The MDIO bus cannot be accessed at interrupt context, but on an FEC
error, the fec_mpc52xx driver reset function also tries to reset the
PHY.  Since the error is detected at IRQ context, and the PHY functions
try to sleep, the kernel ends up panicking.

Resetting the PHY on an FEC error isn't even necessary.  This patch
solves the problem by removing the PHY reset entirely.
Signed-off-by: NJohn Bonesio <bones@secretlab.ca>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some OF platform drivers are missing module device tables, so they won't
load automatically on boot. This patch fixes the issue by adding proper
MODULE_DEVICE_TABLE() macros to the drivers.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mechanism to clear the statistics register is dependent
on the status of GMIIEN bit in MAC control register. If the
GMIIEN bit is set, the stats registers are write to decrement.
If the GMIIEN bit is cleared, the stats registers are plain
read/write registers. The stats register clearing operation
must take into account the current state of GMIIEN as it
can be cleared when the interface is brought down.

With existing implementation logic, querying for interface stats
when the interface is down, can corrupt the statistics counters.
This patch examines the GMIIEN bit status in MAC_CONTROL
register before choosing an appropriate mask for clearing stats
registers.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Acked-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extracted from Realtek's 8.012.00 r8168 driver.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NSimon Farnsworth <simon.farnsworth@onelan.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cisco HDLC uses keepalive packets and sequence numbers to determine link
state. In rare cases both ends could transmit keepalive packets at the same
time, causing the received sequence numbers to be treated as incorrect.
Now we accept our current sequence number as well as the previous one.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

3c574_cs:
 spin_lock the set_multicast_list function.
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Belkin F8T012xx1 bluetooth adaptor has the same vendor and product
IDs as the Belkin F5D5050, so we need to teach the pegasus driver to
ignore adaptors belonging to the "Wireless" class 0xE0. For this one
case anyway, seeing as pegasus is a driver for "Wired" adaptors.
Signed-off-by: NChris Rankin <rankincj@yahoo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use resource_size_t for PCI resource remapping instead
of unsigned long. Physical addresses can exceed range of
long data type (e.g with PAE).
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethoc.c: In function ‘ethoc_open’:
drivers/net/ethoc.c:667: warning: comparison of distinct pointer types
lacks a cast
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethernet NIC driver for VMware's vmxnet3

From: Shreyas Bhatewara <sbhatewara@vmware.com>

This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3
Guests running on VMware hypervisors supporting vmxnet3 device will thus have
access to improved network functionalities and performance.
Signed-off-by: NShreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NBhavesh Davda <bhavesh@vmware.com>
Signed-off-by: NRonghua Zhang <ronghua@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IXP 2000 network driver was failing to build as it has its own
statistics gathering which was not compatible with the recent network
device operations changes. This patch fixes the driver in the obvious
way and has been compile tested. I have been unable to get the ixp2000
maintainer to comment or test this fix.
Signed-off-by: NVincent Sanders <vince@simtec.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to the way it interacts with the networking
stack and other parts of mac80211, ieee80211_rx()
must be called with disabled softirqs.

[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/39440/focus=40266Reported-by: NDave Young <hidave.darkstar@gmail.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Need to free the dynamic allocated memory before ieee80211_free_hw();
once call ieee80211_free_hw(), should not reference to "priv" data
structure.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If ace_load_firmware() fails, ace_init() cleans up but still returns
0, leading to an oops as seen in <http://bugs.debian.org/521383>.
It should pass the error code up.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need PHY drivers to initialize in a static kernel before
the MAC drivers that use them.  So link them in first.

Based upon a report by Felix Radensky.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the EMAC V4 implementations support 16K Tx FIFOs. This
patch adds support for this functionality and fixes typos in the
Tx FIFO size error messages.
Signed-off-by: NDave Mitchell <dmitchell@appliedmicro.com>
Acked-by: NProdyut Hazarika <phazarika@appliedmicro.com>
Acked-by: NVictor Gallardo <vgallardo@appliedmicro.com>
Acked-by: NLoc Ho <lho@appliedmicro.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was accidentally omitted from one of the previous patches for firmware event
handling.  The handler needs to the enable firmware irq mask when it's done
processing or it may not get any more events interrupts.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call set_multi API after reset recovery.  This was exposed by tripping
tx_timeout.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add wait for NIC fifo and MGMNT fifo to empty before applying reset.
Otherwise broken frames can be processed by management processor and
cause it to hang.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The addresses were being added to the filter properly, but were not
being enabled.  This adds enable bit to filter write.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcast/multicast should always be routed to the default (zeroeth) rx
ring.  Broadcast frames are already routed correctly.  This fixes
routing for multicast frames.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently frames are routed based on their type and MAC address. This
patch adds the port number on which the frame arrived to the routing.
This prevents problems in the case where both interfaces have the same MAC address in
a routing configuration.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix RX queue table size and change from random to default hash values.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's not necessary and it's illegal too.
Reported-by: NAlexander Strakh <strakh@ispras.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DMA-API debugging facility complains about b43 mapping memory from
stack for SDIO-based cards.

Indeed, b43 currently allocates the PIO RX/TX header and tail buffers
from stack. The solution here is to use heap-allocated buffers instead.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In Bugzilla No. 14181, a PowerMac G4 crashes on ifdown or
module unload because the rfkill polling has not been stopped.
For the x86 architectures, the attempt to reach a now unmapped
register is not fatal as it is on PPC.

(Includes "b43: Fix locking problem when stopping rfkill polling". -- JWL)
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A logical of shifts to the left doesn't make sense.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

User-visible messages should use formatted MAC addresses ("00:01:...")
rather than raw ("0001...") so they match other parts of the system.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
CC: ilw@linux.intel.com
CC: linux-wireless@vger.kernel.org
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix IRQ mask sanity check for physically pulled device.
Tested-by: NAndrew Price <andy@andrewprice.me.uk>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The return type of abs() was recently changed from int to long. With
min()'s type checking we thus need to make sure that values of the same
type are compared.

This fixes:

    CC [M]  drivers/net/wireless/iwlwifi/iwl-5000.o
drivers/net/wireless/iwlwifi/iwl-5000.c: In function ‘iwl5000_gain_computation’:
drivers/net/wireless/iwlwifi/iwl-5000.c:320: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Reported-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes following on big endian systems:
  CC [M]  drivers/net/wireless/iwlwifi/iwl-rx.o
  drivers/net/wireless/iwlwifi/iwl-rx.c: In function ‘iwl_rx_reply_rx’:
  drivers/net/wireless/iwlwifi/iwl-rx.c:1029: warning: integer overflow in
  expression
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Reported-by: NMarcel Holtmann <marcel@holtmann.org>
Tested-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set the correct EEPROM offset for enhance tx power for 6000 series
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The address stored in the next link address is a word address but when
reading the OTP blocks, a byte address is used. Also if the blocks are
full and the last link pointer is not zero, then none of the blocks are
valid so return an error.

The algorithm is simply valid blocks have a next address and that
address's contents is zero.

Using the wrong address for the next link address gets arbitrary data,
obviously. In cases seen, the first block is considered valid when it is not.

If the block has in fact been invalidated there may be old data or
there may be no data, bad data, or partial data, there is no way of
telling. Without this patch it is possible that a device with valid OTP data
is unable to work.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't use struct wldev after detach. This fixes an oops on access.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Only 128 buffer descriptors are supported in the core. Limit the
number in case we have more memory.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enabled the ethoc to allocate system memory as buffer
when there is no dedicated buffer memory.

Some hardware designs may not have dedicated buffer memory such as
on chip or off chip SRAM. In this case, only one memory resource is
supplied in the platform data instead of two. Then a DMA buffer can
be allocated from system memory and used for the transfer.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The packet buffer is allocated at 4 bytes boundary, but the IP header
length and version bits is located at byte 14. These bit fields access
as 32 bits word and caused exception on processors that do not support
unaligned access.

The patch adds 2 bytes offset to make the bit fields word aligned.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>