This is needed for devices with DRX-K and xc5000.

Tested with a HVR 930C hardware.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Annex C support were broken with the previous implementation,
as, at xc5000 and tda18271c2dd, it were choosing the wrong bandwidth
for some symbol rates.

At DRX-J, it were always selecting Annex A, even having Annex C
support coded there.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Brazil uses 6MHz-spaced channels. So, the nyquist filter for
DVB-C should be different, otherwise, inter-channel interference
may badly affect the device, and signal may not be properly decoded.

On my tests here, without this patch, sometimes channels are seen,
but, most of the time, PID filter returns with timeout.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add one more radio input, usefull for tm6010
Add control output amplitude.
Add set_config function for configure tuner when TV card hasn't dvb part.
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Making static data const avoids allocation of additional r/w memory and
reduces initialisation time.  It also provides some additional opportunities
for compiler optimisations.
Signed-off-by: NLawrence Rust <lvr@softsystem.co.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/common/tuners/xc5000.c: In function ‘xc_write_reg’:
drivers/media/common/tuners/xc5000.c:298: warning: passing argument 3 of ‘xc5000_readreg’ from incompatible pointer type
drivers/media/common/tuners/xc5000.c:235: note: expected ‘u16 *’ but argument is of type ‘u8 *’
drivers/media/common/tuners/xc5000.c: At top level:
drivers/media/common/tuners/xc5000.c:223: warning: ‘xc_read_i2c_data’ defined but not used
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rework xc_write_reg function for correct read register of the xc5000.
It is very useful for tm6000.

Tested for tm6000 and for saa7134 works well.
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Xc5000 tuning attempts shouldn't return zero in the case where the firmware
did not load successfully.

Thanks to Michael Krufky for pointing out this issue.

Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove hard-coded definition of the xc5000 FM radio input, making it a
parameter passed in when doing the attach call.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add FM radio for the xc5000 silicon tuner chip.
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add copyright line for xc5000.c.

Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of polling at 100ms intervals for register writes, poll at 5ms
intervals.  This is consistent with the xc5000 specification, and improves
tuning time by up to 500 ms on devices that such as the au0828 which do not
properly implement i2c clock stretching (since the five register writes that
occur for a tuning request often do not complete immediately but do complete
far before 100ms has gone by).

The net amount of time we wait before timing out is unchanged (500ms).
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds XC5000 supports for DVB-T 6MHz and 8MHz bandwidth.
Signed-off-by: NDavid T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Xceive has graciously allowed us to now freely redistribute the xc5000
firmware, which eliminates the need for users to manually extract the blob
from the Hauppauge driver.

Thanks to Brian Mathews <bmathews@xceive.com> for providing this code
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Provide for the ability for a user to disable putting the tuner to sleep, in
case he doesn't want to incur the cost of reloading the firmware when starting
up his/her application.  The module options are intentionally identical to
xc3028.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make it a little more obvious in the dmesg output what is going on during
firmware upload.  This is more important for boards like the HVR-950q that
take nearly seven seconds to do the upload.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Starting in firmware version 1.1.44, Xceive recommends using the FINERFREQ for
all normal tuning (the doc indicates reg 0x03 should only be used for fast
scanning for channel lock)
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Expose the firmware build number along with the other version info
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Xceive got rid of the XREG_POWER_DOWN register in later firmware revisions.
Their technical support informed me that the correct way to put the tuner
to sleep is to pull the reset pin (but don't reload the firmware).
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This switches to a new version of the xc5000 firmware, extracted from the
latest Hauppauge driver.  It includes the support for the XREG_BUSY register
(a lack of which was causing tuning to take 3200ms instead of around 300ms).
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Don't sleep for 400ms polling the tuner's lock if in digital mode (since the
xc5000 lock status registers appear to only be reliable in analog mode)
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Bring back the code that puts the xc5000 to sleep.  For the Pinnacle 801e
this results in power consumption at idle dropping from 325ma to 124ma.

If there are *actually* any devices that don't work in this configuration,
they should set dvb_frontend.ops.tuner_ops.sleep to NULL (per mkrufky's
suggestion)

Also, had to make sure we were making sure the firmware was loaded in the
digital version of set_params, or else we end up get i2c errors if the
device is asleep
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make return value checking for calls to i2c routines explicit.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Cleanup the i2c write routine, getting rid of a passthrough function with only
one caller
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch centralizes the i2c read functions, and eliminates pass-through
function only called by one caller.

Make reading of xc5000 registers an atomic i2c transaction in case we're on a
multi-master bus.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Properly handle tuner reset failures (before it was always returning success)
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the physical device rather than the i2c adapter as the reference
device when loading firmwares. This will prevent the sysfs name
collision with i2c-dev that has been reported many times.

I may have missed other drivers which need the same fix.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The xc5000 driver has a bug where the IF is always set to whatever the first
caller to dvb_attach() provides.  This fails when the device requires an IF
other than 5380 and the analog driver is loaded first through tuner-core
(which always supplies the hard-coded value of 5380).

Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSrinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The init_fw option was broken for the HVR-950q because we would call the reset
callback inside of dvb_attach() and the callback had not been setup yet.

Michael Krufky (who added the init_fw feature) says it's no longer required,
so just remove the option completely.

Thanks to user Zzeiss from #linuxtv chat for reporting the issue and
Michael Krufky <mkrufky@linuxtv.org> for proposing the fix.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

xc5000: Checkpatch compliance
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Dont pass devptr in xc5000_attach, dont store it in xc5000_priv.
This pointer is passed into the tuner_callback function, which always
expects a pointer to fe->dvb->priv or i2c_adapter->algo_data.

This prevents future possible bugs in new drivers, such as using a "devptr"
other that the standard fe->dvb->priv in a DVB driver.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Prevent an OOPS if xc5000_attach was called by tuner.ko before being called by
the DVB adapter driver. The OOPS occurs when a digital tune request is made
after tuner.ko is unloaded.

When tuner.ko is unloaded, it takes the xc5000_config structure with it.

Rather than storing a pointer to the xc5000_config structure, just store the
if_khz and tuner_callback inside the xc5000_priv internal state structure.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert xc5000 to use the hybrid_tuner_request_state and
hybrid_tuner_release_state macros to manage state sharing between
hybrid tuner instances.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

move struct xc5000_priv into xc5000.c and delete xc5000_priv.h
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I need this so I can better isolate my linux email from my
corporate email.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The xc5000 firmware download process can be slow on certain devices.

Add a module option, "init_fw" to perform the firmware download during
xc5000_attach(), which would get the firmware download over with well
before any tune request is made.

When this option is enabled, it will reduce the time it takes to get a
signal lock during the first tune after driver load, but will add a few
seconds to the driver initialization.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>