If some problem occurs during ehci startup, for instance, request_irq fails,
echi hcd driver tries it best to cleanup, but fails to unregister reboot
notifier, which in turn leads to crash on reboot/poweroff.

The following patch resolves this problem by not using reboot notifiers
anymore, but instead making ehci/ohci driver get its own shutdown method.  For
PCI, it is done through pci glue, for everything else through platform driver
glue.

One downside: sa1111 does not use platform driver stuff, and does not have its
own shutdown hook, so no 'shutdown' is called for it now.  I'm not sure if it
is really necessary on that platform, though.
Signed-off-by: NAleks Gorelov <dared1st@yahoo.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move <linux/usb_otg.h> to <linux/usb/otg.h>.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

inlined is the patch that adds basic support for USB OHCI controller
support for PNX4008 Philips PNX4008 ARM board. Due to HW design, it
depends on I2C driver for PNX4008 which I've recetnly posted to LKML and
i2c at lm-sensors.
Signed-off-by: NVitaly Wool <vitalywool@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This teaches OHCI to use the root hub status change (RHSC) IRQ, bypassing
root hub timers most of the time and switching over to the "new" root hub
polling scheme.  It's complicated by the fact that implementations of OHCI
trigger and ack that IRQ differently (the spec is vague there).

Avoiding root hub timers helps mechanisms like "dynamic tick" leave the
CPU in lowpower modes for longer intervals.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

OHCI updates for AT91 series processors:

 - Get ready for at91sam926x processors (ARMv5tej not ARMv4t)

 - Suspend/resume support now behaves properly

 - In "standby" mode, OHCI can be a source of system wakeup events
   (remote wakeup, device connect/disconnect, etc)

And minor cleanups.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds OHCI glue bits for the USB host interface in the
Cirrus ep93xx (arm920t) CPU.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

A loop on a power-lost resume path used the wrong index.
I suspect khubd has been working around such bugs.
Noticed by Andreas Mohr <andi@rhlx01.fht-esslingen.de>.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This makes OHCI use the driver model wakeup control bits for its root hub
(e.g. disable on amd756, because of chip erratum) and for the controller
itself.  It no longer uses the hcd glue bits with those roles, and depends
on the previous patch making the root hub available earlier.

Note that on most platforms (boot code properly setting the RWC bit) this
gives a partial workaround for the way PCI isn't currently flagging devices
that support PME# signals.  (Because of odd PCI init sequencing on PPC.)
That's because many OHCI controllers support "legacy PCI PM" ... without
involving any PCI PM capability.

USB wakeup from STR, if it works on your system, may still involve
tweaking things by hand in /proc/acpi/wakeup.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds support for OHCI on AT91rm9200 based boards.

Possibly of interest here is the way this uses <linux/clk.h> to
gate clocks on/off during system pm state transitions.  That's
typical for non-PCI systems.  Some can go further; Mini-A host
side connectors enable ID-pin sensing.

From: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as515b) adds a routine to usbcore to simplify handling of
host controllers that lost power or were reset during suspend/resume.
The new core routine marks all the child devices of the root hub as
NOTATTACHED and tells khubd to disconnect the device structures as soon
as possible.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This modifies the HCD builds to automatically "-DDEBUG" if
CONFIG_USB_DEBUG is selected.  It's just a minor source code cleanup,
guaranteeing consistency.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch closes the IRQ race and makes various other OHCI & EHCI code
path safer vs. suspend/resume.
I've been able to (finally !) successfully suspend and resume various
Mac models, with or without USB mouse plugged, or plugging while asleep,
or unplugging while asleep etc... all without a crash.

Alan, please verify the UHCI bit I did, I only verified that it builds.
It's very simple so I wouldn't expect any issue there. If you aren't
confident, then just drop the hunks that change uhci-hcd.c

I also made the patch a little bit more "safer" by making sure the store
to the interrupt register that disables interrupts is not posted before
I set the flag and drop the spinlock.

Without this patch, you cannot reliably sleep/wakeup any recent Mac, and
I suspect PCs have some more sneaky issues too (they don't frankly crash
with machine checks because x86 tend to silently swallow PCI errors but
that won't last afaik, at least PCI Express will blow up in those
situations, but the USB code may still misbehave).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This simplifies the OHCI root hub suspend logic:

 - Uses new usbcore root hub calls to make autosuspend work again:
	* Uses a newish usbcore root hub wakeup mechanism,
	  making requests to khubd not keventd.
	* Uses an even newer sibling suspend hook.

 - Expect someone always made usbcore call ohci_hub_suspend() before bus
   glue fires; and that ohci_hub_resume() is only called after that bus
   glue ran.  Previously, only CONFIG_USB_SUSPEND promised those things.
   (Includes updates to PCI and OMAP bus glue.)

 - Handle a not-noticed-before special case during resume from one of
   the swsusp snapshots when using "usb-handoff":  the controller isn't
   left in RESET state.  (A bug to fix in the usb-handoff code...)

Also cleans up a minor debug printk glitch, and switches an mdelay over
to an msleep (how did that stick around for so long?).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/ohci-dbg.c  |    4 ----
 drivers/usb/host/ohci-hcd.c  |    2 +-
 drivers/usb/host/ohci-hub.c  |   42 ++++++++++++------------------------------
 drivers/usb/host/ohci-mem.c  |    1 -
 drivers/usb/host/ohci-omap.c |   36 ++++++++++++------------------------
 drivers/usb/host/ohci-pci.c  |   40 ++++++++--------------------------------
 drivers/usb/host/ohci.h      |    1 -
 7 files changed, 33 insertions(+), 93 deletions(-)

This simplifies some of the PM-related #ifdeffing by recognizing
that USB_SUSPEND depends on PM.  Also, OHCI drivers were often
testing for USB_SUSPEND when they should have tested just PM.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hcd.c          |    2 ++
 drivers/usb/host/ohci-hcd.c     |    2 +-
 drivers/usb/host/ohci-hub.c     |    4 ++--
 drivers/usb/host/ohci-omap.c    |    2 +-
 drivers/usb/host/ohci-pci.c     |    2 +-
 drivers/usb/host/ohci-ppc-soc.c |    4 ++--
 drivers/usb/host/ohci-pxa27x.c  |    2 +-
 drivers/usb/host/ohci-s3c2410.c |    3 +--
 drivers/usb/host/ohci-sa1111.c  |    2 +-
 9 files changed, 12 insertions(+), 11 deletions(-)

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some OHCI implementations have differences in the way the NDP register
(in roothub_a) reports the number of ports present. This patch allows the
platform specific code to optionally supply the number of ports. The
driver just reads the value at init (if not supplied) instead of reading
it every time its needed (except for an AMD756 bug workaround).

It also sets the value correctly for the ARM pxa27x architecture.
Signed-Off-By: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Evidently there are some boards which care a lot about this, but
as a rule it's been hard to notice.

OHCI_INTR_RD wasn't always cleared in the ohci irq handler.  On some
systems this means certain remote wakeup scenarios could seem to hang
(in an interrupt storm, RD never clearing).

From: "William Morrow" <William.Morrow@amd.com>
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Description: Use schedule_timeout_{,un}interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB (OHCI) Host driver for S3C2410/S3C2440 based systems
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A patch re-organizing some parts of root hub initialization deleted the
code initializing the bus-neutral reboot/shutdown notifier for OHCI.
This patch just restores that deleted code.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Greg,

This patch fixes the kmalloc() flags argument type in USB
subsystem; hopefully all of its occurences. The patch was
made against patch-2.6.12-git2 from Jun 20.

Cleanup of flags for kmalloc() in USB subsystem.
Signed-off-by: NOlav Kongas <ok@artecdesign.ee>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch changes the host controller drivers; they no longer need to
register their root hubs because usbcore will take care of it for them.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch changes the HCDs that used the old hub_set_power_budget call,
making them use the new hcd->power_budget field instead.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds a reboot notifier to OHCI, mostly to benefit kexec; plus
minor #include tweaks.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!