Use ata_wait_after_reset() to poll for link recovery after a reset.
This combined with sas_ha->eh_mutex prevents expander rediscovery from
probing phys in an intermediate state.  Local discovery does not have a
mechanism to filter link status changes during this timeout, so it
remains the responsibility of lldds to prevent premature port teardown.
Although once all lldd's support ->lldd_ata_check_ready() that could be
used as a gate to local port teardown.

The signature fis is re-transmitted when the link comes back so we
should be revalidating the ata device class, but that is left to a future
patch.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Once sas_ata_hard_reset() starts honoring the 'deadline' parameter a
pathological configuration could take 25 seconds per ata device
(serialized) to recover.  Run per-port recoveries in parallel.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

SAS does not tag SMP requests, and at least one lldd (isci) does not permit
more than one in-flight request at a time.

[jejb: fix sas_init_dev tab issues while we're at it]
Signed-off-by: NJeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

In the case of an explicit sas_phy_enable call to disable a phy,
the LLDD provides the calls to sas_phy_disconnected and the
PHYE_LOSS_OF_SIGNAL event.

NOTE: This assumes that the lldd(s) generate the notification, which
appears to be the case, but only verfied on isci.
Signed-off-by: NJeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Execute the link-reset triggered by sas_phy_enable via
transport_sas_phy_reset so that it can be managed by libata.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Link resets leave ata affiliations intact, so arrange for libsas to make
an effort to avoid dropping the device due to a slow-to-recover link.
Towards this end carry out reset in the host workqueue so that it can
check for ata devices and kick the reset request to libata.  Hard
resets, in contrast, bypass libata since they are meant for associating
an ata device with another initiator in the domain (tears down
affiliations).

Need to add a new transport_sas_phy_reset() since the current
sas_phy_reset() is a utility function to libsas lldds.  They are not
prepared for it to loop back into eh.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Extend the sas transport class to allow transport users to attach extra
data to a sas_phy (->hostdata).  Use this area in libsas to move resets
to workq context in preparation for scheduling ata device resets through
libata-eh.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Since sata devices can take several seconds to recover the link on reset
the 0.5 seconds that libsas currently waits may not be enough.  Instead
if we are rediscovering a phy that was previously attached to a sata
device let libata handle any resets to encourage the device to transmit
the initial fis.

Once sas_ata_hard_reset() and lldds learn how to honor 'deadline' libsas
should stop encountering phys in an intermediate state, until then this
will loop until the fis is transmitted or ->attached_sas_addr gets
cleared, but in the more likely initial discovery case we keep existing
behavior.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

lldds use the SAS_TASK_NEED_DEV_RESET interface to request that eh
perform a reset.  In the sata device case defer the commands that
triggered the reset to libata-eh context so it can perform its pre and
post reset management.

In the sas_ata_post_internal() case the reset request is falling on deaf
ears as the sas_task is immediately destroyed without any reset action.
Since it is currently a nop, and likely superfluous given the conversion
to new-style libata-eh, just drop the request.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

libsas-eh if it successfully aborts an ata command will hide the timeout
condition (AC_ERR_TIMEOUT) from libata.  The command likely completes
with the all-zero task->task_status it started with.  Instead, interpret
a TMF_RESP_FUNC_COMPLETE as the end of the sas_task but keep the scmd
around for libata-eh to handle.
Tested-by: NAndrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Until we have told the lldd to forget a task a timed out operation can
return from the hardware at any time.  Since completion frees the task
we need to make sure that no tasks run their normal completion handler
once eh has decided to manage the task.  Similar to
ata_scsi_cmd_error_handler() freeze completions to let eh judge the
outcome of the race.

Task collector mode is problematic because it presents a situation where
a task can be timed out and aborted before the lldd has even seen it.
For this case we need to guarantee that a task that an lldd has been
told to forget does not get queued after the lldd says "never seen it".
With sas_scsi_timed_out we achieve this with the ->task_queue_flush
mutex, rather than adding more time.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

We invoke task->task_done() to free the task in the eh case, but at this
point we are prepared for scsi_eh_flush_done_q() to finish off the scmd.

Introduce sas_end_task() to capture the final response status from the
lldd and free the task.

Also take the opportunity to kill this warning.
drivers/scsi/libsas/sas_scsi_host.c: In function ‘sas_end_task’:
drivers/scsi/libsas/sas_scsi_host.c:102:3: warning: case value ‘2’ not in enumerated type ‘enum exec_status’ [-Wswitch]
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Since sas_ata does not implement ->freeze(), completions for scmds and
internal commands can still arrive concurrent with
ata_scsi_cmd_error_handler() and sas_ata_post_internal() respectively.
By the time either of those is called libata has committed to completing
the qc, and the ATA_PFLAG_FROZEN flag tells sas_ata_task_done() it has
lost the race.

In the sas_ata_post_internal() case we take on the additional
responsibility of freeing the sas_task to close the race with
sas_ata_task_done() freeing the the task while sas_ata_post_internal()
is in the process of invoking ->lldd_abort_task().
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Prior to the conversion to the new-style libata-eh sas_ata_task_done()
may have been the last opportunity to clean up the scmd, but now
libata-eh explicitly handles this case.  It also races against sas-eh.
If a lldd completes a task after SAS_TASK_STATE_ABORTED is set it could
trigger a spurious decrement of shost->host_failed.  Current lldds have
the band-aid of checking SAS_TASK_STATE_ABORTED before calling
->task_done(), but better to just let the scmds escalate to libata for
race free cleanup.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

sas_discover_sata() notifies lldds of sata devices twice.  Once to allow
the 'identify' to be sent, and a second time to allow aic94xx (the only
libsas driver that cares about sata_dev.identify) to setup NCQ
parameters before the device becomes known to the midlayer.  Replace
this double notification and intervening 'identify' with an explicit
->lldd_ata_set_dmamode notification.  With this change all ata internal
commands are issued by libata, so we no longer need sas_issue_ata_cmd().

The data from the identify command only needs to be cached in one
location so ata_device.id replaces domain_device.sata_dev.identify.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

libata error handling provides for a timeout for link recovery.  libsas
must not rescan for previously known devices in this interval otherwise
it may remove a device that is simply waiting for its link to recover.
Let libata-eh make the determination of when the link is stable and
prevent libsas (host workqueue) from taking action while this
determination is pending.

Using a mutex (ha->disco_mutex) to flush and disable revalidation while
eh is running requires any discovery action that may block on eh be
moved to its own context outside the lock.  Probing ATA devices
explicitly waits on ata-eh and the cache-flush-io issued during device
removal may also pend awaiting eh completion.  Essentially any rphy
add/remove activity needs to run outside the lock.

This adds two new cleanup states for sas_unregister_domain_devices()
'allocated-but-not-probed', and 'flagged-for-destruction'.  In the
'allocated-but-not-probed' state  dev->rphy points to a rphy that is
known to have not been through a sas_rphy_add() event.  At domain
teardown check if this device is still pending probe and cleanup
accordingly.  Similarly if a device has already been queued for removal
then sas_unregister_domain_devices has nothing to do.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

In preparation for adding tracking of another device state "destroy".
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Each libsas driver (mvsas, pm8001, and isci) has invented a different
method for managing the ap->lock.  The lock is held by the ata
->queuecommand() path.  mvsas drops it prior to acquiring any internal
locks which allows it to hold its internal lock across calls to
task->task_done().  This capability is important as it is the only way
the driver can flush task->task_done() instances to guarantee that it no
longer has any in-flight references to a domain_device at
->lldd_dev_gone() time.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When an lldd invokes ->notify_port_event() it can trigger a chain of libsas
events to:

  1/ form the port and find the direct attached device

  2/ if the attached device is an expander perform domain discovery

A call to flush_workqueue() will only flush the initial port formation work.
Currently libsas users need to call scsi_flush_work() up to the max depth of
chain (which will grow from 2 to 3 when ata discovery is moved to its own
discovery event).  Instead of open coding multiple calls switch to use
drain_workqueue() to flush sas work.

drain_workqueue() does not handle new work submitted during the drain so
libsas needs a bit of infrastructure to hold off unchained work submissions
while a drain is in flight.  A lldd ->notify() event is considered 'unchained'
while a sas_discover_event() is 'chained'.  As Tejun notes:

  "For now, I think it would be best to add private wrapper in libsas to
   support deferring unchained work items while draining."
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

In preparation for adding new states (SAS_HA_DRAINING, SAS_HA_FROZEN),
convert ha->state into a set of flags.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The locks only served to make sure the pending event bitmask was updated
consistently.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

These are never freed in the nominal path.  A domain_device has a
different lifetime than a sas_rphy we need a dev->rphy independent way
of identifying sata devices.
Reviewed-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Arrange for the deallocation of a struct domain_device object when it no
longer has:
1/ any children
2/ references by any scsi_targets
3/ references by a lldd

The comment about domain_device lifetime in
Documentation/scsi/libsas.txt is stale as it appears mainline never had
a version of a struct domain_device that was registered as a kobject.
We now manage domain_device reference counts on behalf of external
agents.
Reviewed-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Per commit 3e4ec344 "libata: kill ATA_FLAG_DISABLED" needing to set
ATA_DEV_NONE is a holdover from before libsas converted to the
"new-style" ata-eh.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit 1e34c838 "[SCSI] libsas: remove spurious sata control register
read/write" removed the routines to fake the presence of the sata
control registers, now remove the unused data structure fields to kill
any remaining confusion.
Acked-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

We have experienced several devices which fail in a fashion we do not
currently handle gracefully in SCSI. After a failure these devices will
respond to the SCSI primary command set (INQUIRY, TEST UNIT READY, etc.)
but any command accessing the storage medium will time out.

The following patch adds an callback that can be used by upper level
drivers to inspect the results of an error handling command. This in
turn has been used to implement additional checking in the SCSI disk
driver.

If a medium access command fails twice but TEST UNIT READY succeeds both
times in the subsequent error handling we will offline the device. The
maximum number of failed commands required to take a device offline can
be tweaked in sysfs.

Also add a new error flag to scsi_debug which allows this scenario to be
easily reproduced.

[jejb: fix up integer parsing to use kstrtouint]
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The virtio-scsi HBA is the basis of an alternative storage stack
for QEMU-based virtual machines (including KVM).  Compared to
virtio-blk it is more scalable, because it supports many LUNs
on a single PCI slot), more powerful (it more easily supports
passthrough of host devices to the guest) and more easily
extensible (new SCSI features implemented by QEMU should not
require updating the driver in the guest).
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Some other older controllers also do have problems to perform a kdump.
Adding controllers to this list means that the driver will signal
this non-ability via a resettable flag correctly.
The unsupported list was created after a consultation with HP.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: NMike Miller <mike.miller@hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Permanent target failures are non-retryable and should be classified as
TARGET_ERROR; otherwise dm-multipath will retry an IO request that will
always fail at the target.

A SCSI command that fails with ILLEGAL_REQUEST sense and Additional
sense 0x20, 0x21, 0x24 or 0x26 represents a permanent TARGET_ERROR.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The provisioning_mode parameter in sysfs did not get updated in the
SD_LBP_DISABLE case. Make sure the provisioning mode is always set
correctly.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The error reported up the stack for a discard failure did not clearly
indicate that the command was processed and subsequently failed by the
target device.

Return -EREMOTEIO so multipathing does not classify this condition as a
path failure.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The __get_free_pages can fail, so the return value should be checked.
Spotted thanks to Stanislaw.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Added ping support for network connection diagnostics.
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Added ping support for iscsi adapter, application can use this
interface for diagnostic network connection.
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Added support to post kernel host event to application using
netlink interface.
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Added support to post kernel host event to application using
netlink interface.
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

On ROM lock acquiring timeout failure, driver spews lot of warning
messages in a for loop, remove the unwanted warning message to reduce
kernel messages clutter.
Signed-off-by: NLalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>