Currently dp83867 driver returns error if phy interface type
PHY_INTERFACE_MODE_RGMII_RXID is used to set the rx only internal
delay. Similarly issue happens for PHY_INTERFACE_MODE_RGMII_TXID.
Fix this by checking also the interface type if a particular delay
value is missing in the phy dt bindings. Also update the DT document
accordingly.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With ip6gre we have a tunnel header which also makes the tunnel MTU
smaller. We need to reserve room for it. Previously we were using up
space reserved for the Tunnel Encapsulation Limit option
header (RFC 2473).

Also, after commit b05229f4 ("gre6: Cleanup GREv6 transmit path,
call common GRE functions") our contract with the caller has
changed. Now we check if the packet length exceeds the tunnel MTU after
the tunnel header has been pushed, unlike before.

This is reflected in the check where we look at the packet length minus
the size of the tunnel header, which is already accounted for in tunnel
MTU.

Fixes: b05229f4 ("gre6: Cleanup GREv6 transmit path, call common GRE functions")
Signed-off-by: NJakub Sitnicki <jkbs@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is an IPv6 version of commit 24803f38 ("igmp: do not remove igmp
souce list..."). In mld_del_delrec(), we will restore back all source filter
info instead of flush them.

Move mld_clear_delrec() from ipv6_mc_down() to ipv6_mc_destroy_dev() since
we should not remove source list info when set link down. Remove
igmp6_group_dropped() in ipv6_mc_destroy_dev() since we have called it in
ipv6_mc_down().

Also clear all source info after igmp6_group_dropped() instead of in it
because ipv6_mc_down() will call igmp6_group_dropped().
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During interface opening MAC address stored in netdev->dev_addr is
programmed in the HW with exception of BE3 VFs where the initial
MAC is programmed by parent PF. This is OK when MAC address is not
changed when an interfaces is down. In this case the requested MAC is
stored to netdev->dev_addr and later is stored into HW during opening.
But this is not done for all BE3 VFs so the NIC HW does not know
anything about this change and all traffic is filtered.

This is the case of bonding if fail_over_mac == 0 where the MACs of
the slaves are changed while they are down.

The be2net behavior is too restrictive because if a BE3 VF has
the FILTMGMT privilege then it is able to modify its MAC without
any restriction.

To solve the described problem the driver should take care about these
privileged BE3 VFs so the MAC is programmed during opening. And by
contrast unpriviled BE3 VFs should not be allowed to change its MAC
in any case.

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NIvan Vecera <cera@cera.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BE3 VFs without FILTMGMT privilege are not allowed to modify its MAC,
VLAN table and UC/MC lists. So don't try to delete MAC on such VFs.

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NIvan Vecera <cera@cera.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return value from be_mcc_notify_wait() contains a base completion status
together with an additional status. The base_status() macro need to be
used to access base status.

Fixes: e3a7ae2c be2net: Changing MAC Address of a VF was broken
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NIvan Vecera <cera@cera.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The #warning was present 10 years ago when the driver first got merged.
As the platform is rather obsolete by now, it seems very unlikely that
the warning will cause anyone to fix the code properly.

kernelci.org reports the warning for every build in the meantime, so
I think it's better to just turn it into a code comment to reduce
noise.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to alignment requirements of the hardware transmissions are split into
two DMA descriptors, a small padding descriptor of 0 - 3 bytes in length
followed by a descriptor for rest of the packet.

In the case of IP packets the first descriptor will never be zero due to
the way that the stack aligns buffers for IP packets. However, for non-IP
packets it may be zero.

In that case it has been reported that timeouts occur, presumably because
transmission stops at the first zero-length DMA descriptor and thus the
packet is not transmitted. However, in my environment a BUG is triggered as
follows:

[   20.381417] ------------[ cut here ]------------
[   20.386054] kernel BUG at lib/swiotlb.c:495!
[   20.390324] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[   20.395805] Modules linked in:
[   20.398862] CPU: 0 PID: 2089 Comm: mz Not tainted 4.10.0-rc3-00001-gf13ad2db193f #162
[   20.406689] Hardware name: Renesas Salvator-X board based on r8a7796 (DT)
[   20.413474] task: ffff80063b1f1900 task.stack: ffff80063a71c000
[   20.419404] PC is at swiotlb_tbl_map_single+0x178/0x2ec
[   20.424625] LR is at map_single+0x4c/0x98
[   20.428629] pc : [<ffff00000839c4c0>] lr : [<ffff00000839c680>] pstate: 800001c5
[   20.436019] sp : ffff80063a71f9b0
[   20.439327] x29: ffff80063a71f9b0 x28: ffff80063a20d500
[   20.444636] x27: ffff000008ed5000 x26: 0000000000000000
[   20.449944] x25: 000000067abe2adc x24: 0000000000000000
[   20.455252] x23: 0000000000200000 x22: 0000000000000001
[   20.460559] x21: 0000000000175ffe x20: ffff80063b2a0010
[   20.465866] x19: 0000000000000000 x18: 0000ffffcae6fb20
[   20.471173] x17: 0000ffffa09ba018 x16: ffff0000087c8b70
[   20.476480] x15: 0000ffffa084f588 x14: 0000ffffa09cfa14
[   20.481787] x13: 0000ffffcae87ff0 x12: 000000000063abe2
[   20.487098] x11: ffff000008096360 x10: ffff80063abe2adc
[   20.492407] x9 : 0000000000000000 x8 : 0000000000000000
[   20.497718] x7 : 0000000000000000 x6 : ffff000008ed50d0
[   20.503028] x5 : 0000000000000000 x4 : 0000000000000001
[   20.508338] x3 : 0000000000000000 x2 : 000000067abe2adc
[   20.513648] x1 : 00000000bafff000 x0 : 0000000000000000
[   20.518958]
[   20.520446] Process mz (pid: 2089, stack limit = 0xffff80063a71c000)
[   20.526798] Stack: (0xffff80063a71f9b0 to 0xffff80063a720000)
[   20.532543] f9a0:                                   ffff80063a71fa30 ffff00000839c680
[   20.540374] f9c0: ffff80063b2a0010 ffff80063b2a0010 0000000000000001 0000000000000000
[   20.548204] f9e0: 000000000000006e ffff80063b23c000 ffff80063b23c000 0000000000000000
[   20.556034] fa00: ffff80063b23c000 ffff80063a20d500 000000013b1f1900 0000000000000000
[   20.563864] fa20: ffff80063ffd18e0 ffff80063b2a0010 ffff80063a71fa60 ffff00000839cd10
[   20.571694] fa40: ffff80063b2a0010 0000000000000000 ffff80063ffd18e0 000000067abe2adc
[   20.579524] fa60: ffff80063a71fa90 ffff000008096380 ffff80063b2a0010 0000000000000000
[   20.587353] fa80: 0000000000000000 0000000000000001 ffff80063a71fac0 ffff00000864f770
[   20.595184] faa0: ffff80063b23caf0 0000000000000000 0000000000000000 0000000000000140
[   20.603014] fac0: ffff80063a71fb60 ffff0000087e6498 ffff80063a20d500 ffff80063b23c000
[   20.610843] fae0: 0000000000000000 ffff000008daeaf0 0000000000000000 ffff000008daeb00
[   20.618673] fb00: ffff80063a71fc0c ffff000008da7000 ffff80063b23c090 ffff80063a44f000
[   20.626503] fb20: 0000000000000000 ffff000008daeb00 ffff80063a71fc0c ffff000008da7000
[   20.634333] fb40: ffff80063b23c090 0000000000000000 ffff800600000037 ffff0000087e63d8
[   20.642163] fb60: ffff80063a71fbc0 ffff000008807510 ffff80063a692400 ffff80063a20d500
[   20.649993] fb80: ffff80063a44f000 ffff80063b23c000 ffff80063a69249c 0000000000000000
[   20.657823] fba0: 0000000000000000 ffff80063a087800 ffff80063b23c000 ffff80063a20d500
[   20.665653] fbc0: ffff80063a71fc10 ffff0000087e67dc ffff80063a20d500 ffff80063a692400
[   20.673483] fbe0: ffff80063b23c000 0000000000000000 ffff80063a44f000 ffff80063a69249c
[   20.681312] fc00: ffff80063a5f1a10 000000103a087800 ffff80063a71fc70 ffff0000087e6b24
[   20.689142] fc20: ffff80063a5f1a80 ffff80063a71fde8 000000000000000f 00000000000005ea
[   20.696972] fc40: ffff80063a5f1a10 0000000000000000 000000000000000f ffff00000887fbd0
[   20.704802] fc60: fffffff43a5f1a80 0000000000000000 ffff80063a71fc80 ffff000008880240
[   20.712632] fc80: ffff80063a71fd90 ffff0000087c7a34 ffff80063afc7180 0000000000000000
[   20.720462] fca0: 0000ffffcae6fe18 0000000000000014 0000000060000000 0000000000000015
[   20.728292] fcc0: 0000000000000123 00000000000000ce ffff0000088d2000 ffff80063b1f1900
[   20.736122] fce0: 0000000000008933 ffff000008e7cb80 ffff80063a71fd80 ffff0000087c50a4
[   20.743951] fd00: 0000000000008933 ffff000008e7cb80 ffff000008e7cb80 000000100000000e
[   20.751781] fd20: ffff80063a71fe4c 0000ffff00000300 0000000000000123 0000000000000000
[   20.759611] fd40: 0000000000000000 ffff80063b1f0000 000000000000000e 0000000000000300
[   20.767441] fd60: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[   20.775271] fd80: 0000000000000000 0000000000000000 ffff80063a71fda0 ffff0000087c8c20
[   20.783100] fda0: 0000000000000000 ffff000008082f30 0000000000000000 0000800637260000
[   20.790930] fdc0: ffffffffffffffff 0000ffffa0903078 0000000000000000 000000001ea87232
[   20.798760] fde0: 000000000000000f ffff80063a71fe40 ffff800600000014 ffff000000000001
[   20.806590] fe00: 0000000000000000 0000000000000000 ffff80063a71fde8 0000000000000000
[   20.814420] fe20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001
[   20.822249] fe40: 0000000203000011 0000000000000000 0000000000000000 ffff80063a68aa00
[   20.830079] fe60: ffff80063a68aa00 0000000000000003 0000000000008933 ffff0000081f1b9c
[   20.837909] fe80: 0000000000000000 ffff000008082f30 0000000000000000 0000800637260000
[   20.845739] fea0: ffffffffffffffff 0000ffffa07ca81c 0000000060000000 0000000000000015
[   20.853569] fec0: 0000000000000003 000000001ea87232 000000000000000f 0000000000000000
[   20.861399] fee0: 0000ffffcae6fe18 0000000000000014 0000000000000300 0000000000000000
[   20.869228] ff00: 00000000000000ce 0000000000000000 00000000ffffffff 0000000000000000
[   20.877059] ff20: 0000000000000002 0000ffffcae87ff0 0000ffffa09cfa14 0000ffffa084f588
[   20.884888] ff40: 0000000000000000 0000ffffa09ba018 0000ffffcae6fb20 000000001ea87010
[   20.892718] ff60: 0000ffffa09b9000 0000ffffcae6fe30 0000ffffcae6fe18 000000000000000f
[   20.900548] ff80: 0000000000000003 000000001ea87232 0000000000000000 0000000000000000
[   20.908378] ffa0: 0000000000000000 0000ffffcae6fdc0 0000ffffa09a7824 0000ffffcae6fdc0
[   20.916208] ffc0: 0000ffffa0903078 0000000060000000 0000000000000003 00000000000000ce
[   20.924038] ffe0: 0000000000000000 0000000000000000 ffffffffffffffff ffffffffffffffff
[   20.931867] Call trace:
[   20.934312] Exception stack(0xffff80063a71f7e0 to 0xffff80063a71f910)
[   20.940750] f7e0: 0000000000000000 0001000000000000 ffff80063a71f9b0 ffff00000839c4c0
[   20.948580] f800: ffff80063a71f840 ffff00000888a6e4 ffff80063a24c418 ffff80063a24c448
[   20.956410] f820: 0000000000000000 ffff00000811cd54 ffff80063a71f860 ffff80063a24c458
[   20.964240] f840: ffff80063a71f870 ffff00000888b258 ffff80063a24c418 0000000000000001
[   20.972070] f860: ffff80063a71f910 ffff80063a7b7028 ffff80063a71f890 ffff0000088825e4
[   20.979899] f880: 0000000000000000 00000000bafff000 000000067abe2adc 0000000000000000
[   20.987729] f8a0: 0000000000000001 0000000000000000 ffff000008ed50d0 0000000000000000
[   20.995560] f8c0: 0000000000000000 0000000000000000 ffff80063abe2adc ffff000008096360
[   21.003390] f8e0: 000000000063abe2 0000ffffcae87ff0 0000ffffa09cfa14 0000ffffa084f588
[   21.011219] f900: ffff0000087c8b70 0000ffffa09ba018
[   21.016097] [<ffff00000839c4c0>] swiotlb_tbl_map_single+0x178/0x2ec
[   21.022362] [<ffff00000839c680>] map_single+0x4c/0x98
[   21.027411] [<ffff00000839cd10>] swiotlb_map_page+0xa4/0x138
[   21.033072] [<ffff000008096380>] __swiotlb_map_page+0x20/0x7c
[   21.038821] [<ffff00000864f770>] ravb_start_xmit+0x174/0x668
[   21.044484] [<ffff0000087e6498>] dev_hard_start_xmit+0x8c/0x120
[   21.050407] [<ffff000008807510>] sch_direct_xmit+0x108/0x1a0
[   21.056064] [<ffff0000087e67dc>] __dev_queue_xmit+0x194/0x4cc
[   21.061807] [<ffff0000087e6b24>] dev_queue_xmit+0x10/0x18
[   21.067214] [<ffff000008880240>] packet_sendmsg+0xf40/0x1220
[   21.072873] [<ffff0000087c7a34>] sock_sendmsg+0x18/0x2c
[   21.078097] [<ffff0000087c8c20>] SyS_sendto+0xb0/0xf0
[   21.083150] [<ffff000008082f30>] el0_svc_naked+0x24/0x28
[   21.088462] Code: d34bfef7 2a1803f3 1a9f86d6 35fff878 (d4210000)
[   21.094611] ---[ end trace 5bc544ad491f3814 ]---
[   21.099234] Kernel panic - not syncing: Fatal exception in interrupt
[   21.105587] Kernel Offset: disabled
[   21.109073] Memory Limit: none
[   21.112126] ---[ end Kernel panic - not syncing: Fatal exception in interrupt

Fixes: 2f45d190 ("ravb: minimize TX data copying")
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable BH around the call to napi_schedule() to avoid following warning

[   52.095499] NOHZ: local_softirq_pending 08
[   52.421291] NOHZ: local_softirq_pending 08
[   52.608313] NOHZ: local_softirq_pending 08

Fixes: 8d59de8f ("net/mlx4_en: Process all completions in RX rings after port goes up")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
pull request: bluetooth 2017-01-16

Here are a couple of important 802.15.4 driver fixes for the 4.10
kernel.

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
We have a number of fixes, in part because I was late
in actually sending them out - will try to do better in
the future:
 * handle VHT opmode properly when hostapd is controlling
   full station state
 * two fixes for minimum channel width in mac80211
 * don't leave SMPS set to junk in HT capabilities
 * fix headroom when forwarding mesh packets, recently
   broken by another fix that failed to take into account
   frame encryption
 * fix the TID in null-data packets indicating EOSP (end
   of service period) in U-APSD
 * prevent attempting to use (and then failing which
   results in crashes) TXQs on stations that aren't added
   to the driver yet
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When executing conntrack actions on skbuffs with checksum mode
CHECKSUM_COMPLETE, the checksum must be updated to account for
header pushes and pulls. Otherwise we get "hw csum failure"
logs similar to this (ICMP packet received on geneve tunnel
via ixgbe NIC):

[  405.740065] genev_sys_6081: hw csum failure
[  405.740106] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G          I     4.10.0-rc3+ #1
[  405.740108] Call Trace:
[  405.740110]  <IRQ>
[  405.740113]  dump_stack+0x63/0x87
[  405.740116]  netdev_rx_csum_fault+0x3a/0x40
[  405.740118]  __skb_checksum_complete+0xcf/0xe0
[  405.740120]  nf_ip_checksum+0xc8/0xf0
[  405.740124]  icmp_error+0x1de/0x351 [nf_conntrack_ipv4]
[  405.740132]  nf_conntrack_in+0xe1/0x550 [nf_conntrack]
[  405.740137]  ? find_bucket.isra.2+0x62/0x70 [openvswitch]
[  405.740143]  __ovs_ct_lookup+0x95/0x980 [openvswitch]
[  405.740145]  ? netif_rx_internal+0x44/0x110
[  405.740149]  ovs_ct_execute+0x147/0x4b0 [openvswitch]
[  405.740153]  do_execute_actions+0x22e/0xa70 [openvswitch]
[  405.740157]  ovs_execute_actions+0x40/0x120 [openvswitch]
[  405.740161]  ovs_dp_process_packet+0x84/0x120 [openvswitch]
[  405.740166]  ovs_vport_receive+0x73/0xd0 [openvswitch]
[  405.740168]  ? udp_rcv+0x1a/0x20
[  405.740170]  ? ip_local_deliver_finish+0x93/0x1e0
[  405.740172]  ? ip_local_deliver+0x6f/0xe0
[  405.740174]  ? ip_rcv_finish+0x3a0/0x3a0
[  405.740176]  ? ip_rcv_finish+0xdb/0x3a0
[  405.740177]  ? ip_rcv+0x2a7/0x400
[  405.740180]  ? __netif_receive_skb_core+0x970/0xa00
[  405.740185]  netdev_frame_hook+0xd3/0x160 [openvswitch]
[  405.740187]  __netif_receive_skb_core+0x1dc/0xa00
[  405.740194]  ? ixgbe_clean_rx_irq+0x46d/0xa20 [ixgbe]
[  405.740197]  __netif_receive_skb+0x18/0x60
[  405.740199]  netif_receive_skb_internal+0x40/0xb0
[  405.740201]  napi_gro_receive+0xcd/0x120
[  405.740204]  gro_cell_poll+0x57/0x80 [geneve]
[  405.740206]  net_rx_action+0x260/0x3c0
[  405.740209]  __do_softirq+0xc9/0x28c
[  405.740211]  irq_exit+0xd9/0xf0
[  405.740213]  do_IRQ+0x51/0xd0
[  405.740215]  common_interrupt+0x93/0x93

Fixes: 7f8a436e ("openvswitch: Add conntrack action")
Signed-off-by: NLance Richardson <lrichard@redhat.com>
Acked-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix up a data alignment issue on sparc by swapping the order
of the cookie byte array field with the length field in
struct tcp_fastopen_cookie, and making it a proper union
to clean up the typecasting.

This addresses log complaints like these:
    log_unaligned: 113 callbacks suppressed
    Kernel unaligned access at TPC[976490] tcp_try_fastopen+0x2d0/0x360
    Kernel unaligned access at TPC[9764ac] tcp_try_fastopen+0x2ec/0x360
    Kernel unaligned access at TPC[9764c8] tcp_try_fastopen+0x308/0x360
    Kernel unaligned access at TPC[9764e4] tcp_try_fastopen+0x324/0x360
    Kernel unaligned access at TPC[976490] tcp_try_fastopen+0x2d0/0x360

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_PREEMPT=y, CONFIG_IPV6=m and CONFIG_SEG6_HMAC=y,
seg6_hmac_init() is called during the initialization of the ipv6 module.
This causes a subsequent call to smp_processor_id() with preemption
enabled, resulting in the following trace.

[   20.451460] BUG: using smp_processor_id() in preemptible [00000000] code: systemd/1
[   20.452556] caller is debug_smp_processor_id+0x17/0x19
[   20.453304] CPU: 0 PID: 1 Comm: systemd Not tainted 4.9.0-rc5-00973-g46738b13 #1
[   20.454406]  ffffc9000062fc18 ffffffff813607b2 0000000000000000 ffffffff81a7f782
[   20.455528]  ffffc9000062fc48 ffffffff813778dc 0000000000000000 00000000001dcf98
[   20.456539]  ffffffffa003bd08 ffffffff81af93e0 ffffc9000062fc58 ffffffff81377905
[   20.456539] Call Trace:
[   20.456539]  [<ffffffff813607b2>] dump_stack+0x63/0x7f
[   20.456539]  [<ffffffff813778dc>] check_preemption_disabled+0xd1/0xe3
[   20.456539]  [<ffffffff81377905>] debug_smp_processor_id+0x17/0x19
[   20.460260]  [<ffffffffa0061f3b>] seg6_hmac_init+0xfa/0x192 [ipv6]
[   20.460260]  [<ffffffffa0061ccc>] seg6_init+0x39/0x6f [ipv6]
[   20.460260]  [<ffffffffa006121a>] inet6_init+0x21a/0x321 [ipv6]
[   20.460260]  [<ffffffffa0061000>] ? 0xffffffffa0061000
[   20.460260]  [<ffffffff81000457>] do_one_initcall+0x8b/0x115
[   20.460260]  [<ffffffff811328a3>] do_init_module+0x53/0x1c4
[   20.460260]  [<ffffffff8110650a>] load_module+0x1153/0x14ec
[   20.460260]  [<ffffffff81106a7b>] SYSC_finit_module+0x8c/0xb9
[   20.460260]  [<ffffffff81106a7b>] ? SYSC_finit_module+0x8c/0xb9
[   20.460260]  [<ffffffff81106abc>] SyS_finit_module+0x9/0xb
[   20.460260]  [<ffffffff810014d1>] do_syscall_64+0x62/0x75
[   20.460260]  [<ffffffff816834f0>] entry_SYSCALL64_slow_path+0x25/0x25

Moreover, dst_cache_* functions also call smp_processor_id(), generating
a similar trace.

This patch uses raw_cpu_ptr() in seg6_hmac_init() rather than this_cpu_ptr()
and disable preemption when using dst_cache_* functions.
Signed-off-by: NDavid Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __bcm_sysport_tx_reclaim() function is used to reclaim transmit
resources in different places within the driver. Most of them should
not affect the state of the transit flow control.

Introduce bcm_sysport_tx_clean() which cleans the ring, but does not
re-enable flow control towards the networking stack, and make
bcm_sysport_tx_reclaim() do the actual transmit queue flow control.

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Station structure is considered as not uploaded
(to driver) until drv_sta_state() finishes. This
call is however done after the structure is
attached to mac80211 internal lists and hashes.
This means mac80211 can lookup (and use) station
structure before it is uploaded to a driver.

If this happens (structure exists, but
sta->uploaded is false) fast_tx path can still be
taken. Deep in the fastpath call the sta->uploaded
is checked against to derive "pubsta" argument for
ieee80211_get_txq(). If sta->uploaded is false
(and sta is actually non-NULL) ieee80211_get_txq()
effectively downgraded to vif->txq.

At first glance this may look innocent but coerces
mac80211 into a state that is almost guaranteed
(codel may drop offending skb) to crash because a
station-oriented skb gets queued up on
vif-oriented txq. The ieee80211_tx_dequeue() ends
up looking at info->control.flags and tries to use
txq->sta which in the fail case is NULL.

It's probably pointless to pretend one can
downgrade skb from sta-txq to vif-txq.

Since downgrading unicast traffic to vif->txq must
not be done there's no txq to put a frame on if
sta->uploaded is false. Therefore the code is made
to fall back to regular tx() op path if the
described condition is hit.

Only drivers using wake_tx_queue were affected.

Example crash dump before fix:

 Unable to handle kernel paging request at virtual address ffffe26c
 PC is at ieee80211_tx_dequeue+0x204/0x690 [mac80211]
 [<bf4252a4>] (ieee80211_tx_dequeue [mac80211]) from
 [<bf4b1388>] (ath10k_mac_tx_push_txq+0x54/0x1c0 [ath10k_core])
 [<bf4b1388>] (ath10k_mac_tx_push_txq [ath10k_core]) from
 [<bf4bdfbc>] (ath10k_htt_txrx_compl_task+0xd78/0x11d0 [ath10k_core])
 [<bf4bdfbc>] (ath10k_htt_txrx_compl_task [ath10k_core])
 [<bf51c5a4>] (ath10k_pci_napi_poll+0x54/0xe8 [ath10k_pci])
 [<bf51c5a4>] (ath10k_pci_napi_poll [ath10k_pci]) from
 [<c0572e90>] (net_rx_action+0xac/0x160)
Reported-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ibss and mesh modes copy the ht capabilites from the band without
overriding the SMPS state. Unfortunately the default value 0 for the
SMPS field means static SMPS instead of disabled.

This results in HT ibss and mesh setups using only single-stream rates,
even though SMPS is not supposed to be active.

Initialize SMPS to disabled for all bands on ieee80211_hw_register to
ensure that the value is sane where it is not overriden with the real
SMPS state.
Reported-by: NElektra Wagenrad <onelektra@gmx.net>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
[move VHT TODO comment to a better place]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

While probing BGX we requesting appropriate QLM for it's configuration
and get LMAC count by that request. Then, while reading configured
MAC values from SSDT table we need to save them in proper mapping:
  BGX[i]->lmac[j].mac = <MAC value>
to later provide for initialization stuff. In order to fill
such mapping properly we need to add lmac index to be used while
acpi initialization since at this moment bgx->lmac_count already contains
actual value.
Signed-off-by: NVadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the addition of the frame_retries callback we could run into cases where
a ATUSB device with an older firmware version would now longer be able to bring
the interface up.

We keep this functionality disabled now if the minimum firmware version for this
feature is not available.

Fixes: 5d82288b ("ieee802154: atusb: implement .set_frame_retries
ops callback")
Reported-by: NAlexander Aring <aar@pengutronix.de>
Acked-by: NAlexander Aring <aar@pengutronix.de>
Signed-off-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Driver code never touches "rstn" signal in atomic context, so there's
no need to implicitly put such restriction on it by using gpio_set_value
to manipulate it. Replace gpio_set_value to gpio_set_value_cansleep to
fix that.

As a an example of where such restriction might be inconvenient,
consider a hardware design where "rstn" is connected to a pin of I2C/SPI
GPIO expander chip.

Cc: Chris Healy <cphealy@gmail.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

From 4.9 we should really avoid using the stack here as this will not be DMA
able on various platforms. This changes a buffer that was introduced in the
4.10 merge window.

Fixes: 6cc33eba ("ieee802154: atusb: try to read permanent extended
address from device")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In the unlikely case were the firmware is new enough but the actual USB command
still fails make sure we set a random address and return.
Signed-off-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

From 4.9 we should really avoid using the stack here as this will not be DMA
able on various platforms. This changes the buffers already being present in
time of 4.9 being released. This should go into stable as well.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

rtm_table is an 8-bit field while table ids are allowed up to u32. Commit
709772e6 ("net: Fix routing tables with id > 255 for legacy software")
added the preference to set rtm_table in dumps to RT_TABLE_COMPAT if the
table id is > 255. The table id returned on get route requests should do
the same.

Fixes: c36ba660 ("net: Allow user to get table id from route lookup")
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 6ffe1c4c ("net: qcom/emac: fix of_node and phydev leaks")
fixed the problem with reference leaks on phydev, but the fix is
device-tree specific.  When the driver unloads, the reference is
dropped only on DT systems.

Instead, it's cleaner if up grab an reference on ACPI systems.
When the driver unloads, we can drop the reference without having
to check whether we're on a DT system.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Reviewed-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle failure in lwtunnel_fill_encap adding attributes to skb.

Fixes: 571e7226 ("ipv4: support for fib route lwtunnel encap attributes")
Fixes: 19e42e45 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove Rx overflow log messages as in an environment where logging results
in network traffic logging may cause further overflows.

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: reworked changelog]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Couple of fixes

Couple of simple fixes from Arkadi and Elad.

Please queue these up for stable. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The event_data starts from address 0x00-0x0C and not from 0x08-0x014. This
leads to duplication with other fields in the Event Queue Element such as
sub-type, cqn and owner.

Fixes: eda6500a ("mlxsw: Add PCI bus implementation")
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During transmission the skb is checked for headroom in order to
add vendor specific header. In case the skb needs to be re-allocated,
skb_realloc_headroom() is called to make a private copy of the original,
but doesn't release it. Current code assumes that the original skb is
released during reallocation and only releases it at the error path
which causes a memory leak.

Fix this by adding the original skb release to the main path.

Fixes: d003462a ("mlxsw: Simplify mlxsw_sx_port_xmit function")
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During transmission the skb is checked for headroom in order to
add vendor specific header. In case the skb needs to be re-allocated,
skb_realloc_headroom() is called to make a private copy of the original,
but doesn't release it. Current code assumes that the original skb is
released during reallocation and only releases it at the error path
which causes a memory leak.

Fix this by adding the original skb release to the main path.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The receive callback (in tasklet context) is using RCU to get reference
to associated VF network device but this is not safe. RCU read lock
needs to be held. Found by running with full lockdep debugging
enabled.

Fixes: f207c10d ("hv_netvsc: use RCU to protect vf_netdev")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise, a xfrm policy with sport/dport being set cannot be matched.
Signed-off-by: NMartynas Pumputis <martynas@weave.works>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the hw rx checksum is always enabled, and the user couldn't switch
it to sw rx checksum.

Note that the RTL_VER_01 only support sw rx checksum only. Besides,
the hw rx checksum for RTL_VER_02 is disabled after
commit b9a321b4 ("r8152: Fix broken RX checksums."). Re-enable it.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge fixes from Andrew Morton:
 "27 fixes.

  There are three patches that aren't actually fixes. They're simple
  function renamings which are nice-to-have in mainline as ongoing net
  development depends on them."

* akpm: (27 commits)
  timerfd: export defines to userspace
  mm/hugetlb.c: fix reservation race when freeing surplus pages
  mm/slab.c: fix SLAB freelist randomization duplicate entries
  zram: support BDI_CAP_STABLE_WRITES
  zram: revalidate disk under init_lock
  mm: support anonymous stable page
  mm: add documentation for page fragment APIs
  mm: rename __page_frag functions to __page_frag_cache, drop order from drain
  mm: rename __alloc_page_frag to page_frag_alloc and __free_page_frag to page_frag_free
  mm, memcg: fix the active list aging for lowmem requests when memcg is enabled
  mm: don't dereference struct page fields of invalid pages
  mailmap: add codeaurora.org names for nameless email commits
  signal: protect SIGNAL_UNKILLABLE from unintentional clearing.
  mm: pmd dirty emulation in page fault handler
  ipc/sem.c: fix incorrect sem_lock pairing
  lib/Kconfig.debug: fix frv build failure
  mm: get rid of __GFP_OTHER_NODE
  mm: fix remote numa hits statistics
  mm: fix devm_memremap_pages crash, use mem_hotplug_{begin, done}
  ocfs2: fix crash caused by stale lvb with fsdlm plugin
  ...

Pull networking fixes from David Miller:

 1) Fix rtlwifi crash, from Larry Finger.

 2) Memory disclosure in appletalk ipddp routing code, from Vlad
    Tsyrklevich.

 3) r8152 can erroneously split an RX packet into multiple URBs if the
    Rx FIFO is not empty when we suspend. Fix this by waiting for the
    FIFO to empty before suspending. From Hayes Wang.

 4) Two GRO fixes (enter slow path when not enough SKB tail room exists,
    disable frag0 optimizations when there are IPV6 extension headers)
    from Eric Dumazet and Herbert Xu.

 5) A series of mlx5e bug fixes (do source udp port offloading for
    tunnels properly, Ip fragment matching fixes, handling firmware
    errors properly when installing TC rules, etc.) from Saeed Mahameed,
    Or Gerlitz, Roi Dayan, Hadar Hen Zion, Gil Rockah, and Daniel
    Jurgens.

 6) Two VRF fixes from David Ahern (don't skip multipath selection for
    VRF paths, disallow VRF to be configured with table ID 0).

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
  net: vrf: do not allow table id 0
  net: phy: marvell: fix Marvell 88E1512 used in SGMII mode
  sctp: Fix spelling mistake: "Atempt" -> "Attempt"
  net: ipv4: Fix multipath selection with vrf
  cgroup: move CONFIG_SOCK_CGROUP_DATA to init/Kconfig
  gro: use min_t() in skb_gro_reset_offset()
  net/mlx5: Only cancel recovery work when cleaning up device
  net/mlx5e: Remove WARN_ONCE from adaptive moderation code
  net/mlx5e: Un-register uplink representor on nic_disable
  net/mlx5e: Properly handle FW errors while adding TC rules
  net/mlx5e: Fix kbuild warnings for uninitialized parameters
  net/mlx5e: Set inline mode requirements for matching on IP fragments
  net/mlx5e: Properly get address type of encapsulation IP headers
  net/mlx5e: TC ipv4 tunnel encap offload error flow fixes
  net/mlx5e: Warn when rejecting offload attempts of IP tunnels
  net/mlx5e: Properly handle offloading of source udp port for IP tunnels
  gro: Disable frag0 optimization on IPv6 ext headers
  gro: Enter slow-path if there is no tailroom
  mlx4: Return EOPNOTSUPP instead of ENOTSUPP
  net/af_iucv: don't use paged skbs for TX on HiperSockets
  ...

Pull crypto fix from Herbert Xu:
 "This fixes a regression in aesni that renders it useless if it's
  built-in with a modular pcbc configuration"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: aesni - Fix failure when built-in with modular pcbc

When an associated station changes its VHT operating mode this
can/will affect the bandwidth it's using, and consequently we
must recalculate the minimum bandwidth we need to use. Failure
to do so can lead to one of two scenarios:
 1) we use a too high bandwidth, this is benign
 2) we use a too narrow bandwidth, causing rate control and
    actual PHY configuration to be out of sync, which can in
    turn cause problems/crashes
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In the current minimum chandef code there's an issue in that the
recalculation can happen after rate control is initialized for a
station that has a wider bandwidth than the current chanctx, and
then rate control can immediately start using those higher rates
which could cause problems.

Observe that first of all that this problem is because we don't
take non-associated and non-uploaded stations into account. The
restriction to non-associated is quite pointless and is one of
the causes for the problem described above, since the rate init
will happen before the station is set to associated; no frames
could actually be sent until associated, but the rate table can
already contain higher rates and that might cause problems.

Also, rejecting non-uploaded stations is wrong, since the rate
control can select higher rates for those as well.

Secondly, it's then necessary to recalculate the minimal config
before initializing rate control, so that when rate control is
initialized, the higher rates are already available. This can be
done easily by adding the necessary function call in rate init.

Change-Id: Ib9bc02d34797078db55459d196993f39dcd43070
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, this attribute is only fetched on station addition, but
not on station change. Since this info is only present in the assoc
request, with full station state support in the driver it cannot be
present when the station is added.

Thus, add support for changing the VHT opmode on station update if
done before (or while) the station is marked as associated. After
this, ignore it, since it used to be ignored.
Signed-off-by: NBeni Lev <beni.lev@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>