The time to suspend a single codec may be several hundreds of ms. When runtime
power saving is disabled, driver suspend time can be long especially when there
are more than one codec on the bus.

To reduce driver suspend time, this patch creates a work queue for the bus, and
suspends the codecs in parallel if there are multiple codecs on the bus.

[fixed cosmetic issues by tiwai]
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

According to Mengdong, we shouldn't enable runtime PM when a codec
doesn't support EPSS, based on the experiences on Windows.
We have already this check in HDMI codec drivers, but now apply it in
general in hda_codec.c.

Credit goes to Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Now we fixed the long-standing bugs of runtime PM, let's enable
Panther Point again.  The runtime PM was disabled in the HDMI codec
driver due to the S3 issue, and this should have been fixed now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

No functional change.

- codec->pm_down_notified flag is renamed to codec->pm_up_notified
  flag (and takes the reversed meaning), which is managed solely in
  hda_call_pm_notify() now.

- The explicit call of hda_call_pm_notify() is moved into
  hda_keep_power_on().

- Removed a redundant call of hda_call_pm_notify() in
  snd_hda_power_up(), as it's called in hda_call_codec_resume()
  anyway.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If a codec contains only the digital outputs, it's very likely a
HDMI/DP codec, which isn't supported by the generic parser but via
HDMI codec parser code.  Detect such a case and bind with the proper
parser object if available.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Drop the hard dependency on the generic parser code and load / unload
the generic parser code dynamically if built as a module.  This allows
us to avoid the generic parser if only HDMI/DP codecs are found.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use bus->power_keep_link_on instead.  The controller shouldn't go to
D3 when the link isn't reset, so essentially avoiding the link reset
means avoiding the runtime PM.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Set the missing pcbeep default amp for ALC668.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It's compatible with ALC269.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

current_headset_type should be of the HEADSET_TYPE enum, not the
HEADSET_MODE enum. Since ALC_HEADSET_TYPE_UNKNOWN and ALC_HEADSET_MODE_UNKNOWN
are both 0, this patch is just janitorial.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some models (or maybe depending on BIOS version) of Sony VAIO with
ALC260 give no proper pin configurations as default, resulting in the
non-working speaker, etc.  Just provide the whole pin configurations
via a fixup.
Reported-by: NMatthew Markus <mmarkus@hearit.co>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Cc: stable@vger.kernel.org (3.10+)
BugLink: https://bugs.launchpad.net/bugs/1253636Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BIOS sets MISC_NO_PRESENCE bit wrongly to the pin config on NID 0x0f.

Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The laptop has a built-in speaker on NID 0x1a.  It's an LFE only on
the right channel, so we need to provide an explicit chmap, too.

There might be other surround speakers, but they can fixed in addition
at later point, so let's fix the easier bass speaker at first.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65091Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a codec is resumed, it keeps the power on while the resuming
phase via hda_keep_power_on(), then turns down via
snd_hda_power_down().  At that point, snd_hda_power_down() notifies
the power down to the controller, and this may confuse the refcount if
the codec was already powered up before the resume.

In the end result, the controller goes to runtime suspend even before
the codec is kicked off to the power save, and the communication
stalls happens.

The fix is to add the power-up notification together with
hda_keep_power_on(), and clears the flag appropriately.

Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

You're looking at a casual headset patch,
for a specific hardware it will match,
and suddenly, the headset jack will work,
so please apply this simple quirk!

BugLink: https://bugs.launchpad.net/bugs/1253038Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... and load from the external firmware files.

The firmware binary blobs in cs46xx driver have been in a gray zone
regarding the license.  It's most likely should be OK, but still
unclear.  And, the size isn't that small, too.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=10750Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The docking station is a Thinkpad thing, so it makes sense to check
for mute/micmute LEDs for that quirk type too.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use select FW_LOADER instead of depends on.  It's more intuitive and
more consistent with other entries.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We're using the ACPI interface to detect whether we're dealing with a Thinkpad
or not. This way we're not loading the thinkpad_acpi module when we're not on
a Thinkpad, but at the same time, we give the opportunity to check for, and
potentially enable, both present and future Thinkpad with mute/micmute LEDs.

At least those running the ALC269 family (269 to 299) of Realtek codecs.

Cc: Alex Hung <alex.hung@canonical.com>
Tested-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Adds linear EQ filtering for integrated speaker protection
Signed-off-by: NVitaliy Kulikov <vitaliy.kulikov@idt.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

snd_hda_codec_reset() is called either in resetting the whole setup at
error paths or hwdep clear/reconfig sysfs triggers.  But all of these
don't assume that the power has to be off, rather they want to keep
the power state unchanged (e.g. reconfig_codec() calls the power
up/down by itself).  Thus, unconditionally clearing the power state in
snd_hda_codec_reset() leads to the inconsistency, confuses the further
operation.   This patch gets rid of the lines doing that bad thing.

Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Similarly as other laptops with AD1981 & co codecs, we can control
EAPD on AD1986A more safely depending on the Master switch, in order
to save some power.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The only EAPD on AD1986A is on NID 0x1b where usually the speaker.
But this doesn't control only the speaker amp but may influence on all
outputs, e.g. Lenovo N100 laptop seems to have this issue.

Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We don't change the EAPD bit in set_pin_eapd() if keep_eapd_on flag is
set by the codec driver and enable is false.  But, we also apply the
flipping of enable value according to inv_eapd flag in the same
function, and this confused the former check, handled as if it's
turned ON.  The inverted EAPD check must be applied after keep_eapd_on
check, instead.

Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In case there is both a multifunction headset jack and a Line Out
jack, automuting was not working properly from the Line Out jack.
This patch fixes that issue.

Cc: stable@vger.kernel.org (3.10+)
BugLink: https://bugs.launchpad.net/bugs/1250377Tested-by: NCyrus Lien <cyrus.lien@canonical.com>
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

According to the HDA specification the baseline ELD length is counted in
DW of 4 bytes instead of in bytes.

Fix the code accordingly.

Baseline length is not used by the kernel so only the ELD exported to
userspace was affected. No issues have been reported.

v2: Fixed so that eld_size is adjusted upwards accordingly as well.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The ATI/AMD video/audio latencies are specified in apparent HDMI VSDB
format. In this format values above 251 are not valid (or stream
component is not supported - 255), but no checking is performed since
this was not mentioned in the AMD HDA verbs specification.

Check that the latencies are valid before using them, and add a comment
describing the formats.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add error checks to HBR status reads (both generic and ATI/AMD) and
ATI/AMD codec reads for ELD generation.

Unchecked errors in these just caused more errors later on (invalid
codec writes for the HBR ones and ELD parsing errors for the ATI/AMD ELD
ones), but it is better to catch them earlier.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Channel map positions FLH, FCH, FRH duplicate positions TFL, TFC, TFR.
Both are the speakers above the front speakers (CEA uses "high" and USB
audio uses "top" nomenclature).

Since the USB audio code has used the TFx positions since v3.8
(04324ccc, "ALSA: usb-audio: add channel map support") but the HDMI
code only just started using FxH in a5b7d510 ("ALSA: hda -
hdmi: Fix channel maps with less common speakers") which is not yet in
any released kernel, standardize on TFx instead.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The SPDIF output MBP11,2 requires the pin control to be set/cleared
for turning on/off the optical SPDIF.  The red light turns off only
when the corresponding pin control is cleared (or powered to D3).

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401Signed-off-by: NTakashi Iwai <tiwai@suse.de>

New codec ALC255/ALC3234 support multifunction jacks.
It used for menual select the input device.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The commit [8fe7b65a: ALSA: hda - Apply GPIO setup for MacBooks
with CS4208] added a fixup entry matching with the vendor id 0x106b.
This broke the fixups for previous MBA6,1 and 6,2, since the PCI SSID
vendor id matches before evaluating the codec SSIDs.

We had a similar issue on Mac with Sigmatel codecs, and solve this
problem again similarly, by introducing a skeleton entry matching with
the all MacBooks, then remap to the right one.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401
Fixes: 8fe7b65a ('ALSA: hda - Apply GPIO setup for MacBooks with CS4208')
Cc: <stable@vger.kernel.org> [v3.12+]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Upon suspend / resume, the fixup register settings are lost because
sending HDA_FIXUP_ACT_PRE_PROBE is not part of the resume path. Instead,
write our registers in response to the HDA_FIXUP_ACT_INIT, which happens
after initial probe and upon resume.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

dmesg here has a 100+ consecutive lines of:

[ 1464.219446] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219451] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219454] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
...

Ratelimit the message to reduce the dmesg log noise.

Coalesce the format while at it.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since the recent fake ELD patches, we can remove the check for AMD
HDMI in hdmi_present_sense() and decide the return value from
eld_valid value.

Suggested by Anssi Hannula.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just added a missing ifdef:
  sound/pci/ice1712/quartet.c:210:14: warning: 'get_binary' defined but not used [-Wunused-function]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This fixes a race condition in case several monitors are being
repolled in parallel.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If the jack should not be reported to userspace (e g, because it is
in some transitional state), one can set this flag.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

There is a small gap between the jack detection unsolicited event and
the time the ELD is updated.  When user-space queries the HDMI ELD
immediately after receiving the notification, it might fail because of
this gap.

For avoiding such a problem, this patch tries to delay the HDMI jack
detect notification until ELD information is fully updated.  The
workaround is imperfect, but good enough as a starting point.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>