Add support for AT26Fxxx dataflash devices. These devices have a quite different
commandset than the AT45xxx chips, which are handled by at91_dataflash.c, so a
combined driver turned out to be more ugly than useful.

Tested only on AT26F004.
Signed-off-by: NHans-Jürgen Koch <hjk@linutronix.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The ops.len member is not initialized, because it is unused for this
operation. The length check needs to use ops.ooblen instead
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The support for obsolete ancient NAND chips adds .data size and one
of the old ids conflicts with a modern one. Make the support for
such chips depending on a config option.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Use the functions in the ecc structure instead of the default ones,
so the override by the board driver is effective also for software ecc
code paths.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Add Micron Manufacturer ID.
Signed-off-by: NShahrom Sharif <sshahrom@micron.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Check the node CRC on scan before doing anything else with the node.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

 o A dependency on the processor architecture does not make sense;
   delete it.
 o The Alchemy and MTX drivers requires MTD_PARTITIONS and MTD_CFI to work,
   make those dependencies.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Delete RCS $Id string and unused debug code.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Auto unlock sectors on resume for auto locking flash on power up.
Signed-off-by: NRodolfo Giometti <giometti@enneenne.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Delete everything related to the apparently non-existent kernel config
option JFFS2_PROC.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Add flash and rootfs mappings for the PMC-Sierra MSP71xx devices.

This patch references some platform support files previously submitted to
the linux-mips@linux-mips.org list.
Signed-off-by: NMarc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Delete the unreferenced header file include/linux/mtd/iflash.h.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

We'll need them for suspend/resume.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

  Delete the obsolete source file fs/jffs2/comprtest.c.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPV6] fix ipv6_getsockopt_sticky copy_to_user leak
  [IPV6]: Fix for ipv6_setsockopt NULL dereference
  [DCCP]: Initialise write_xmit_timer also on passive sockets
  [IPV4]: Fix rtm_to_ifaddr() error handling.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] refresh config files
  [IA64] put kdump_find_rsvd_region in __init
  [IA64] Remove sparse warning from unwind code
  [IA64] add missing syscall trace clear
  [IA64] Cleanup in crash.c
  [IA64] kexec: declare ia64_mca_pal_base in mca.h rather than kexec.h
  [IA64] pci_get_legacy_ide_irq should return irq (not GSI)
  [IA64] whitespace fixes for include/asm-ia64/sal.h
  [IA64] Cache error recovery
  [IA64] Proper handling of TLB errors from duplicate itr.d dropins

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  kobject: new_device->kref wasn't putted after error in kobject_move()
  driver core: export device_rename
  Remove devfs from MAINTAINERS
  Driver core: add device symlink back to sysfs
  Revert "driver core: refcounting fix"

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
  pci: fix section mismatch warning
  PCI: aer: fix section mismatch warning
  pcie: fix section mismatch warning
  PCI: allow multiple calls to pcim_pin_device()

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (23 commits)
  USB Elan FTDI: check for workqueue creation
  USB: fix spinlock recursion in cdc-acm.c
  USB: fix Unaligned access in EHCI driver
  USB: Product ID for FT232RL in ftdi_sio
  USBNET: DM9501: Add Corega FEther USB-TXC support.
  USB: ipaq.c: Additional devices
  USB: further fix for usb-serial
  USB: fix usb-serial device naming bug
  USB: RTS/DTR signal patch for airprime driver
  USB: ftdi_sio: use port_probe / port_remove thereby fixing access to the latency_timer
  usb-serial: fix shutdown / device_unregister order
  USB: add Additional PIDs in ftdi_sio
  USB: add QL355P power supply ids to fdti_sio
  USB: New device IDs for cp2101 driver
  USB: kill dead code from hub.c
  USB: ratelimit debounce error messages
  USB: pxa2xx_udc: fix hardcoded irq number
  UHCI: fix port resume problem
  USB: set the correct interval for interrupt URBs
  USB: goku_udc: Remove crude cache coherency code
  ...

Delay the read of the EC status register until
after the event that caused it occurs -- otherwise
it is possible to read and act on stale status that was
associated with the previous event.

Do this with a perpetually incrementing "event_count" to detect
when a new event occurs and it is safe to read status.

There is no workaround for polling mode -- it is inherently
exposed to reading and acting on stale status, since it
doesn't have an interrupt to tell it the event completed.

http://bugzilla.kernel.org/show_bug.cgi?id=8110Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Avoid NULL pointer usage if workqueue creation failed.
Signed-off-by: NCyrill Gorcunov <gorcunov@gmail.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this fixes the spinlock recursion issue. The older fix was incomplete.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Acked-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I get following warnings on spar64:
Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd]

Despite of the comment in the patched code, the type cast used there
does make unaligned access. The fix was made as it's done in
ohci-hub.c.
Signed-off-by: NMax Dmitrichenko <dmitrmax@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.

From: Gard Spreemann <spreeman@stud.ntnu.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Additional devices
Signed-off-by: NAndre Spahlinger <uenz@gmx.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this is a fix for the outstanding usb-serial issues.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter:
> Hi Greg
> 
> 34ef50e5 is definitely
> the source of the problem. Reverting that makes the
> ftdi port show up as ttyUSB0 again for me and it
> can actually be opened.

This patch should fix the issue.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NCraig Schlenter <craig@codefountain.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:

Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem.  Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.

With the attached patch, the RTS/DTR lines are resetted on a close.  The
code was mainly taken from the option.c driver.