This change makes it a bit easier to do the loopback frame creating and
testing.  Previously we were doing an and to drop the last bit, and then
dividing the frame_size by 2 in order to get locations for frame bytes and
testing.  Instead we can simplify it by just shifting the register one bit
to the right and using that for the frame offsets.

This change also replaces all instances of rx_buffer_info with just
rx_buffer since that is closer to the name of the actual structure being
used and can save a few extra characters.

In addition I have updated the logic for cleaning up a test frame so that
we pass an rx_buffer instead of the sk_buff.  The main motivation behind
this is changes that will replace the sk_buff with just a page in the
future.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes the rings a part of the q_vector directly instead of
indirectly.  Specifically on x86 systems this helps to avoid any cache
set conflicts between the q_vector, the tx_rings, and the rx_rings as the
critical stride is 4K and in order to cross that boundary you would need to
have over 15 rings on a single q_vector.

In addition this allows for smarter allocations when Flow Director is
enabled.  Previously Flow Director would set the irq_affinity hints based
on the CPU and was still using a node interleaving approach which on some
systems would end up with the two values mismatched.  With the new approach
we can set the affinity for the irq_vector and use the CPU for that
affinity to determine the node value for the node and the rings.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As noted by Ben Hutchings and David Miller, work limits for NAPI
should not be tied to interrupt moderation parameters.  This
should be handled by NAPI, possibly through sysfs.

Neil Horman & Stephen Hemminger are working on a solution for
NAPI currently.  In the meantime, remove this tie between
work limits and interrupt moderation.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>

It doesn't make much sense to differentiate between advanced and legacy
descriptors when the only descriptors that ixgbe uses are advanced
descriptors.  As such we can drop the _ADV suffix since all ixgbe
descriptors are automatically advanced.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the number of tx/rx queues changes the ethtool ioctl
ETHTOOL_GSTATS may overrun the userspace buffer. This
occurs because the general practice in user space to
query stats is to issue a ETHTOOL_GSSET cmd to learn the
buffer size needed, allocate the buffer, then call
ETHTOOL_GSTIRNGS and ETHTOOL_GSTATS. If the number of
real_num_queues is changed or flow control attributes
are changed after ETHTOOL_GSSET but before the
ETHTOOL_GSTRINGS/ETHTOOL_GSTATS a user space buffer
overrun occurs.

To fix the overrun always return the max buffer size
needed from get_sset_count() then return all strings
and stats from get_strings()/get_ethtool_stats().

This _will_ change the output from the ioctl() call
which could break applications and script parsing in
theory. I believe these changes should not break existing
tools because the only changes will be more {tx|rx}_queues
and the {tx|rx}_pb_* stats will always be returned.
Existing scripts already need to handle changing number
of queues because this occurs today depending on system
and current features. The {tx|rx}_pb_* stats are at the
end of the output and should be handled by scripts today
regardless.

Finally get_ethtool_stats and get_strings are free-form
outputs tools parsing these outputs should be defensive
anyways. In the end these updates are better then
having a tool segfault because of a buffer overrun.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

New year so bump the copyright date.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This device uses an already existing DevID but since it supports
WoL we need to add the Sub DevID.  It's support of WoL is limited
to the first port.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This round of floor sweeping converts strncpy calls in various .get_drvinfo
routines to the preferred strlcpy.  It also does a modicum of other
cleaning in those routines.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use 32bit value starting at offset 0x2d for displaying the firmware
version in ethtool. This should work for all current ixgbe HW
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement support for ethtool -E
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add 2 new counters to ethtool:
	1. Count DDP allocation failure since we max the number of buffers
		allowed in one DDP context.
	2. Count DDP allocation failure since we max the number of buffers
		allowed in one DDP context when we alloc an extra buffer.
Signed-off-by: NAmir Hanania <amir.hanania@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a problem in the ixgbe driver with the reporting of the flow
control parameters. The autoneg parameter is shown to be of if
*either* it really is off, or current modes for both tx and rx are off.

The problem is seen when the parameters are read or set when the link
is down. In this case, the driver sees that tx and rx are currently off
and therefore autoneg parameter is incorrectly reported to be off too.
Also, the ethtool binary can not set the autoneg off since it sees that
it already is. When a link later comes up, the autonegotiation is
carried out normally and the driver later on reports the autoneg
parameter to be on (as it is) and then it can also be changed with
ethtool.

The patch is made against v3.0 kernel, but the problem seems to be there
since v2.6.30-rc1.

Reviewer comments: What we are trying to do is to disable flow control
while the cable is disconnected. Since ixgbe defaults to full flow
control, we call ethtool -A autoneg off rx off tx off while the cable
is disconnected. This doesn't work, because the driver sets
hw->fc.current_mode = ixgbe_fc_none if the cable is unplugged.
ixgbe_get_pauseparam() then reports to ethtool that nothing needs to be
done. The code fixes this, but it might have some unknown consequences.
Signed-off-by: NMika Lansirinne <mika.lansirinne@stonesoft.com>
Reviewed-by: NEsa-Pekka Pyokkimies <esa-pekka.pyokkimies@stonesoft.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

MFLCN register is used to set Rx flow control on parts newer than 82598.

This patch sends the value of MFLCN to ethtool, so it can be used in a
register dump (ethtool -d).
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to help cleanup the interrupt throttle rate logic by
storing the interrupt throttle rate as a value in microseconds instead of
interrupts per second.  The advantage to this approach is that the value
can now be stored in an 16 bit field and doesn't require as much math to
flip the value back and forth since the hardware already used microseconds
when setting the rate.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for WOL as determined by the EEPROM.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch improves the memory utilization with RSC when in one-buffer
mode.  This is accomplished by making the default buffer sizes match up
with the standard memory allocation sizes minus 1K for shared info and
padding overhead.  By doing this CPU utilization when doing large receives
can be reduced by as much as 8%.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A user-space process must use ETHTOOL_GRXCLSRLCNT to find the number
of classification rules, then allocate a buffer of the right size,
then use ETHTOOL_GRXCLSRLALL to fill the buffer.  If some other
process inserts or deletes a rule between those two operations,
the user buffer might turn out to be the wrong size.

If it's too small, the return value will be -EMSGSIZE.  But if it's
too large, there is no indication of this.  Fix this by updating
the rule_cnt field on return.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.

Add note that drivers must not use ethtool_rxnfc::rule_locs.

The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch drops a set of unnecessary dereferences to the hardware structure
since we already have a local copy of the hardware pointer.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When setting advertised speed/duplex with ethtool.

Also cleaned up the comment since we also support 100/F.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

after review of all intel drivers, found several instances where
drivers had the incorrect pattern of:
memory mapped write();
delay();

which should always be:
memory mapped write();
write flush(); /* aka memory mapped read */
delay();

explanation:
The reason for including the flush is that writes can be held
(posted) in PCI/PCIe bridges, but the read always has to complete
synchronously and therefore has to flush all pending writes to a
device.  If a write is held and followed by a delay, the delay
means nothing because the write may not have reached hardware
(maybe even not until the next read)
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Private rx_csum flags are now duplicate of netdev->features &
NETIF_F_RXCSUM.  We remove those duplicates and now use the net_device_ops
ndo_set_features.  This was based on the original patch submitted by
Michal Miroslaw <mirq-linux@rere.qmqm.pl>.  I also removed the special
case not requiring a reset for X540 hardware.  It is needed just as it is
in 82599 hardware.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Cc:  Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change moves work_limit, total_packets, and total_bytes into the ring
container struct of the q_vector.  The advantage of this is that it should
reduce the size of memory used in the event of multiple rings being
assigned to a single q_vector.  In addition it should help to reduce the
total workload for calculating itr since now total_packets and total_bytes
will be the total work done of the interrupt instead of for the ring.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for a ring container structure to be used within
the q_vector.  The basic idea is to provide a means of separating the RX
and TX rings while maintaining a common structure for their containment.
The advantage to this is that later we should be able to pass this
structure to the update_itr functions without needing to pass individual
rings.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes the fact that we would trigger a null pointer dereference
or specify the wrong ring if the rings were restored.  This change makes
certain that the DROP queue is a static value, and all other rings are
based on the ring offsets for the PF.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Disabling Rx checksumming leads to performance degradation due to
RSC causing packets to have incorrect checksums.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move reset code into a separate function to allow for reuse in other
parts of the code.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move setting RSC into a separate function to allow for reuse in other
parts of the code.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to allow for nfc to insert and remove filters in order
to test the ethtool interface which includes it's own rules manager.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This code adds support for displaying the filters that were added via the
nfc interface.  This is primarily to test the interface for now, but I am
also looking into the feasibility of moving all of the ntuple filter code
in ixgbe over to the nfc interface since it seems to be better implemented.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds basic support for the obtaining of RSS ring counts.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I am removing the requirement that Ntuple filters have the same
number of queues and requirements as ATR.  As a result this change will
make it so that all the Ntuple flag does is disable ATR for now.

This change fixes an issue in which we were incorrectly re-enabling ATR
when we exited perfect filter mode.  This was due to the fact that the
logic assumed RSS and DCB were mutually exclusive which is no longer the
case.

To correct this we just need to add a check to guarantee DCB is disabled
before re-enabling ATR.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to numerous issues in ntuple filters it has been decided to move the
interface over to the network flow classification interface.  As a first
step to achieving this I first need to remove the old ntuple interface.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change merges the ATR table reinitialization into the service task.
This is yet another opportunity to avoid any race conditions as we don't
want to be attempting to reinitialize the table during a possible reset.

In addition this change adds a counter for table reinitialization so that
it can be tracked as part of the regular statistics.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

OS2BMC registers are available for X540.
This patch adds ethtool counters based on those registers.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>