Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 17 3月, 2014 7 次提交
  3. 14 3月, 2014 1 次提交
  5. 13 3月, 2014 3 次提交
    • G
      kvm: x86: ignore ioapic polarity · 100943c5
      由 Gabriel L. Somlo 提交于 
      Both QEMU and KVM have already accumulated a significant number of
optimizations based on the hard-coded assumption that ioapic polarity
will always use the ActiveHigh convention, where the logical and
physical states of level-triggered irq lines always match (i.e.,
active(asserted) == high == 1, inactive == low == 0). QEMU guests
are expected to follow directions given via ACPI and configure the
ioapic with polarity 0 (ActiveHigh). However, even when misbehaving
guests (e.g. OS X <= 10.9) set the ioapic polarity to 1 (ActiveLow),
QEMU will still use the ActiveHigh signaling convention when
interfacing with KVM.

This patch modifies KVM to completely ignore ioapic polarity as set by
the guest OS, enabling misbehaving guests to work alongside those which
comply with the ActiveHigh polarity specified by QEMU's ACPI tables.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NGabriel L. Somlo <somlo@cmu.edu>
[Move documentation to KVM_IRQ_LINE, add ia64. - Paolo]
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      100943c5
    • P
      KVM: PPC: Book3S HV: Fix register usage when loading/saving VRSAVE · e724f080
      由 Paul Mackerras 提交于 
      Commit 595e4f7e ("KVM: PPC: Book3S HV: Use load/store_fp_state
functions in HV guest entry/exit") changed the register usage in
kvmppc_save_fp() and kvmppc_load_fp() but omitted changing the
instructions that load and save VRSAVE.  The result is that the
VRSAVE value was loaded from a constant address, and saved to a
location past the end of the vcpu struct, causing host kernel
memory corruption and various kinds of host kernel crashes.

This fixes the problem by using register r31, which contains the
vcpu pointer, instead of r3 and r4.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      e724f080
    • P
      KVM: PPC: Book3S HV: Remove bogus duplicate code · a5b0ccb0
      由 Paul Mackerras 提交于 
      Commit 7b490411 ("KVM: PPC: Book3S HV: Add new state for
transactional memory") incorrectly added some duplicate code to the
guest exit path because I didn't manage to clean up after a rebase
correctly.  This removes the extraneous material.  The presence of
this extraneous code causes host crashes whenever a guest is run.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      a5b0ccb0
  7. 11 3月, 2014 11 次提交
    • P
      KVM: svm: Allow the guest to run with dirty debug registers · facb0139
      由 Paolo Bonzini 提交于 
      When not running in guest-debug mode (i.e. the guest controls the debug
registers, having to take an exit for each DR access is a waste of time.
If the guest gets into a state where each context switch causes DR to be
saved and restored, this can take away as much as 40% of the execution
time from the guest.

If the guest is running with vcpu->arch.db == vcpu->arch.eff_db, we
can let it write freely to the debug registers and reload them on the
next exit.  We still need to exit on the first access, so that the
KVM_DEBUGREG_WONT_EXIT flag is set in switch_db_regs; after that, further
accesses to the debug registers will not cause a vmexit.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      facb0139
    • P
      KVM: svm: set/clear all DR intercepts in one swoop · 5315c716
      由 Paolo Bonzini 提交于 
      Unlike other intercepts, debug register intercepts will be modified
in hot paths if the guest OS is bad or otherwise gets tricked into
doing so.

Avoid calling recalc_intercepts 16 times for debug registers.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      5315c716
    • P
      KVM: nVMX: Allow nested guests to run with dirty debug registers · d16c293e
      由 Paolo Bonzini 提交于 
      When preparing the VMCS02, the CPU-based execution controls is computed
by vmx_exec_control.  Turn off DR access exits there, too, if the
KVM_DEBUGREG_WONT_EXIT bit is set in switch_db_regs.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      d16c293e
    • P
      KVM: vmx: Allow the guest to run with dirty debug registers · 81908bf4
      由 Paolo Bonzini 提交于 
      When not running in guest-debug mode (i.e. the guest controls the debug
registers, having to take an exit for each DR access is a waste of time.
If the guest gets into a state where each context switch causes DR to be
saved and restored, this can take away as much as 40% of the execution
time from the guest.

If the guest is running with vcpu->arch.db == vcpu->arch.eff_db, we
can let it write freely to the debug registers and reload them on the
next exit.  We still need to exit on the first access, so that the
KVM_DEBUGREG_WONT_EXIT flag is set in switch_db_regs; after that, further
accesses to the debug registers will not cause a vmexit.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      81908bf4
    • P
      KVM: x86: Allow the guest to run with dirty debug registers · c77fb5fe
      由 Paolo Bonzini 提交于 
      When not running in guest-debug mode, the guest controls the debug
registers and having to take an exit for each DR access is a waste
of time.  If the guest gets into a state where each context switch
causes DR to be saved and restored, this can take away as much as 40%
of the execution time from the guest.

After this patch, VMX- and SVM-specific code can set a flag in
switch_db_regs, telling vcpu_enter_guest that on the next exit the debug
registers might be dirty and need to be reloaded (syncing will be taken
care of by a new callback in kvm_x86_ops).  This flag can be set on the
first access to a debug registers, so that multiple accesses to the
debug registers only cause one vmexit.

Note that since the guest will be able to read debug registers and
enable breakpoints in DR7, we need to ensure that they are synchronized
on entry to the guest---including DR6 that was not synced before.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      c77fb5fe
    • P
      KVM: x86: change vcpu->arch.switch_db_regs to a bit mask · 360b948d
      由 Paolo Bonzini 提交于 
      The next patch will add another bit that we can test with the
same "if".
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      360b948d
    • P
      KVM: vmx: we do rely on loading DR7 on entry · c845f9c6
      由 Paolo Bonzini 提交于 
      Currently, this works even if the bit is not in "min", because the bit is always
set in MSR_IA32_VMX_ENTRY_CTLS.  Mention it for the sake of documentation, and
to avoid surprises if we later switch to MSR_IA32_VMX_TRUE_ENTRY_CTLS.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      c845f9c6
    • J
      KVM: x86: Remove return code from enable_irq/nmi_window · c9a7953f
      由 Jan Kiszka 提交于 
      It's no longer possible to enter enable_irq_window in guest mode when
L1 intercepts external interrupts and we are entering L2. This is now
caught in vcpu_enter_guest. So we can remove the check from the VMX
version of enable_irq_window, thus the need to return an error code from
both enable_irq_window and enable_nmi_window.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      c9a7953f
    • J
      KVM: nVMX: Do not inject NMI vmexits when L2 has a pending interrupt · 220c5672
      由 Jan Kiszka 提交于 
      According to SDM 27.2.3, IDT vectoring information will not be valid on
vmexits caused by external NMIs. So we have to avoid creating such
scenarios by delaying EXIT_REASON_EXCEPTION_NMI injection as long as we
have a pending interrupt because that one would be migrated to L1's IDT
vectoring info on nested exit.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      220c5672
    • J
      KVM: nVMX: Fully emulate preemption timer · f4124500
      由 Jan Kiszka 提交于 
      We cannot rely on the hardware-provided preemption timer support because
we are holding L2 in HLT outside non-root mode. Furthermore, emulating
the preemption will resolve tick rate errata on older Intel CPUs.

The emulation is based on hrtimer which is started on L2 entry, stopped
on L2 exit and evaluated via the new check_nested_events hook. As we no
longer rely on hardware features, we can enable both the preemption
timer support and value saving unconditionally.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      f4124500
    • J
      KVM: nVMX: Rework interception of IRQs and NMIs · b6b8a145
      由 Jan Kiszka 提交于 
      Move the check for leaving L2 on pending and intercepted IRQs or NMIs
from the *_allowed handler into a dedicated callback. Invoke this
callback at the relevant points before KVM checks if IRQs/NMIs can be
injected. The callback has the task to switch from L2 to L1 if needed
and inject the proper vmexit events.

The rework fixes L2 wakeups from HLT and provides the foundation for
preemption timer emulation.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      b6b8a145
  9. 06 3月, 2014 2 次提交
  11. 04 3月, 2014 12 次提交
  13. 03 3月, 2014 4 次提交