Freezeable workqueue makes sure that adapter work items (device insertions
and removals) would be handled after the system is fully resumed. Previously
this was achieved by explicit freezing of the kthread.
Signed-off-by: NAlex Dubov <oakad@yahoo.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Remove code duplicating the kernel functionality and clean up data
structures involved in driver matching.
Signed-off-by: NAlex Dubov <oakad@yahoo.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NAlex Dubov <oakad@yahoo.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Instead of passing transformed value of adapter interrupt status to
socket drivers, implement two separate callbacks - one for card events
and another for dma events.
Signed-off-by: NAlex Dubov <oakad@yahoo.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Avoid giving the user the possibility to shoot his own foot and let
the meye driver enable/disable the camera wisely (PCI_ID based).
Signed-off-by: NMattia Dongili <malattia@linux.it>
Signed-off-by: NLen Brown <len.brown@intel.com>

Copy and rename (for easier co-existence) the MEYE-wise exported interface.
Signed-off-by: NMattia Dongili <malattia@linux.it>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add the exported sony_pic_camera_command() function to make the MEYE
driver happy.
Signed-off-by: NMattia Dongili <malattia@linux.it>
Signed-off-by: NLen Brown <len.brown@intel.com>

Get the IO resources list in sony-laptop in the same order as listed
in sonypi and make sonypi check if one of those is already busy.
The sonypi check can be disabled by a module parameter in case the user
thinks we are plainly wrong (check_ioport=0).
Signed-off-by: NMattia Dongili <malattia@linux.it>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some SZ Vaios have a gsm built-in modem. Allow powering on/off this device.
Thanks to Joshua Wise for the base code.
Signed-off-by: NMattia Dongili <malattia@linux.it>
Signed-off-by: NLen Brown <len.brown@intel.com>

Better avoid having ioport commands mixing and global variables reading/writing.
Signed-off-by: NMattia Dongili <malattia@linux.it>
Signed-off-by: NLen Brown <len.brown@intel.com>

Use a parameter to enable/disable motion eye camera (for C1VE/C1VN models)
controls and avoid entering an infinite loop if the camera is not present
and the HW doesn't answer as we expect on io commands.
Signed-off-by: NMattia Dongili <malattia@linux.it>
Signed-off-by: NLen Brown <len.brown@intel.com>

This patch makes the needlessly global fan_mutex static.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add support to sysfs to the wan and bluetooth subdrivers.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add the hotkey sysfs support.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

The dock sub-driver has split-personality (two subdrivers), and it was
doing some unoptimal things on init because of that.  Fix it so that the
second half of it will only init when necessary, and only if the first half
initialized sucessfully in the first place.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some issues with the dock subdriver proved that a slightly improved
debugging setup for ACPI notifiers and handler helpers would be useful.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Currently, all fan control operations return ENXIO if unsupported
operations are requested, but return EINVAL if invalid fan modes are
requested on a given ThinkPad.

This is not strictly correct for sysfs, so map ENXIO to EINVAL in the sysfs
attribute store handlers, as we do benefit from the ENXIO in other parts of
the driver code.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

The fan control watchdog was being called in one place even when the fan
control operation had failed.  Fix it.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Do not enable/rearm the fan control safety watchdog if we would not be able
to do anything to the fan anyway.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Len Brown considers that an active by default fan control interface in
laptops may be too close to giving users enough rope.  There is a good
chance he is quite correct on this, especially if someone decides to use
that interface in applets and users are not aware of its risks.

This patch adds a master switch to thinkpad-acpi that enables or disables
the entire fan-control feature as a module parameter: "fan_control".  It
defaults to disabled.  Set it to non-zero to enable fan control.

Also, the patch removes the expermiental status from fan control, since it
is stable enough to not be called experimental, and the master switch makes
it safe enough to do so.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Update the brightness sysfs interface (done through the backlight class) to
be in line with the rest of the thinkpad-acpi driver.

This renames the incorrect, un-obvious, and clash-prone name of "ibm" for
the backlight device to a much more fitting and descriptive
"thinkpad_screen".  This is something I wanted to do for quite a while...
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add sysfs attributes to send ThinkPad CMOS commands.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

The Linux ThinkPad community is not positive that all ThinkPads that do
HFSP EC fan control do implement full-speed and auto modes, some of the
earlier ones supporting HFSP might not.

If the EC ignores the AUTO or FULL-SPEED bits, it will pay attention to the
lower three bits that set the fan level.  And as thinkpad-acpi was leaving
these set to zero, it would stop(!) the fan, which is Not A Good Thing.

So, as a safety net, we now make sure to also set the fan level part of the
HFSP register to speed 7 for full-speed, and a minimum of speed 4 for auto
mode.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Export sysfs attributes to monitor and control the internal thinkpad fan
(some thinkpads have more than one fan, but thinkpad-acpi doesn't support
the second fan yet).  The sysfs interface follows the hwmon design guide
for fan devices.

Also, fix some stray "thermal" files in the fan procfs description that
have been there forever, and officially support "full-speed" as the name
for the PWM-disabled state of the fan controller to keep it in line with
the hwmon interface.  It is much better a name for that mode than the
unobvious "disengaged" anyway.  Change the procfs interface to also accept
full-speed as a fan level, but still report it as disengaged for backwards
compatibility.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Export thinkpad thermal sensors to sysfs, following the hwmon
specification for thermal monitoring sensors.

ThinkPad thermal monitoring is done by the EC.  Sensors can show up or
disappear at runtime when they are inside hotswappable hardware, such as
batteries.  Sensors that are not available return -ENXIO when accessed.

Up to 16 thermal sensors are supported on new firmware (but nobody has
reported a ThinkPad with more than 12 sensors so far), and 8 sensors are
supported on older firmware.  Thermal sensor mapping is model-specific.
Precision varies, it is 1 degree Celcius on new ThinkPads, but higher on
some older models.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add proper mutex locking to some data structures access subject to races
due to concurrent access of driver functions on the hotkey and fan
subdrivers.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add infrastructure to deal with sysfs attributes and grouping, and helpers
for common sysfs parsing.  Switch driver attributes to use them.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add the sysfs attributes for the platform driver.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Register thinkpad-acpi platform driver and platform device for the device
model.  Also register the platform device with the hwmon class.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Improve some of the fan watchdog error messages to be a little more
helpful.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Clean-up the thermal subdriver for sysfs conversion.  Make thermal_get_*
reentrancy-safe while at it, and add the missing thermal_read_mode variable
to the header file.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some ThinkPad CMOS commands subdriver cleanups, and also rename/promote
cmos_eval to a ACPI helper function, as it is used by many other
subdrivers.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Cleanup video subdriver for sysfs conversion, and properly check
result status of acpi_evalf.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Prepare bluetooth and wan driver code to be more easily hooked into sysfs
helpers, by separating the procfs logic from the device attribute handling.

These changes also remove the entries from procfs on notebooks without the
bluetooth/wan hardware installed.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Cleanup hotkey subdriver code.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Mark acpi_evalf and friends __must_check.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Prepare the thinkpad-acpi driver for the conversion to the device
model, by renaming variables and doing other glue work that shall
make the later patches much cleaner.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Use a bitfield to hold boolean module-wide flags, to conserve some memory.
It is easy and it is clean, so we do it just for the heck of it even if it
saves very little space.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Save some memory by using bitfields to hold boolean flags for the
subdrivers.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Improve the detection of ThinkPads, so as to reduce the chances of false
positives.

Since this could potentially add false negatives on the very old models,
add a module parameter to force the detection of a thinkpad.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>