tda1004x doesn't allow firmware loads while it is busy with something
else. Avoid it to happen by locking the I2C bus during firmware transfer.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The previous website doesn't exist anymore. Update it to one site that
actually exists.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use managed functions to clean up the error handling code and function
mx2_camera_remove().  Along with the change, a few variables get removed
from struct mx2_camera_dev.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: NJavier Martin <javier.martin@vista-silicon.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is a piece of code becoming dead since commit 2c9ba37d ([media]
V4L: mx2_camera: remove unsupported i.MX27 DMA mode, make EMMA
mandatory).  It should have been removed together with the commit.
Remove it now.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NJavier Martin <javier.martin@vista-silicon.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Callbacks were set even attach failed. This leads calling
.release() in error case and resulted crash.
Reported-by: NOliver Schinagl <oliver@schinagl.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Callbacks were set even attach failed. This leads calling
.release() in error case and resulted crash.
Reported-by: NOliver Schinagl <oliver@schinagl.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

fe was not set NULL after it was destroyed in tuner attach fail
error case. Due to that it was destroyed again and Kernel oopsed.
Reported-by: NOliver Schinagl <oliver@schinagl.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

* better readability
* make checkpatch.pl happy
* few bytes smaller binary footprint
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Refactor firmware download function. It also should fix one bug
coming from usb_control_msg() message buffers. Taking buffers from
the stack for usb_control_msg() is not allowed as it does not work
on all architectures. Allocate buffers using kmalloc().
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is 4 x RTL2832U + 4 x FC0012 in one PCIe board.
Of course there is a PCIe USB host controller too.
Big thanks for Darryl Bond reporting and testing that!
Reported-by: NDarryl Bond <darryl.bond@gmail.com>
Tested-by: NDarryl Bond <darryl.bond@gmail.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is initial support for the Asus MyCinema U3100Mini Plus. The driver
in its current form gets detected and loads properly.
Scanning using dvbscan works without problems, Locking onto a channel
using tzap also works fine. Only playback using tzap -r + mplayer was
tested and was fully functional.
It uses the af9035 USB Bridge chip, with an af9033 demodulator. The tuner
used is the FCI FC2580.
Signed-off-by: NOliver Schinagl <oliver@schinagl.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Do not abuse anymore fc0012 tuner config.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is just stub implementation, remove it.
Also add debug for beginning of fe callback.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Move rtl2831u tuner probing correct place.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use of frontend callback is highly hardware design dependent
and whole callback could be optional in many cases. Returning
error by default when callback is not implemented is stupid.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Implement masked register write and use it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Move rtl2832u tuner probing correct place.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Logically it is better ask hardware to stop streaming before
killing urbs carrying stream. Earlier it was just opposite.
Now code runs:
* submit urbs
* start streaming
** streaming ongoing **
* stop streaming
* kill urbs
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I think it is better name. At that phase renaming is quite painless
as module is not yet merged to mainline Kernel.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently there is LNA behind cxd2820r demodulator GPIO. Use
Kernel GPIO interface to access those GPIOs.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Demodulator cannot perform statistic IOCTLs when it is not tuned.
Return -EAGAIN in such case.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes checkpatch warnings related to printk.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
[laurent.pinchart@ideasonboard.com Replaced EBUSY with ENODEV]
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

At commit 07d106d0, Linus pointed out that ENOIOCTLCMD should be
translated as ENOTTY to user mode.
Signed-off-by: NWanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Also change location of other RTL2832 reference design ID 0bda:2838.
I just like to see reference design IDs at the first IDs in the list.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This replaces BUG_ON() calls with WARN_ON(), and returns
EINVAL if some parameter is NULL, as suggested by Jonathan and Mauro.
The BUG_ON() call is too drastic to be used in this case.
See the full discussion here:
http://www.spinics.net/lists/linux-media/msg52462.htmlSigned-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This function returns an integer and it's mandatory
to check the return code.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>