Enclose the rm9200 old clk registration in "#if defined(CONFIG_OLD_CLK_AT91)
 #endif"
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The platform specific <mach/timex.h> will be removed in a later patch.
So move its only still used symbol to a different header specific for
the only machine still using it. Also add a few explicit includes of
<mach/hardware.h> that are implicitly available through <mach/timex.h>.
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

This patch moves at91_pmc.h header from machine specific directory
(arch/arm/mach-at91/include/mach/at91_pmc.h) to clk include directory
(include/linux/clk/at91_pmc.h).
We need this to avoid reference to machine specific headers in clk
drivers.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Move non-dt selection to ioremap_registers init which is only called not
non-dt board.

So we can support sam9n12/sam9x5/sama5d3 too.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Using the platform driver model is a good way to separate the cpuidle specific
code from the low level pm code. It allows to remove the dependency between
these two components.

The platform_device is located in the pm code and a 'set' function has been
added to set the standby function from the AT91_SOC_START initialization
function. Each SoC with a cpuidle driver will set the standby function in the
platform_data field at init time. Then pm code will register the cpuidle
platform device.

The cpuidle driver will register the platform_driver and use the device's
platform_data as a standby callback in the idle path.

The at91_pm_enter function contains a { if then else } based on cpu_is_xx
similar to what was in cpuidle. This is considered dangerous when adding a new
SoC. Like the cpuidle driver, a standby ops is defined and assigned when the
SoC init function specifies what is its standby function and reused in the
at91_pm_enter's 'case' block.
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.

[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: NRobin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 4b68520dc0ec96153bc0d87bca5ffba508edfcf
ARM: at91: add AIC5 support

we allocate the at91_extern_irq.

This patch makes it static and stores the non-dt extern irq in the soc
structure. It is then possible to use a at91_get_extern_irq() function
to get the value for outside of the irq driver. It is useful for passing
its value to at91_aic_init().
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
[nicolas.ferre@atmel.com: rework commit message]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

New devices are no more prefixed with at91 so remove the at91 and _name
concatenation.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Add atmel-ssc for device tree support

Match "atmel,at91rm9200-ssc" for using pdc for data transfer
Match "atmel,at91sam9g45-ssc" for using dma for data transfer
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

as this is only used board old style board old mach code
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

Add platform device id to check whether the SSC controller support
pdc or dam for data transfer

If match "at91rm9200_ssc", which support pdc for data transfer
If match "at91sam9g45_ssc", which support dma for data transfer
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The i2c core driver will turn the platform device ID to busnum
When using platfrom device ID as -1, it means dynamically assigned
the busnum. When writing code, we need to make sure the busnum,
and call i2c_register_board_info(int busnum, ...) to register device
if using -1, we do not know the value of busnum

In order to solve this issue, set the platform device ID as a fix number
Here using 0 to match the busnum used in i2c_regsiter_board_info()
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>

Instead of check the pointer of the init function, check the new builtin bool
to known if the soc is enabled.

This is needed as with the switch to the pinctrl the init will be NULL on pure
DT SoC.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This driver has the following properties compared to the old driver:
1. Support for multiple interfaces.
2. Interrupt driven I/O as opposed to polling/busy waiting.
3. Support for _one_ repeated start (Sr) condition, which is enough
   for most real-world applications including all SMBus transfer types.
   (The hardware does not support issuing arbitrary Sr conditions on the
    bus.)

testing: SoC: at91sam9g45
	 - BQ20Z80 battery SMBus client.
	 - on a 2.6.38 kernel with several i2c clients (temp-sensor,
	   audio-codec, touchscreen-controller, w1-bridge, io-expanders)
Signed-off-by: NNikolaus Voss <n.voss@weinmann.de>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NHubert Feurstein <h.feurstein@gmail.com>
Tested-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: NNicolas Ferre <nicolas.ferre@atmel.com>

[wsa: squashed with the following patches from Ludovic to have some flaws
fixed:
        i2c: at91: use managed resources
        i2c: at91: add warning about transmission issues for some devices
        i2c: at91: use an id table for SoC dependent parameters
]
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The old driver used con_id clock entries. Convert to use dev_id
for clock lookup via standard method.
Signed-off-by: NNikolaus Voss <n.voss@weinmann.de>
Tested-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Enable sparse irq support for multisoc image. It involves to add the
NR_IRQS_LEGACY offset to static SoC irq number definitions since NR_IRQS_LEGACY
irq descs are allocated before AIC requests irq descs allocation.
Move NR_AIC_IRQS macro to a more appropiate place with the purpose to
remove mach/irqs.h later.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The AT91RM9200 Ethernet controller still has a fixed IO mapping.
So:
* Remove the fixed IO mapping and AT91_VA_BASE_EMAC definition.
* Pass the physical base-address via platform-resources to the driver.
* Convert at91_ether.c driver to perform an ioremap().
* Ethernet PHY detection needs to be performed during the driver
initialization process, it can no longer be done first.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

at91_set_serial_console is used to define the default console of linux.
This is already manage by the cmdline. And if the boot loader can not be
modified you can still set it by enabling the CONFIG_CMDLINE_EXTEND option.
And then the command-line arguments provided by the boot loader will be
appended to the default kernel command string.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Disintegrate asm/system.h for ARM.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NRyan Mallon <rmallon@gmail.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NRyan Mallon <rmallon@gmail.com>

... and hook it to arm_pm_idle.
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>

Rather than using a private function pointer, use the existing
arm_pm_restart function pointer instead.  We no longer need to enable
the I-cache in at91sam9_alt_reset() as the caches will now be on when
this function is called.

Update the function names to use the 'restart' terminology rather than
the 'reboot' terminology.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

this will simplify the switch to the DT and later to the platform_device
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

now sam9_smc_configure will take as first parameter is the SMC id
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

this will allow to ioremap the register of the PIT, PMC and others
and make the code soc independent
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NRyan Mallon <rmallon@gmail.com>

Remove the cpu_is_at91xxxx() macros in the ohci-at91 driver.
SoCs at91sam9261 and at91sam9g10 expect one additional clock: hck0.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>

instead of reading the registers everytime

the current implementation respect the following constrain:
 - allow 1 to n soc to be enabled
 - allow to have a virtual cpu type and subtype
 - always detect the cpu type and subtype and report it
 - detect if the soc support is enabled
 - prepare for sysfs export support
 - drop soc specific code via compiler when the soc not enabled
   (via cpu_is_xxx)

Today if we read the exid we will have the same value for 9g35 and 9m11
and we will need to check the cidr too

with the new implementation we just need to check the soc subtype

this will also allow to have specific virtual subtype for rm9200 which the
board will have to specify via at91rm9200_set_type(int) as we have no way to
detect it.

this implementation is inspired by the SH cpu detection support
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>

they are the same except the default priority
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>

On all at91 except rm9200 and x40 have the System Controller starts
at address 0xffffc000 and has a size of 16KiB.

On rm9200 it's start at 0xfffe4000 of 111KiB with non reserved data starting
at 0xfffff000

This patch removes the individual definitions of AT91_BASE_SYS and
replaces them with a common version at base 0xfffffc000 and size 16KiB
and map the same memory space
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>