Signed-off-by: NEnrico Scholz <enrico.scholz@sigma-chemnitz.de>
Acked-by: NSebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

According to Alan Stern, short packets are quite normal under
certain circumstances. This printk was triggered by usb to
serial converters on every packet and some usb sticks triggered
a few of those while plugging the stick.
This printks are now hidden unless USB debug mode is activated.

Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ISP1760 requires a delay of 90ns between programming the address and
reading the data.  Current driver solves this by a mdelay(1) which is
very heavy weighted and slow.  This patch applies the workaround from
the ISP1760 FAQ by using two different banks for PTD and payload data
and using a common wait for them.  This wait is done by an additional
ISP1760 access (whose timing constraints guarantee the 90ns delay).
This improves speed when reading from an USB stick from:

  $ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
  real    1m 15.43s
  user    0m 0.44s
  sys     0m 39.46s

to

  $ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
  real    0m 18.53s
  user    0m 0.16s
  sys     0m 12.97s

[bigeasy@linutronix.de: fixed comment formating, moved define into
   header file, obey 80 char rule]
Signed-off-by: NEnrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

if the enqueue function returns -ESHUTDOWN or -ENOMEM then
we return 0 instead of an error. This leads to a timeout and
then to a dequeue request of an not enqueued urb.
Signed-off-by: NSebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds support for hardware configurations that don't match the
chip default register settings (e.g., 16-bit data bus, DACK and
DREQ pulled up instead of down, analog overcurrent mode).

These settings are passed in via the OF device tree.  The PCI
interface still assumes the same default values.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes the following needlessly global functions static:
- enqueue_an_ATL_packet()
- enqueue_an_INT_packet()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bus_id field is going away, use the dev_set_name() function
to set it properly.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes the bogus "io mem 0x00000000" message printed
during driver init due to hcd->rsrc_start being assigned after
the call to usb_add_hcd().
Signed-off-by: NNate Case <ncase@xes-inc.com>
Acked-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix printk format warnings in isp1760 (in linux-next):

next-20080430/drivers/usb/host/isp1760-hcd.c:994: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
next-20080430/drivers/usb/host/isp1760-hcd.c:1092: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver has been written from scratch and supports the ISP1760. ISP1761
might (should) work as well but the OTG isn't supported. Also ISO packets are
not. However, it works on my little PowerPC board.
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>