mac80211 already masks the HT sta capabilities based on hardware support
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace calls that read this capability with accesses to ath9k_hw's
regulatory data.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The non-irqsafe aggregation start/stop done
callbacks are currently only used by ath9k_htc,
and can cause callbacks into the driver again.
This might lead to locking issues, which will
only get worse as we modify locking. To avoid
trouble, remove the non-irqsafe versions and
change ath9k_htc to use those instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR7010 is dual-band. Setup the channels and rateset
for 5GHz band.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rate information on the target has to be updated
for 2-stream devices, along with the correct chainmask.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sta_add/sta_remove are the callbacks that can sleep.
Use them instead of sta_notify.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes beacon distribution in IBSS mode
by configuring the hardware beacon queue properly.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The MIB counters used by ANI have to be disabled
on the host because the FW doesn't do it on the target side.
Also, flush the receive buffers before initializing
RX on the target.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The monitor interface instance on the target has
to be removed before setting it to FULLSLEEP.
Handle this properly.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ps_idle is protected by the htc_pm_lock mutex.
Use it to protect the variable.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to cancel the PS work when disassociation
happens. The work handlers are cancelled in the stop()
callback.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Disable the radio only when mac80211 indicates it,
through the IEEE80211_CONF_CHANGE_IDLE flag.
Not handling this properly will result in multiple
calls to radio_disable() even though the radio is
already idle.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The HW has to be awake when registers are accessed.
Ensure this is so by using the PS wrappers at
appropriate places.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch revamps IDLE power save handling in the driver.
Two separate functions (radio enable/disable) are introduced,
because the semantics of radio handling is just not the same
as the start()/stop() callbacks. For example, the HW must not
be disabled, instead, the PHY has to be disabled in radio_disable().
Also, the HW has to be reset properly in radio enable/disable and
certain registers have to be programmed only once, in the
start() callback.

The radio_enable() routine doesn't need the PS wrappers since
we set the HW power mode to AWAKE anyway before calling it.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use BSS_CHANGED_HT to handle HT parameter changes.
The rate information on the target has to be updated
to handle changes in HT configuration.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes a large chunk of code dealing
with rate management within the driver and simplifying
things by removing the hacky method of calculating
HT changes. A subsequent patch would fix this by
just using BSS_CHANGED_HT from mac80211.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since ->sta_notify() can sleep, protect
the callback with a mutex.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I changed "> ATH9K_HTC_MAX_TID" to ">= ATH9K_HTC_MAX_TID" to avoid a
potential overflow.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a stray null dereference.  We initialize "ista" properly later on.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Switch LED off/on when handling CONF_CHANGE_IDLE.
Not doing this would leave the radio LED on even
though the chip would be in full sleep mode.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current way of managing beaconing in ad-hoc
mode has a subtle race - the beacon obtained from mac80211
is freed in the SWBA handler rather than the TX
completion routine. But transmission of beacons goes
through the normal SKB queue maintained in hif_usb,
leading to a situation where __skb_dequeue() in the TX
completion handler goes kaput.

Fix this by simply getting a beacon from mac80211 for
every SWBA and free it in its completion routine.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bunch of endian issues that
were exposed by sparse. It's a miracle that the driver
worked at all till now.

The Lord be praised.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no point in trying to set the LED pin
when the module is being unloaded. The target
would be reset anyway.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up beacon configuration,
removing a redundant interface type check
and updating beacon interval in the correct place.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stop/restart TX queues when the internal SKB
queue is full. This helps handle TX better
under heavy load.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Accessing the sta pointer in TX completion without
approprate RCU protection is wrong. Fix this.

Also, RCU protection is needed when the station's
aggregation state is updated. Handle this properly.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The calculation of RX filter is fairly different
between ath9k and ath9k_htc, trying to make this
common between the two drivers would result in code churn.

While at it, remove the handling of PSPOLL filter,
it can be added when(if) AP support is added to ath9k_htc.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Features:

 * Station mode
 * IBSS mode
 * Monitor mode
 * Legacy support
 * HT support
 * TX/RX 11n Aggregation
 * HW encryption
 * LED
 * Suspend/Resume

For more information: http://wireless.kernel.org/en/users/Drivers/ath9k_htcSigned-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>