitter setup doesn't change. Add support for that.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

We really need a macro to test whether a given connector has a panel
attached rather than sprinkling HAS_PCH_SPLIT/IS_eDP/has_edp_encoder
etc all over. In the meantime, fix the bug...
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[ickle: tidy up the duplicity in the conditionals]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Make them match the others and add BPP definitions.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Our usage of kmap() cannot return NULL here, so remove the unnecessary
error handling.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The GPU records whether it is currently waiting for a completion of a
WAIT_FOR_EVENT in the RB_WAIT bit in the ringbuffer control registers.
On third generation chipsets and later, a write of 1 to this bit breaks
the hang and returns the GPU to arbitration, i.e. the GPU should
continue executing the reminder of the batchbuffer and return to normal
operations.

By adding this to hangcheck we can avoid a full GPU reset under these
conditions.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

If we disable the pipe and the GPU is currently waiting on a scanline
WAIT_FOR_EVENT, the GPU will hang. Fortunately, there is a magic bit
which we can write on i915+ to break this wait after disabling the
pipe.

References:

  Bug 29252 - [Arrandale] Hung WAIT_FOR_EVENT when running rss-glx-skyrocket
  https://bugs.freedesktop.org/show_bug.cgi?id=29252

  Bug 28964 - [i965gm] GPU infinite MI_WAIT_FOR_EVENT while watching video in Totem
  https://bugs.freedesktop.org/show_bug.cgi?id=28964

and many others.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Hopefully this is a contributing factor to the spurious TV detection
repoted by Ivan Bulatovic and others.

References:

  Bug 16871 - "TV1 connected" with no tv
  https://bugzilla.kernel.org/show_bug.cgi?id=16871Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reported-by: NIvan Bulatovic <combuster@gmx.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>

There were two instances of code to control the panel backlight and
neither handled the complete set of device variations.

Fixes:

  Bug 29716 - [GM965] Regression: Backlight resets to minimum when changing resolution
  https://bugs.freedesktop.org/show_bug.cgi?id=29716

And a bug on one of my PineView boxes which overflowed the backlight
value.

Incorporates part of a similar patch by Matthew Garrett that exposes a
native Intel backlight controller.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

We do it whilst configuring dev->mode_config, so remove the out-of-place
earlier initialisation.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>