The job ring init function creates a platform device for each job ring.
While the job ring is shutdown, e.g. while caam module removal, its
platform device was not being removed. This leads to failure while
reinsertion and then removal of caam module second time.

The following kernel crash dump appears when caam module is reinserted
and then removed again. This patch fixes it.

root@p4080ds:~# rmmod caam.ko
Unable to handle kernel paging request for data at address 0x00000008
Faulting instruction address: 0xf94aca18
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=8 P4080 DS
Modules linked in: caam(-) qoriq_dbg(O) [last unloaded: caam]
NIP: f94aca18 LR: f94aca18 CTR: c029f950
REGS: eac47d60 TRAP: 0300   Tainted: G           O  (3.8.4-rt2)
MSR: 00029002 <CE,EE,ME>  CR: 22022484  XER: 20000000
DEAR: 00000008, ESR: 00000000
TASK = e49dfaf0[2110] 'rmmod' THREAD: eac46000 CPU: 1
GPR00: f94ad3f4 eac47e10 e49dfaf0 00000000 00000005 ea2ac210 ffffffff 00000000
GPR08: c286de68 e4977ce0 c029b1c0 00000001 c029f950 10029738 00000000 100e0000
GPR16: 00000000 10023d00 1000cbdc 1000cb8c 1000cbb8 00000000 c07dfecc 00000000
GPR24: c07e0000 00000000 1000cbd8 f94e0000 ffffffff 00000000 ea53cd40 00000000
NIP [f94aca18] caam_reset_hw_jr+0x18/0x1c0 [caam]
LR [f94aca18] caam_reset_hw_jr+0x18/0x1c0 [caam]
Call Trace:
[eac47e10] [eac47e30] 0xeac47e30 (unreliable)
[eac47e20] [f94ad3f4] caam_jr_shutdown+0x34/0x220 [caam]
[eac47e60] [f94ac0e4] caam_remove+0x54/0xb0 [caam]
[eac47e80] [c029fb38] __device_release_driver+0x68/0x120
[eac47e90] [c02a05c8] driver_detach+0xd8/0xe0
[eac47eb0] [c029f8e0] bus_remove_driver+0xa0/0x110
[eac47ed0] [c00768e4] sys_delete_module+0x144/0x270
[eac47f40] [c000e2f0] ret_from_syscall+0x0/0x3c
Signed-off-by: NVakul Garg <vakul@freescale.com>
Signed-off-by: NBharat Bhushan <bharat.bhushan@freescale.com>
Reviewed-by: NHoria Geanta <horia.geanta@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Patch adds AVX2/AES-NI/x86-64 implementation of Camellia cipher, requiring
32 parallel blocks for input (512 bytes). Compared to AVX implementation, this
version is extended to use the 256-bit wide YMM registers. For AES-NI
instructions data is split to two 128-bit registers and merged afterwards.
Even with this additional handling, performance should be higher compared
to the AES-NI/AVX implementation.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Patch adds AVX2/x86-64 implementation of Serpent cipher, requiring 16 parallel
blocks for input (256 bytes). Implementation is based on the AVX implementation
and extends to use the 256-bit wide YMM registers. Since serpent does not use
table look-ups, this implementation should be close to two times faster than
the AVX implementation.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Patch adds AVX2/x86-64 implementation of Twofish cipher, requiring 16 parallel
blocks for input (256 bytes). Table look-ups are performed using vpgatherdd
instruction directly from vector registers and thus should be faster than
earlier implementations. Implementation also uses 256-bit wide YMM registers,
which should give additional speed up compared to the AVX implementation.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Patch adds AVX2/x86-64 implementation of Blowfish cipher, requiring 32 parallel
blocks for input (256 bytes). Table look-ups are performed using vpgatherdd
instruction directly from vector registers and thus should be faster than
earlier implementations.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The Kconfig setting for glue helper module is CRYPTO_GLUE_HELPER_X86, but
recent change for aesni_intel used CRYPTO_GLUE_HELPER instead. Patch corrects
this issue.

Cc: kbuild-all@01.org
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Add more optimized XTS code for aesni_intel in 64-bit mode, for smaller stack
usage and boost for speed.

tcrypt results, with Intel i5-2450M:
256-bit key
        enc     dec
16B     0.98x   0.99x
64B     0.64x   0.63x
256B    1.29x   1.32x
1024B   1.54x   1.58x
8192B   1.57x   1.60x

512-bit key
        enc     dec
16B     0.98x   0.99x
64B     0.60x   0.59x
256B    1.24x   1.25x
1024B   1.39x   1.42x
8192B   1.38x   1.42x

I chose not to optimize smaller than block size of 256 bytes, since XTS is
practically always used with data blocks of size 512 bytes. This is why
performance is reduced in tcrypt for 64 byte long blocks.

Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Add more optimized XTS code for camellia-aesni-avx, for smaller stack usage
and small boost for speed.

tcrypt results, with Intel i5-2450M:
        enc     dec
16B     1.10x   1.01x
64B     0.82x   0.77x
256B    1.14x   1.10x
1024B   1.17x   1.16x
8192B   1.10x   1.11x

Since XTS is practically always used with data blocks of size 512 bytes or
more, I chose to not make use of camellia-2way for block sized smaller than
256 bytes. This causes slower result in tcrypt for 64 bytes.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Change cast6-avx to use the new XTS code, for smaller stack usage and small
boost to performance.

tcrypt results, with Intel i5-2450M:
        enc     dec
16B     1.01x   1.01x
64B     1.01x   1.00x
256B    1.09x   1.02x
1024B   1.08x   1.06x
8192B   1.08x   1.07x
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Change twofish-avx to use the new XTS code, for smaller stack usage and small
boost to performance.

tcrypt results, with Intel i5-2450M:
        enc     dec
16B     1.03x   1.02x
64B     0.91x   0.91x
256B    1.10x   1.09x
1024B   1.12x   1.11x
8192B   1.12x   1.11x

Since XTS is practically always used with data blocks of size 512 bytes or
more, I chose to not make use of twofish-3way for block sized smaller than
128 bytes. This causes slower result in tcrypt for 64 bytes.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch adds AVX optimized XTS-mode helper functions/macros and converts
serpent-avx to use the new facilities. Benefits are slightly improved speed
and reduced stack usage as use of temporary IV-array is avoided.

tcrypt results, with Intel i5-2450M:
        enc     dec
16B     1.00x   1.00x
64B     1.00x   1.00x
256B    1.04x   1.06x
1024B   1.09x   1.09x
8192B   1.10x   1.09x
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Now that CryptoAPI has support for CMAC, we can add support for AES-CMAC-96
(rfc4494).

Cc: Tom St Denis <tstdenis@elliptictech.com>
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Patch adds support for NIST recommended block cipher mode CMAC to CryptoAPI.

This work is based on Tom St Denis' earlier patch,
 http://marc.info/?l=linux-crypto-vger&m=135877306305466&w=2

Cc: Tom St Denis <tstdenis@elliptictech.com>
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Without these, kernel log shows:
[    5.984881] alg: No test for cipher_null (cipher_null-generic)
[    5.985096] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[    5.985170] alg: No test for compress_null (compress_null-generic)
[    5.985297] alg: No test for digest_null (digest_null-generic)
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

If the gcm cipher used by rfc4543 does not complete request immediately,
the authentication tag is not copied to destination buffer. Patch adds
correct async logic for this case.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The GMAC code assumes that dst==src, which causes problems when trying to add
rfc4543(gcm(aes)) test vectors.

So fix this code to work when source and destination buffer are different.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch allows timeriomem_rng to be used via devicetree.
Signed-off-by: NAlexander Clouter <alex@digriz.org.uk>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

timeriomem_rng only supports a single device instance.  This patch
enables multiple timeriomem_rng devices to coexist as well as adds
some additional error checking.
Signed-off-by: NAlexander Clouter <alex@digriz.org.uk>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Occurs when CONFIG_CRYPTO_CRC32C_INTEL=y and CONFIG_CRYPTO_CRC32C_INTEL=y.
Older versions of bintuils do not support the pclmulqdq instruction. The
PCLMULQDQ gas macro is used instead.
Signed-off-by: NSandy Wu <sandyw@twitter.com>
Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This adds a driver for random number generator present on Broadcom BCM2835 SoC,
used in Raspberry Pi and Roku 2 devices.
Signed-off-by: NDom Cobley <popcornmix@gmail.com>
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: linux-rpi-kernel@lists.infradead.org
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

checkstack reports report_deco_status(), report_ccb_status() as
particularly excessive stack users.  Move their lookup tables
off the stack and put them in .rodata.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

commit 2af8f4a2 "crypto: caam - coccicheck fixes" added error
return values yet neglected to change the type from unsigned.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

crypto: sha512 - Create module providing optimized SHA512 routines using SSSE3, AVX or AVX2 instructions.

We added glue code and config options to create crypto
module that uses SSE/AVX/AVX2 optimized SHA512 x86_64 assembly routines.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Provides SHA512 x86_64 assembly routine optimized with SSE, AVX and
AVX2's RORX instructions.  Speedup of 70% or more has been
measured over the generic implementation.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Provides SHA512 x86_64 assembly routine optimized with SSE and AVX instructions.
Speedup of 60% or more has been measured over the generic implementation.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Provides SHA512 x86_64 assembly routine optimized with SSSE3 instructions.
Speedup of 40% or more has been measured over the generic implementation.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Other SHA512 routines may need to use the generic routine when
FPU is not available.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

crypto: sha256 - Create module providing optimized SHA256 routines using SSSE3, AVX or AVX2 instructions.

We added glue code and config options to create crypto
module that uses SSE/AVX/AVX2 optimized SHA256 x86_64 assembly routines.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Provides SHA256 x86_64 assembly routine optimized with SSE, AVX and
AVX2's RORX instructions.  Speedup of 70% or more has been
measured over the generic implementation.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Provides SHA256 x86_64 assembly routine optimized with SSE and AVX instructions.
Speedup of 60% or more has been measured over the generic implementation.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Provides SHA256 x86_64 assembly routine optimized with SSSE3 instructions.
Speedup of 40% or more has been measured over the generic implementation.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Other SHA256 routine may need to use the generic routine when
FPU is not available.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

These modules require AVX support in assembler, so add new check to Makefile
for this.

Other option would be to use CONFIG_AS_AVX inside source files, but that would
result dummy/empty/no-fuctionality modules being created.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Using devm_ioremap_resource() can make the code cleaner and simpler.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>