Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 27 10月, 2013 4 次提交
    • R
      libata: Add some missing command descriptions · 3915c3b5
      由 Robert Hancock 提交于 
      Add some missing command enumerations from the ATA-8 ACS-3 spec into
include/linux/ata.h, and add the corresponding human-readable command
descriptions in libata-eh.c.
Signed-off-by: NRobert Hancock <hancockrwd@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
      3915c3b5
    • D
      sata_highbank: clear whole array in highbank_initialize_phys() · 225f1eae
      由 Dan Carpenter 提交于 
      The original code used the wrong parameter to clear tx_atten[].  It
passed the number of elements instead of sizeof() the array to memset.

The other potential issue was that cphy_base[] wasn't cleared.  I'm not
sure if that was a real problem or not, but I have cleared it in my
patch.

Instead of using memset(), this patch uses empty initializers as a
cleanup.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
      225f1eae
    • X
      ahci: disabled FBS prior to issuing software reset · 89dafa20
      由 xiangliang yu 提交于 
      Tested with Marvell 88se9125, attached with one port mulitplier(5 ports)
and one disk, we will get following boot log messages if using current
code:

  ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier 1.2, 0x1b4b:0x9715 r160, 5 ports, feat 0x1/0x1f
  ahci 0000:03:00.0: FBS is enabled
  ata8.00: hard resetting link
  ata8.00: SATA link down (SStatus 0 SControl 330)
  ata8.01: hard resetting link
  ata8.01: SATA link down (SStatus 0 SControl 330)
  ata8.02: hard resetting link
  ata8.02: SATA link down (SStatus 0 SControl 330)
  ata8.03: hard resetting link
  ata8.03: SATA link up 6.0 Gbps (SStatus 133 SControl 133)
  ata8.04: hard resetting link
  ata8.04: failed to resume link (SControl 133)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.04: failed to read SCR 1 (Emask=0x40)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.03: native sectors (2) is smaller than sectors (976773168)
  ata8.03: ATA-8: ST3500413AS, JC4B, max UDMA/133
  ata8.03: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
  ata8.03: configured for UDMA/133
  ata8.04: failed to IDENTIFY (I/O error, err_mask=0x100)
  ata8.15: hard resetting link
  ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: hard resetting link
  ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: limiting SATA link speed to 3.0 Gbps
  ata8.15: hard resetting link
  ata8.15: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: failed to recover PMP after 5 tries, giving up
  ata8.15: Port Multiplier detaching
  ata8.03: disabled
  ata8.00: disabled
  ata8: EH complete

The reason is that current detection code doesn't follow AHCI spec:

First,the port multiplier detection process look like this:

	ahci_hardreset(link, class, deadline)
	if (class == ATA_DEV_PMP) {
		sata_pmp_attach(dev)	/* will enable FBS */
		sata_pmp_init_links(ap, nr_ports);
		ata_for_each_link(link, ap, EDGE) {
			sata_std_hardreset(link, class, deadline);
			if (link_is_online)	/* do soft reset */
				ahci_softreset(link, class, deadline);
		}
	}
But, according to chapter 9.3.9 in AHCI spec: Prior to issuing software
reset, software shall clear PxCMD.ST to '0' and then clear PxFBS.EN to
'0'.

The patch test ok with kernel 3.11.1.

tj: Patch white space contaminated, applied manually with trivial
    updates.
Signed-off-by: NXiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
      89dafa20
    • G
      libata: Fix display of sata speed · 3e85c3ec
      由 Gwendal Grignou 提交于 
      6.0 Gbps link speed was not decoded properly:
speed was reported at 3.0 Gbps only.

Tested: On a machine where libata reports 6.0 Gbps in
        /var/log/messages:
    ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

    Before:
    	cat /sys/class/ata_link/link1/sata_spd
    	3.0 Gbps
    After:
    	cat /sys/class/ata_link/link1/sata_spd
    	6.0 Gbps
Signed-off-by: NGwendal Grignou <gwendal@google.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
      3e85c3ec
  3. 15 10月, 2013 1 次提交
    • R
      ahci: imx: setup power saving methods · 8b789d89
      由 Richard Zhu 提交于 
      In order to save power consumption as much as possible.

* Disable sata phy internal pll reference clock when sysetem enter
  into suspend mode, enable it after resume.

* Setup module parameter used to enable imx ahci test power down
  mode(PDDQ) or not, when there is no device detected on the port

* minor modifications:
  - The format of the copyright is changed, because that the original
    one can't pass fsl internal patch reivew without the character
    '(c)'.
  - Exports ahci_platform_ops and ahci_error_handler().

NOTE:
* The hot-plug can't be supported when PDDQ mode is ever enabled.

* module parameter usage how-to:
  - default: enable PDDQ mode when no device detected.
  - add "ahci-imx.hotplug=1" into kernel command line if your don't
    want to enable PDDQ mode when no device detected on the port.

tj: Slightly updated description and comments.
Signed-off-by: NRichard Zhu <r65037@freescale.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
      8b789d89
  5. 14 10月, 2013 1 次提交
  7. 23 9月, 2013 1 次提交
  9. 13 9月, 2013 3 次提交
    • M
      Remove GENERIC_HARDIRQ config option · 0244ad00
      由 Martin Schwidefsky 提交于 
      After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      0244ad00
    • M
      MIPS: DECstation I/O ASIC DMA interrupt handling fix · 5359b938
      由 Maciej W. Rozycki 提交于 
      This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.

Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle).  Otherwise the handler is
reentered over and over again.

The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared.  Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'.  Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      5359b938
    • K
      thp: account anon transparent huge pages into NR_ANON_PAGES · 3cd14fcd
      由 Kirill A. Shutemov 提交于 
      We use NR_ANON_PAGES as base for reporting AnonPages to user.  There's
not much sense in not accounting transparent huge pages there, but add
them on printing to user.

Let's account transparent huge pages in NR_ANON_PAGES in the first place.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: NDave Hansen <dave.hansen@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Hugh Dickins <hughd@google.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Ning Qu <quning@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      3cd14fcd
  11. 12 9月, 2013 30 次提交