The DMA context run control bit is entirely controlled by software, so
it is safe to cache it.  This allows the driver to avoid doing an
additional MMIO read when queueing an AT packet.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Add comments
  - on why bus_reset_tasklet flushes AT queues,
  - that commit 76f73ca1 can possibly be reverted now.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NJarod Wilson <jarod@redhat.com>

The OHCI 1.2 (draft) specification, clause 7.2.3.3, allows and
recommends that, after a bus reset, the controller does not flush all
the packets in the AT queues.  Therefore, the driver has to do this
itself.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

At ifup, carrier status would be shown on even if it actually was off.
Also add an include for ethtool_ops rather than to rely on the one from
netdevice.h.

Note, we can alas not use fwnet_device_mutex to serialize access to
dev->peer_count (as I originally wanted).  This would cause a lock
inversion:
  - fwnet_probe | takes fwnet_device_mutex
      + register_netdev | takes rtnl_mutex
  - devinet_ioctl | takes rtnl_mutex
      + fwnet_open | ...must not take fwnet_device_mutex

Hence use the dev->lock spinlock for serialization.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

To make userland, e.g. NetworkManager work with firewire, we need to
detect whether cable is plugged or not.  Simple and correct way of doing
that is just counting number of peers.  No peers - no link and vice
versa.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Unfortunately its easy to trigger such error messages by removing the
cable while sending streams of data over the link.

Such errors are normal, and therefore this patch stops firewire-net from
flooding the kernel log with these errors, by combining series of same
errors together.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>

(Stefan R:)  Eventually we should remove this logging when firewire-net
and related firewire-ohci facilities have been stabilized.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Restore iso channels DMA so that iso channels could continue to work
after resume from RAM/disk.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Some lousy BIOSes, e.g. my Aspire 5720 BIOS forget to restore the GUID
register on resume from RAM.

Fix that by setting it to the last value that was read from it.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The buffers used for the selfIDs packets and the AR request and response
descriptors end up using three pages because dma_alloc_coherent()
allocates at least one page per call.  However, these data structures
would all fit into 4 KB, so we can save space by using a common buffer
for them.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

When the isochRx/isochTx bit is clear, we do not need to read the
corresponding iso interrupt event register.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Change the header of PHY packets to be sent to include a pseudo
transaction code.  This makes the header consistent with that of
received PHY packets, and allows at_context_queue_packet() and
log_ar_at_event() to see the packet type directly instead of having
to deduce it from the header length or even from the header contents.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

To remove the error information from the controller's queue and to allow
more posted writes, the driver has to read the failed posted write
address before clearing the postedWriteErr interrupt bit.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

(Stefan R:) The spec is somewhat fuzzy about the actual requirements.
To err on the safe side, let's do these two read accesses.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Make sure that interrupt event clear bit writes are executed before the
interrupt handler returns.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Add proper error handling for the context_init() calls.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Move the AR DMA descriptors out of the buffer pages, and map the buffer
pages linearly into the kernel's address space.  This allows the driver
to ignore any page boundaries in the DMA data and thus to avoid any
copying around of packet payloads.

This fixes the bug where S800 packets that are so big (> 4080 bytes)
that they can be split over three pages were not handled correctly.

Due to the changed algorithm, we can now use arbitrarily many buffer
pages, which improves performance because the controller can more easily
unload its DMA FIFO.

Furthermore, using streaming DMA mappings should improve perfomance on
architectures where coherent DMA mappings are not cacheable.  Even on
other architectures, the caching behaviour should be improved slightly
because the CPU no longer writes to the buffer pages.

v2: Detect the last filled buffer page by searching the descriptor's
    residual count value fields in order (like in the old code), instead
    of going backwards through the transfer status fields; it looks as
    if some controllers do not set the latter correctly.

v3: Fix an old resume bug that would now make the handler run into
    a BUG_ON, and replace that check with more useful error handling.
    Increase the buffer size for better performance with non-TI chips.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Maxim Levitsky writes:
    Works almost perfectly.  I can still see RCODE_BUSY errors
    sometimes, not very often though.  64K here eliminates these errors
    completely.  This is most likely due to nouveau drivers and lowest
    perf level I use to lower card temperature.  That increases
    latencies too much I think.  Besides that the IO is just perfect.
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Add missing newlines.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Amend .open handler accordingly and remove the .llseek handler.
.llseek = NULL means no_llseek (return error) since commit 776c163b.

The only client that uses this interface is nosy-dump in linux/tools/firewire
and it knows not to seek in this char dev.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Agere FW643 rev 06, listed as "11c1:5901 (rev 06) (prog-if 10 [OHCI])",
produced SBP-2 I/O errors since kernel 2.6.36.  Disabling MSI fixes it.

Since MSI work on Agere FW643-E (same vendor and device ID, but rev 07),
introduce a device revision field into firewire-ohci's quirks list so
that different quirks can be defined for older and newer revisions.
Reported-by: NJonathan Isom <jeisom@gmail.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org> # 2.6.36.y

"VIA Technologies, Inc. VT6315 Series Firewire Controller [1106:3403]"
does not generate any interrupts if Message Signaled Interrupts were
enabled.  This is a regression since kernel 2.6.36 in which MSI support
was added to firewire-ohci.  Hence blacklist MSI on all VIA controllers.
Reported-by: NRobin Cook <rcook@wyrms.net>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org> # 2.6.36.y

This prevents firewire-net from submitting write requests in fast
succession until failure due to all 64 transaction labels were used up
for unfinished split transactions.  The netif_stop/wake_queue API is
used for this purpose.

Without this stop/wake mechanism, datagrams were simply lost whenever
the tlabel pool was exhausted.  Plus, tlabel exhaustion by firewire-net
also prevented other unrelated outbound transactions to be initiated.

The chosen queue depth was checked by me to hit the maximum possible
throughput with an OS X peer whose receive DMA is good enough to never
reject requests due to busy inbound request FIFO.  Current Linux peers
show a mixed picture of -5%...+15% change in bandwidth; their current
bottleneck are RCODE_BUSY situations (fewer or more, depending on TX
queue depth) due to too small AR buffer in firewire-ohci.

Maxim Levitsky tested this change with similar watermarks with a Linux
peer and some pending firewire-ohci improvements that address the
RCODE_BUSY problem and confirmed that these TX queue limits are good.

Note:  This removes some netif_wake_queue from reception code paths.
They were apparently copy&paste artefacts from a nonsensical
netif_wake_queue use in the older eth1394 driver.  This belongs only
into the transmit path.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>

The current transmit code does not at all make use of
  - fwnet_device.packet_list
and only very limited use of
  - fwnet_device.broadcasted_list,
  - fwnet_device.queued_packets.
Their current function is to track whether the TX soft-IRQ finished
dealing with an skb when the AT-req tasklet takes over, and to discard
pending tx datagrams (if there are any) when the local node is removed.

The latter does actually contain a race condition bug with TX soft-IRQ
and AT-req tasklet.

Instead of these lists and the corresponding link in fwnet_packet_task,
  - a flag in fwnet_packet_task to track whether fwnet_tx is done,
  - a counter of queued datagrams in fwnet_device
do the job as well.

The above mentioned theoretic race condition is resolved by letting
fwnet_remove sleep until all datagrams were flushed.  It may sleep
almost arbitrarily long since fwnet_remove is executed in the context of
a multithreaded (concurrency managed) workqueue.

The type of max_payload is changed to u16 here to avoid waste in struct
fwnet_packet_task.  This value cannot exceed 4096 per IEEE 1394:2008
table 16-18 (or 32678 per specification of packet headers, if there is
ever going to be something else than beta mode).
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

a) fwnet_transmit_packet_done used to poison ptask->pt_link by list_del.
If fwnet_send_packet checked later whether it was responsible to clean
up (in the border case that the TX soft IRQ was outpaced by the AT-req
tasklet on another CPU), it missed this because ptask->pt_link was no
longer shown as empty.

b) If fwnet_write_complete got an rcode other than RCODE_COMPLETE, we
missed to free the skb and ptask entirely.

Also, count stats.tx_dropped and stats.tx_errors when rcode != 0.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.

The patch below presents a simple SCSI host lock push-down as an
equivalent transformation.  No locking or other behavior should change
with this patch.  All existing bugs and locking orders are preserved.

Additionally, add one parameter to queuecommand,
	struct Scsi_Host *
and remove one parameter from queuecommand,
	void (*done)(struct scsi_cmnd *)

Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.

Minimal code disturbance was attempted with this change.  Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Acked-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the controller is storing a split packet and therefore changing
d->res_count to zero between the two reads by the driver, we end up with
an end pointer that is not at a packet boundary, and therefore overflow
the buffer when handling the split packet.

To fix this, read the field once, atomically.  The compiler usually
merges the two reads anyway, but for correctness, we have to enforce it.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Freeing an AR buffer page just to allocate a new page immediately
afterwards is not only a pointless effort but also dangerous because
the allocation can fail, which would result in an oops later.

Split ar_context_add_page() into two functions so that we can reuse
the old page directly.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

When handling an AR buffer that has been completely filled, we assumed
that its descriptor will not be read by the controller and can be
overwritten.  However, when the last received packet happens to end at
the end of the buffer, the controller might not yet have moved on to the
next buffer and might read the branch address later.  If we overwrite
and free the page before that, the DMA context will either go dead
because of an invalid Z value, or go off into some random memory.

To fix this, ensure that the descriptor does not get overwritten by
using only the actual buffer instead of the entire page for reassembling
the split packet.  Furthermore, to avoid freeing the page too early,
move on to the next buffer only when some data in it guarantees that the
controller has moved on.

This should eliminate the remaining firewire-net problems.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Cc: 2.6.22-2.6.36 <stable@kernel.org>
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

When the controller had to split a received asynchronous packet into two
buffers, the driver tries to reassemble it by copying both parts into
the first page.  However, if size + rest > PAGE_SIZE, i.e., if the yet
unhandled packets before the split packet, the split packet itself, and
any received packets after the split packet are together larger than one
page, then the memory after the first page would get overwritten.

To fix this, do not try to copy the data of all unhandled packets at
once, but copy the possibly needed data every time when handling
a packet.

This gets rid of most of the infamous crashes and data corruptions when
using firewire-net.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Cc: 2.6.22-2.6.36 <stable@kernel.org>
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (cast PAGE_SIZE to size_t)

Revert commit 54672386
"firewire: ohci: fix up configuration of TI chips".
It caused massive slow-down and data corruption with a TSB82AA2 based
StarTech EC1394B2 ExpressCard and FireWire 800 harddisks.

https://bugs.launchpad.net/ubuntu/+source/linux/+bug/657081
http://thread.gmane.org/gmane.linux.kernel.firewire.user/4013

The fact that some card EEPROMs do not program these enhancements may be
related to TSB81BA3 phy chip errata, if not to bugs of TSB82AA2 itself.
We could re-add these configuration steps, but only conditional on a
whitelist of cards on which these enhancements bring a proven positive
effect.
Reported-and-tested-by: NEric Shattow <lucent@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org> 2.6.35
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.

The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.

New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time.  Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.

The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.

Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.

Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.

===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
//   but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}

@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}

@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
   *off = E
|
   *off += E
|
   func(..., off, ...)
|
   E = *off
)
...+>
}

@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}

@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
  *off = E
|
  *off += E
|
  func(..., off, ...)
|
  E = *off
)
...+>
}

@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}

@ fops0 @
identifier fops;
@@
struct file_operations fops = {
 ...
};

@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
 .llseek = llseek_f,
...
};

@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
 .read = read_f,
...
};

@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
 .write = write_f,
...
};

@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
 .open = open_f,
...
};

// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
...  .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};

@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
...  .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};

// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
...  .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};

// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};

// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};

@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+	.llseek = default_llseek, /* write accesses f_pos */
};

// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////

@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
 .write = write_f,
 .read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};

@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};

@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};

@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>

The drivers
  - ohci1394 (controller driver)
  - ieee1394 (core)
  - dv1394, raw1394, video1394 (userspace ABI)
  - eth1394, sbp2 (protocol drivers)
are replaced by
  - firewire-ohci (controller driver)
  - firewire-core (core and userspace ABI)
  - firewire-net, firewire-sbp2 (protocol drivers)
which are more featureful, better performing, and more secure than the older
drivers; all with a smaller and more modern code base.

The driver firedtv in drivers/media/dvb/firewire/ contains backends to both
ieee1394 and firewire-core.  Its ieee1394 backend code can be removed in an
independent commit; firedtv as-is builds and works fine without ieee1394.

The driver pcilynx (an incomplete controller driver) is deleted without
replacement since PCILynx cards are extremely rare.  Owners of these cards
use them with the stand-alone bus sniffer driver nosy instead.

The drivers nosy and init_ohci1394_dma which do not interact with either of
the two IEEE 1394 stacks are not affected by the ieee1394 subsystem removal.

There are still some issues with the newer firewire subsystem compared to
the older one:
  - The rare and quirky controllers ALi M52xx, Apple UniNorth v1, NVIDIA
    NForce2 are even less well supported by firewire-ohci than by ohci1394.
    I am looking into the M52xx issue.
  - The experimental firewire-net is reportedly less stable than its
    experimental cousin eth1394.
  - Audio playback of a certain group of audio devices (ones based on DICE
    chipset with EAP; supported by prerelease FFADO code) does not work yet.
    This issue is still under investigation.
  - There were some ieee1394 based out-of-the-mainline drivers.  Of them,
    only lisight, an audio driver for iSight webcams, seems still useful.
    Work is underway to reimplement it on top of firewire-core.

All these remainig issues are minor; they should not stand in the way of
overall better user experience of IEEE 1394 on Linux, together with a
reduction in support efforts and maintenance burden.  The coexistence of two
IEEE 1394 kernel driver stacks in the mainline since 2.6.22 shall end now,
as announced earlier this year.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

because drivers/ieee1394/ will be deleted.

Additional changes:
  - add some #include directives
  - adjust to use firewire/ohci.h instead of ieee1394/ohci1394.h,
    replace struct ti_ohci by a minimal struct ohci,
    replace quadlet_t from ieee1394_types.h by u32
  - two or three trivial stylistic changes
  - __iomem annotation
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The Ricoh FireWire controllers appear to have the non-atomic cycle
timer register access bug, so, activate the driver workaround by
default.

The behaviour was observed on:
Ricoh Co Ltd R5C552 IEEE 1394 Controller [1180:0552] and
Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832] (rev 04).
Signed-off-by: NHeikki Lindholm <holin@iki.fi>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

VIA VT6306, VIA VT6308, and NEC OrangeLink controllers do not write
packet event codes for received PHY packets (or perhaps write
evt_no_status, hard to tell).  Work around it by overwriting the
packet's ACK by ack_complete, so that upper layers that listen to PHY
packet reception get to see these packets.

(Also tested:  TI TSB82AA2, TI TSB43AB22/A, TI XIO2213A, Agere FW643,
JMicron JMB381 --- these do not exhibit this bug.)

Clemens proposed a quirks flag for that, IOW whitelist known misbehaving
controllers for this workaround.  Though to me it seems harmless enough
to enable for all controllers.

The log_ar_at_event() debug log will continue to show the original
status from the DMA unit.

Reported-by: Clemens Ladisch <clemens@ladisch.de> (VT6308)
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Because we might be in interrupt context, replace del_timer_sync() with
del_timer().  If the timer is already running, we know that it will
clean up the transaction, so we do not need to do any further processing
in the normal transaction handler.

Many thanks to Yong Zhang for diagnosing this.
Reported-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The incoming request hander fwnet_receive_packet() expects subsequent
datagram handling code to return non-zero on errors.  However, almost
none of the failure paths did so.  Fix them all.

(This error reporting is used to send and RCODE_CONFLICT_ERROR to the
sender node in such failure cases.  Two modes of failure exist:  Out of
memory, or firewire-net is unaware of any peer node to which a fragment
or an ARP packet belongs.  However, it is unclear whether a sender can
actually make use of such information.  A Linux peer apparently can't.
Maybe it should all be simplified to void functions.)
Reported-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Fix I/O stalls with some 4-bay RAID enclosures which are based on
OXUF936QSE:
  - Onnto dataTale RSM4QO, old firmware (not anymore with current
    firmware),
  - inXtron Hydra Super-S LCM, old as well as current firmware
when used in RAID-5 mode, perhaps also in other RAID modes.

The stalls happen during heavy or moderate disk traffic in periods that
are a multiple of 5 minutes, roughly twice per hour.  They are caused
by the target responding too late to an ORB_Pointer register write:
The target responds after Split_Timeout, hence firewire-core cancels
the transaction, and firewire-sbp2 fails the SCSI request.  The SCSI
core retries the request, that fails again (and again), hence SCSI core
calls firewire-sbp2's abort handler (and even the Management_Agent
register write in the abort handler has the transaction timeout
problem).

During all that, the process which issued the I/O is stalled in I/O
wait state.

Meanwhile, the target actually acts on the first failed SCSI request:
It responds to the ORB_Pointer write later (seen in the kernel log as
"firewire_core: Unsolicited response") and also finishes the SCSI
request with proper status (seen in the kernel log as "firewire_sbp2:
status write for unknown orb").

So let's just ignore RCODE_CANCELLED in the transaction callback and
wait for the target to complete the ORB nevertheless.  This requires
a small modification is sbp2_cancel_orbs(); it now needs to call
orb->callback() regardless whether fw_cancel_transaction() found the
transaction unfinished or finished.

A different solution is to increase Split_Timeout on the local node.
(Tested: 2000ms timeout; maybe 1000ms or something like that works too.
200ms is insufficient.  Standard is 100ms.)  However, I rather not do
this because any software on any node could change the Split_Timeout to
something unsuitable.  Or such a large Split_Timeout may be undesirable
for other purposes.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

When an ORB was canceled (Command ORB i.e. SCSI request timed out, or
Management ORB timed out), or there was a send error in the initial
transaction, we missed to drop one of the ORB's references and thus
leaked memory.

Background:
In total, we hold 3 references to each Operation Request Block:
  - 1 during sbp2_scsi_queuecommand() or sbp2_send_management_orb()
    respectively,
  - 1 for the duration of the write transaction to the ORB_Pointer or
    Management_Agent register of the target,
  - 1 for as long as the ORB stays within the lu->orb_list, until
    the ORB is unlinked from the list and the orb->callback was
    executed.

The latter one of these 3 references is finished
  - normally by sbp2_status_write() when the target wrote status
    for a pending ORB,
  - or by sbp2_cancel_orbs() in case of an ORB time-out,
  - or by complete_transaction() in case of a send error.
Of them, the latter two lacked the kref_put.

Add the missing kref_put()s.  Add comments to the gets and puts of
references for transaction callbacks and ORB callbacks so that it is
easier to see what is supposed to happen.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The driver name and bus address for a net_device can normally be found
through the driver model now.  Instead of requiring drivers to provide
this information redundantly through the ethtool_ops::get_drvinfo
operation, use the driver model to do so if the driver does not define
the operation.  Since ETHTOOL_GDRVINFO no longer requires the driver
to implement any operations, do not require net_device::ethtool_ops to
be set either.

Remove implementations of get_drvinfo and ethtool_ops that provide
only this information.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an at least theoretic race condition in which .start_iso etc.
could still be called between when the dummy driver is bound to the card
and when the children devices are being shut down.  Add dummy_start_iso
and friends.

On the other hand, .enable, .set_config_rom, .read_csr, write_csr do not
need to be implemented by the dummy driver, as commented.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>