When using IBSS, it's easily possible to exhaust the number
of available stations in the driver, so don't warn on it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we load the firmware for the 8000 B step device, it'll
verify its signature. In the current version of the
hardware, there can be a race between the WiFi firmware
being loaded and the Bluetooth firmware being loaded.

Check that WiFi is authenticated, if not, take ownership
on the authentication machine to make sure that the WiFi
firmware will be authenticated.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New sub system IDs were introduced for the 8260 series.
This patch adds them so new 8260 cards can be recognized.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make the print a bit more readable.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the FW returns an invalid channels count in response to an MCC request,
make sure we don't reference invalid indices in the channels array.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When entering D0i3, the MVM mutex cannot be grabbed. This interferes
with the calculation of the number of connected TDLS stations during
the setup of the power cmd.
The goal is to disable power saving for all vifs while any TDLS station
is connected. For this purpose it is enough to keep the pm_enabled
member of all mvmvifs as false. An update of the power state already
occurs when a TDLS station is added/removed, so the values are correctly
updated.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

mvm->fw->dbg_dest_tlv really needs to be under the right
parenthesis.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The functions related to firmware error dump moved. No need
for this unclude anymore.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New NVM versions in LnP platforms have the lar_enable bits in a different
offset.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

While at it, fix a few checkpatch issues.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This adds BT Coex data to the prph register list.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We don't need to acquire MAC access for each access, it
makes much more sense to keep the MAC access. This speeds
up the Tx DMA stop flow significantly.
Moreover, if one channel can't be stopped, stop the others
but don't poll for them to avoid being stuck there for a
long time.

This solves a situation in which we were stuck in that flow
for way too long with a spinlock held which led to a kernel
panic.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In-order to recognize newer step of the device, the driver
must read the chip_version_id from the AUX bus MISC address
space. This will determine what firmware file will be
loaded.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we associate we always need to update the quotas. This
fixes a bug for cases in which quotas weren't udapted after
association.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enable this feature only if the firmware advertises support
for it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares support this API.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firwmares have this new API.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This new firmware will come out soon.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When moving to the D3 FW give it the valid MCC from the D0 FW. When
returning from D3 to D0, query the D3 FW for the latest MCC, as
it might have changed internally. This MCC will be replayed to the D0 FW
when it boots.
Signed-off-by: NJonathan Doron <jonathanx.doron@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When booting the card, check for a dedicated regulatory ACPI entry. If
such exists, read it and give the information to FW with the appropriate
source.
Signed-off-by: NJonathan Doron <jonathanx.doron@intel.com>
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For some configurations, the driver should get the MAC
address from the hardware registers and not from the
regular locations. Since the parsing of the MAC address
is the same regardless of its source, continue the regular
code path (parsing) after we read the registers.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This module parameter is useful for debugging NVM and LAR related issues.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Starting from family 8000 B0 step the radio_cfg parameters
and the get_sku parameters moved from SW section to PHY_SKU section.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

11ac depends on 11n, so disable it if 11n is disabled.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If LAR is supported in TLV, but the NVM does not enable it, then disable
LAR support and ignore the TLV's bit that enabled LAR.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

max_eirp affects the txpower configured to the power,
so use the max tx power (22) instead of some other
value.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix the last 5ghz channel to 165 instead of 161
Add support for 8000 family, until channel 181.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Otherwise the regulatory data will mistakenly contain only 7000 series
channels.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Chub (Communication Hub, CommsHUB) is a HW component that connects to the cellular
and connectivity cores that gets updates of mcc changes, and then notifies the FW
directly of any mcc change.

The ucode notifies the driver (via this command) that it should ask for an mcc update,
and the driver sends the ucode the update mcc command to set the updated regulatory info.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove a useless debug print about unsupported channels.
Also add a comment about the LAR special case where channels
might become valid later.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

According to updated regulatory guidelines, the ACTIVE bit in the NVM
also allows ibss activity on the channel. The IBSS NVM bit is not updated
when LAR is active and is deprecated. Using this bit for NO-IR incorrectly
causes all 5Ghz channels to be marked as passive.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Register to cfg80211 with all channels enabled when LAR is supported.
Appropriate channels will later be disabled when a specific regulatory
domain is defined.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Parse the NVM channel data and create a regulatory domain with a rule
for every 20Mhz channel. Use the AUTO_BW flag so the regulatory core
can unify single-channel rules into ranges.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

During init queue a regulatory update to retrieve the default
regulatory settings from FW. If we're during recovery, only replay the
current country code to FW, if it exists.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The new API sets an MCC (mobile country code) to FW and receives a
channel structure to be used as a basis for an updated regulatory domain.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The commit below didn't update the max_ht_ampdu_exponent
for the devices listed in iwl-[1-6]000.c which, in result,
became 0 instead of 8K. This reduced the size of the Rx
AMPDU from 64K to 8K which had an impact in the Rx
throughput. One user reported that because of this, his
downstream throughput droppped by a half.

CC: <stable@vger.kernel.org> [3.19]
Fixes: c064ddf3 ("iwlwifi: change max HT and VHT A-MPDU exponent")
Reported-and-tested-by: NValentin Manea <linux-wireless@mrs.ro>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The commits below broke compilation when
CONFIG_IWLWIFI_DEBUGFS is not set.
FIx that.

Fixes: ddf89ab1 ("iwlwifi: mvm: allow to force the Rx chains from debugfs")
Fixes: 9d761fd8 ("iwlwifi: mvm: add trigger for firmware dump upon missed beacons")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently scan params structure has only active or passive dwell time
fields, passive one is used for fragmented scans too. FW needs the
passive dwell time even when performing fragmented scan for calculating
time between channels. Add a separate parameter for fragmented dwell time
and pass both fragmented and passive to FW.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Lots of issues can be caught when the RSSI drops. Add the
ability to collect the firmware data at that point.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It can be very useful to monitor the statistics and trigger
a firmware dump when a certain value hits a certain offset.
Since the statistics are huge, add a generic trigger. When
the DWORD at offset X reaches value Y.

Since there is another trigger before this one I can't add
right now because of a dependency on mac80211, add a
reserved entry to keep the enum in place.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>