Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Can be used to match packets against netfilter ip sets created via ipset(8).
skb->sk_iif is used as 'incoming interface', skb->dev is 'outgoing interface'.

Since ipset is usually called from netfilter, the ematch
initializes a fake xt_action_param, pulls the ip header into the
linear area and also sets skb->data to the IP header (otherwise
matching Layer 4 set types doesn't work).
Tested-by: NMr Dash Four <mr.dash.four@googlemail.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This introduce TSQ (TCP Small Queues)

TSQ goal is to reduce number of TCP packets in xmit queues (qdisc &
device queues), to reduce RTT and cwnd bias, part of the bufferbloat
problem.

sk->sk_wmem_alloc not allowed to grow above a given limit,
allowing no more than ~128KB [1] per tcp socket in qdisc/dev layers at a
given time.

TSO packets are sized/capped to half the limit, so that we have two
TSO packets in flight, allowing better bandwidth use.

As a side effect, setting the limit to 40000 automatically reduces the
standard gso max limit (65536) to 40000/2 : It can help to reduce
latencies of high prio packets, having smaller TSO packets.

This means we divert sock_wfree() to a tcp_wfree() handler, to
queue/send following frames when skb_orphan() [2] is called for the
already queued skbs.

Results on my dev machines (tg3/ixgbe nics) are really impressive,
using standard pfifo_fast, and with or without TSO/GSO.

Without reduction of nominal bandwidth, we have reduction of buffering
per bulk sender :
< 1ms on Gbit (instead of 50ms with TSO)
< 8ms on 100Mbit (instead of 132 ms)

I no longer have 4 MBytes backlogged in qdisc by a single netperf
session, and both side socket autotuning no longer use 4 Mbytes.

As skb destructor cannot restart xmit itself ( as qdisc lock might be
taken at this point ), we delegate the work to a tasklet. We use one
tasklest per cpu for performance reasons.

If tasklet finds a socket owned by the user, it sets TSQ_OWNED flag.
This flag is tested in a new protocol method called from release_sock(),
to eventually send new segments.

[1] New /proc/sys/net/ipv4/tcp_limit_output_bytes tunable
[2] skb_orphan() is usually called at TX completion time,
  but some drivers call it in their start_xmit() handler.
  These drivers should at least use BQL, or else a single TCP
  session can still fill the whole NIC TX ring, since TSQ will
  have no effect.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Tom Herbert <therbert@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Tested-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes build when ipv6 is disabled.
Reported-by: NFengguang Wu <wfg@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nobody provides non-zero values any longer.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No longer used.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A lot of code has either the memset or an inefficient copy
from a static array that contains the all-ones broadcast
address. Introduce eth_broadcast_addr() to fill an address
with all ones, making the code clearer and allowing us to
get rid of some constant arrays.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some devices (e.g. Sony's PaSoRi) can not do type B polling, so we have
to make a distinction between ISO14443 type A and B poll modes.

Cc: Eric Lapuyade <eric.lapuyade@intel.com>
Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This function is needed by brcmsmac. This code is based on code from
the Broadcom SDK.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This code is based on the Broadcom SDK and brcmsmac.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chip IDs are used all over bcma and no constants where defined.
This patch adds the constants and makes bcma use them.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is based on a recent version of the Broadcom SDK.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If registering of one of them fails, all already registered drivers
of this module will be unregistered.

Use the new register/unregister functions in all drivers
registering more than one driver.

amd.c, realtek.c: Simplify: directly return registration result.

Tested with broadcom.c
All others compile-tested.
Signed-off-by: NChristian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device managed flow steering API has three promiscuous modes:

1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.

Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is modified to support three operation modes.

If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.

When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.

When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.

Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.

This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.

A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.

B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,

The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now, a u16 value was used to represent bitrate value.
With VHT bitrates this becomes too small.

Introduce a new 32-bit bitrate attribute. nl80211 will report
both the new and the old attribute, unless the bitrate doesn't
fit into the old u16 attribute in which case only the new one
will be reported.

User space tools encouraged to prefer the 32-bit attribute, if
available (since it won't be available on older kernels.)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[reword commit message and comments a bit]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Most multi-queue networking driver consider the number of online cpus when
configuring RSS queues.
This patch adds a wrapper to the number of cpus, setting an upper limit on the
number of cpus a driver should consider (by default) when allocating resources
for his queues.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow setting of only supported flag bits in queue->flags.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

This ematch makes it possible to classify CAN frames (AF_CAN) according
to their identifiers. This functionality can not be easily achieved with
existing classifiers, such as u32, because CAN identifier is always stored
in native endianness, whereas u32 expects Network byte order.
Signed-off-by: NRostislav Lisovy <lisovy@gmail.com>
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Provide various constants as defined by the 802.11ad:
frame types, IE's, capability bits, action categories

Introduce GCMP cipher, mandatory by 802.11ad
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add enumerations for both cfg80211 and nl80211.
This expands wiphy.bands etc. arrays.

Extend channel <-> frequency translation to cover 60g band
and modify the rate check logic since there are no legacy
mandatory rates (only MCS is used.)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).

An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.

In the end, this patch also adds the EEE ethtool support implementing:
 o phy_ethtool_set_eee
 o phy_ethtool_get_eee

v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
    values according to ethtool API (thanks to Ben's feedback).
    Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
    Fixed the phy_init_eee function: we need to check which link mode
    was autonegotiated and then the corresponding bits in 7.60 and 7.61
    registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
    when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
    and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix kernel-doc warning.  This struct member was removed in commit
87568264 ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.

  Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Introduce IFF_LIVE_ADDR_CHANGE priv_flag and use it to disable
netif_running() check in eth_mac_addr()
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a hook in the binding path of netlink.

This is used by ctnetlink to allow module autoloading for the case
in which one user executes:

 conntrack -E

So far, this resulted in nfnetlink loaded, but not
nf_conntrack_netlink.

I have received in the past many complains on this behaviour.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the following structure:

struct netlink_kernel_cfg {
        unsigned int    groups;
        void            (*input)(struct sk_buff *skb);
        struct mutex    *cb_mutex;
};

That can be passed to netlink_kernel_create to set optional configurations
for netlink kernel sockets.

I've populated this structure by looking for NULL and zero parameters at the
existing code. The remaining parameters that always need to be set are still
left in the original interface.

That includes optional parameters for the netlink socket creation. This allows
easy extensibility of this interface in the future.

This patch also adapts all callers to use this new interface.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow drivers to advertise their VHT capabilities
and export them to userspace via nl80211.
Signed-off-by: NMahesh Palivela <maheshp@posedge.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add the VHT definitions to be used by drivers supporting it.
Signed-off-by: NMahesh Palivela <maheshp@posedge.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow PHY drivers to supply their own device matching function
(match_phy_device()), or to be matched OF compatible properties.

PHYs following IEEE802.3 clause 45 have more than one device
identifier constants, which breaks the default device matching code.
Other 10G PHYs don't follow the standard manufacturer/device
identifier register layout standards, but they do use the standard
MDIO bus protocols for register access.  Both of these require
adjustments to the PHY driver to device matching code.

If the there is an of_node associated with such a PHY, we can match it
to its driver using the "compatible" properties, just as we do with
certain platform devices.  If the "compatible" property match fails,
first check if there is a driver supplied matching function, and if
not fall back to the existing identifier matching rules.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IEEE802.3 clause 45 MDIO bus protocol allows for directly
addressing PHY registers using a 21 bit address, and is used by many
10G Ethernet PHYS.  Already existing is the ability of MDIO bus
drivers to use clause 45, with the MII_ADDR_C45 flag.  Here we add
struct phy_c45_device_ids to hold the device identifier registers
present in clause 45. struct phy_device gets a couple of new fields:
c45_ids to hold the identifiers and is_c45 to signal that it is clause
45.

get_phy_device() gets a new parameter is_c45 to indicate that the PHY
device should use the clause 45 protocol, and its callers are adjusted
to pass false.  The follow-on patch to of_mdio.c will pass true where
appropriate.

EXPORT phy_device_create() so that the follow-on patch to of_mdio.c
can use it to create phy devices for PHYs, that have non-standard
device identifier registers, based on the device tree bindings.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. removed code replication for tov calculation for 1G, 10G and
made is common for speed > 1G (1G, 10G, 40G, 100G).
2. defines values for #4 different 40G Phys (KR4, LF4, SR4, CR4)
Signed-off-by: NParav Pandit <parav.pandit@emulex.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removes all RTA_GET*() and RTA_PUT*() variations, as well as the
the unused rtattr_strcmp(). Get rid of rtm_get_table() by moving
it to its only user decnet.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of them are BCM4706 specific AFAWK. Most of them was confirmed on
Netgear WNDR450.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds the following messages to ctnetlink:

IPCTNL_MSG_CT_GET_STATS_CPU
IPCTNL_MSG_CT_GET_STATS
IPCTNL_MSG_EXP_GET_STATS_CPU

To display connection tracking system per-cpu and global statistics.

This provides a replacement for the following /proc interfaces:

/proc/net/stat/nf_conntrack
/proc/sys/net/netfilter/nf_conntrack_count
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

No longer used and a poor interface as they were macros
with embedded gotos.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>