The code calculating HDMI PLL parameters has always been very confusing.
Now that we are implementing a common PLL library for the DSS, it's
important that the PLL code is understandable.

This patch rewrites the calculation code, and removes a few hacks that
were used there.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We don't support interlace modes properly on OMAP5+ HDMI, so we need to
reject interlace timings.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Only OMAP5+ has REFSEL field, but at the moment it's set also on OMAP4.

Fix this by adding a "has_refsel" field, and setting the REFSEL based on
that.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that we have the common DSS PLL support, change DSI to use it. This
results in quite a lot of changes, but almost all of them are trivial
name changes.

The functions to calculate and program the PLL settings can be removed
from dsi.c, as the common PLL API contains the same functionality.

We also need to create struct dss_pll_hw entries for PLL hardware
features for different OMAP platforms, instead of using the
dss_features.c as the old code does.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP DSS currently contains two different PLLs: DSI PLL (Type A PLL) and
HDMI PLL (Type B PLL). When DRA7 support is added, we will also support
Video PLLs (Type A).

The driver currently handles all PLLs totally separately. This patch
adds common DSS PLL code, which

a) lets us have common code for the PLLs
b) lets the users of the PLLs use a common API, instead of DSI API or
   HDMI API.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When DPI uses the DSI PLL for pixel clock, the DPI code will call
dsi_runtime_get/put to keep the DSI block enabled. A much simpler way to
handle this is to do dsi_runtime_get/put in DSI's dsi_pll_init() and
dsi_pll_uninit(), thus removing the need for DSI to call the runtime PM
functions.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The HSDIV outputs of DSI PLL (and also other PLLs) all have the same
bit width for the divider value.

Simplify the code by merging HSDIV divider widths into one width.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are creating a common DSS PLL code, so having fixed DSI specific
hsdiv fields in the clock information is not ok.

This patch changes the hsdiv fields to arrays, so that we can use all
the 4 possible hsdiv outputs (DSI only usees 2), and we have generic way
to access the hsdivs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are creating a common DSS PLL code, so rename 'clkin4ddr' field,
which is DSI specific name, to 'clkdco' which is a generic name.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that dsi_clock_info only contains information about the PLL, we can
just copy the whole struct when storing the clock information, instead
of copying individual fields.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We have pll_locked field in struct dsi_data, but it doesn't have any
meaningful use anymore, and can be removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

struct dsi_clock_info contains clkin field, which is the rate of the
PLL's input clock. This field is not needed, as it can be easily
retrieved by using the clk_get_rate().

This patch removes the clkin field.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

struct dsi_clock_info represents the clocks handled by the DSI, mostly
PLL related clocks. In an effort to create common PLL code, we need to
remove all the non-PLL items from dsi_clock_info.

This patch removes LP clock related fields from dsi_clock_info, and
creates a new struct dsi_lp_clock_info for holding clock info for the LP
clock.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DSS PLL has support to power on the PLL's highspeed clock output
and HSDIV output separately. In practice both need to powered on, as in
most OMAP's that's the only working configuration. We already do that in
dsi_pll_init(), by overriding the passed arguments so that both are
always powered.

Simplify the code by removing the support for choosing which outputs to
power on.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

With the previous patch "OMAPDSS: DSI: wait for hsdiv clocks when
enabling PLL",  dsi_wait_pll_hsdiv_dispc_active and
dsi_wait_pll_hsdiv_dsi_active are no longer needed, so they and the
callers can be removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

At the moment we have two functions to wait for the HSDIV clocks to get
active, dsi_wait_pll_hsdiv_dispc_active and
dsi_wait_pll_hsdiv_dsi_active. Instead of such inconvenient functions,
let's just make sure that the hsdiv clocks are active after the pll has
been enabled.

This patch adds code to dsi_pll_set_clock_div() to wait until HSDIV
clocks are active.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add a 'port' parameter in dpi_select_source. The param tells the port
number of the DPI instance that we want to configure. We use this number
to select the overlay manager for that DPI instance.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Register DPI outputs, and assign the port_num to them as specified by the
'reg' property in the DPI ports in DT.

To support multiple DPI instances, dpi_get_channel needs to take the DPI
instance's port number to get the corresponding channel. Make it take this
argument. We just pass 0 in the non-DT path, since we don't support multiple
instances in the non-DT case.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In omapdss_of_find_source_for_first_ep, we retrieve a source endpoint's DT node,
and then see what omapdss output has the matching device_node pointer in
omap_dss_find_output_by_node.

For all DPI and SDI outputs, the device_node pointer is set as the parent's DSS
device_node pointer. If the source is one of these outputs, the above method
won't work.

To get the correct output for ports within DSS(and in other cases in the future,
where multiple ports might be under one device), we require additional
information which is exclusive to the output port.

We create a new field in omap_dss_device called 'port_num', this provides port
number of the output port corresponding to this device. When searching for the
source endpoint in DT, we extract the 'reg' property from the port corresponding
to the endpoint source. From the list of registered outputs, we pick out that
output which has both dev->of_node and port_num matching with the device_node
pointer and 'reg' of the source endpoint node from DT.

For encoder blocks(the ones which have both an input and output port), we need
to set the port_num as the 'reg' property for the output port as defined in the
DT bindings. We set port_num to 1 in the tfp410 and tpd12s015 encoder drivers.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The init/uninit port functions are used to set up the DPI and SDI outputs under
the dss platform device. A 'reg' property is used to determine the port number
of the output. This tells us whether the port is DPI or SDI for OMAP34xx DSS
revision. For other DSS revisions, we only have DPI outputs under the dss
platform device.

For multiple DPI output instances(introduced in DRA7xx DSS), we will use the
the port number to specify which DPI output instance is being inited.

The current functions work fine if there is only one DPI output instance in
DSS. For multiple DPI instances, it would get complicated to figure out whether
port number was used to specify whether the output is SDI, or another DPI
instance.

We create a list of port types supported for each DSS rev, with the index of the
port in the list specifying the port number of the output for that DSS revision.
This allows us to have a more generic way to init/uninit ports within DSS, and
also support multiple DPI ports.

We make the uninit_port functions iterative since we will have multiple DPI
ports to uninit in the future.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DPI and SDI ports are backed by only one parent DSS device. We don't have a
corresponding platform_device for ports under DSS. In order to support multiple
instances of DPI, we need to pass the driver data pointer through the DPI port's
private data ('data' member in device_node struct).

dpi_init_output/dpi_uninit_output are untouched and only used for non-DT case,
these are called when the DPI platform device probed/removed. These funcs will
be removed when non-DT mode is removed.

dpi_init_output_port/dpi_uninit_output_port are created and used for the DT
path, called when DSS inits/uninits it's ports. These new functions retrieve
the dpi_data pointer from 'port->data', and not from the platform device's
data(pdev->dev) like in the non-DT path.

We add some code in dss_uninit_ports() to pass a pointer to the DPI port in
dpi_uninit_port().
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Allocate driver data(dpi_data) for each DPI instance. It's allocated in
omap_dpi_probe() when DT isn't used, and in dpi_init_port() when DT is used.
The dpi_data struct instance is no longer global. In the case of DPI ops, it's
retrieved from dpi_get_data_from_dssdev(). 'dssdev' passed by the connected
encoder/panel driver is a pointer to the 'output' member in dpi_data, and thus
can be used to get the DPI instance's driver data. In the case of probe/ini_port
functions, it's set as DPI/DSS device's private data embedded in the
platform_device struct.

Having dpi_data as private data of the platform device will not work for
multiple DPI instances in the DT case. This is because there is no corresponding
platform_device for DPI or SDI, they exist only as ports under the parent DSS
platform_device in the DT case. The DPI port's private data('data' member in
device_node struct) will later be used to store dpi_data.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DPI related data is currently a static global struct parameter. It is accessed
directly by functions in the driver.

This method won't work if we want the driver to support multiple DPI instances.
Create struct dpi_data, and pass its pointer to functions which need to use it.

We still have a static instance defined for dpi_data, which is accessed by top
level DPI ops. This will be removed when the driver dynamically allocates
dpi_data for each DPI instance.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Pull MTD fixes from Brian Norris:
 "Three main MTD fixes for 3.18:

   - A regression from 3.16 which was noticed in 3.17.  With the
     restructuring of the m25p80.c driver and the SPI NOR library
     framework, we omitted proper listing of the SPI device IDs.  This
     means m25p80.c wouldn't auto-load (modprobe) properly when built as
     a module.  For now, we duplicate the device IDs into both modules.

   - The OMAP / ELM modules were depending on an implicit link ordering.
     Use deferred probing so that the new link order (in 3.18-rc) can
     still allow for successful probing.

   - Fix suspend/resume support for LH28F640BF NOR flash"

* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
  mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
  mtd: omap: fix mtd devices not showing up
  mtd: m25p80,spi-nor: Fix module aliases for m25p80
  mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
  mtd: m25p80: get rid of spi_get_device_id

Pull SCSI fixes from James Bottomley:
 "This is a set of six patches consisting of:
   - two MAINTAINER updates
   - two scsi-mq fixs for the old parallel interface (not every request
     is tagged and we need to set the right flags to populate the SPI
     tag message)
   - a fix for a memory leak in scatterlist traversal caused by a
     preallocation update in 3.17
   - an ipv6 fix for cxgbi"

[ The scatterlist fix also came in separately through the block layer tree ]

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  MAINTAINERS: ufs - remove self
  MAINTAINERS: change hpsa and cciss maintainer
  libcxgbi : support ipv6 address host_param
  scsi: set REQ_QUEUE for the blk-mq case
  Revert "block: all blk-mq requests are tagged"
  lib/scatterlist: fix memory leak with scsi-mq

Pull drm fixes from Dave Airlie:
 "Nothing too astounding or major: radeon, i915, vmwgfx, armada and
  exynos.

  Biggest ones:
   - vmwgfx has one big locking regression fix
   - i915 has come displayport fixes
   - radeon has some stability and a memory alloc failure
   - armada and exynos have some vblank fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
  drm/exynos: correct connector->dpms field before resuming
  drm/exynos: enable vblank after DPMS on
  drm/exynos: init kms poll at the end of initialization
  drm/exynos: propagate plane initialization errors
  drm/exynos: vidi: fix build warning
  drm/exynos: remove explicit encoder/connector de-initialization
  drm/exynos: init vblank with real number of crtcs
  drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
  drm/vmwgfx: Fix hash key computation
  drm/vmwgfx: fix lock breakage
  drm/i915/dp: only use training pattern 3 on platforms that support it
  drm/radeon: remove some buggy dead code
  drm/i915: Ignore VBT backlight check on Macbook 2, 1
  drm/radeon: remove invalid pci id
  drm/radeon: dpm fixes for asrock systems
  radeon: clean up coding style differences in radeon_get_bios()
  drm/radeon: Use drm_malloc_ab instead of kmalloc_array
  drm/radeon/dpm: disable ulv support on SI
  drm/i915: Fix GMBUSFREQ on vlv/chv
  drm/i915: Ignore long hpds on eDP ports
  ...

Pull ARM fixes from Russell King:
 - add the new bpf syscall to ARM.
 - drop a redundant return statement in __iommu_alloc_remap()
 - fix a performance issue noticed by Thomas Petazzoni with
   kmap_atomic().
 - fix an issue with the L2 cache OF parsing code which caused it to
   incorrectly print warnings on each boot, and make the warning text
   more consistent with the rest of the code

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
  ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
  ARM: 8181/1: Drop extra return statement
  ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
  ARM: enable bpf syscall

Pull kvm fixes from Paolo Bonzini:
 "A small set of x86 fixes.  The most serious is an SRCU lockdep fix.

  A bit late - needed some time to test the SRCU fix, which only came in
  on Friday"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: vmx: defer load of APIC access page address during reset
  KVM: nVMX: Disable preemption while reading from shadow VMCS
  KVM: x86: Fix far-jump to non-canonical check
  KVM: emulator: fix execution close to the segment limit
  KVM: emulator: fix error code for __linearize

Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes

This pull-request includes some bug fixes and code cleanups.
Especially, this fixes the bind failure issue occurred when it tries
to re-bind Exynos drm driver after unbound, and the modetest failure
issue incurred by not having a pair to vblank on and off requests.

* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: correct connector->dpms field before resuming
  drm/exynos: enable vblank after DPMS on
  drm/exynos: init kms poll at the end of initialization
  drm/exynos: propagate plane initialization errors
  drm/exynos: vidi: fix build warning
  drm/exynos: remove explicit encoder/connector de-initialization
  drm/exynos: init vblank with real number of crtcs

Pull VFS fixes from Al Viro:
 "A bunch of assorted fixes, most of them followups to overlayfs merge"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ovl: initialize ->is_cursor
  Return short read or 0 at end of a raw device, not EIO
  isofs: don't bother with ->d_op for normal case
  isofs_cmp(): we'll never see a dentry for . or ..
  overlayfs: fix lockdep misannotation
  ovl: fix check for cursor
  overlayfs: barriers for opening upper-layer directory
  rcu: Provide counterpart to rcu_dereference() for non-RCU situations
  staging: android: logger: Fix log corruption regression

The sk_prot is irda's own set of protocol handlers, so irda should
statically know what that function is anyway, without using an indirect
pointer.  And as it happens, we know *exactly* what that pointer is
statically: it's NULL, because irda doesn't define a disconnect
operation.

So calling that function is doubly wrong, and will just cause an oops.
Reported-by: NMartin Lang <mlg.hessigheim@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During system suspend after connector switch off its dpms field
is set to connector previous dpms state. To properly resume dpms field
should be set to its actual state (off) before resuming to previous dpms state.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Before DPMS off driver disables vblank.
It should be balanced by vblank enable after DPMS on.
The patch fixes issue with page_flip ioctl not being able
to acquire vblank counter introduced by patch:
drm: Always reject drm_vblank_get() after drm_vblank_off()
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

HPD events can be generated by components even if drm_dev is not fully
initialized, to skip such events kms poll initialization should
be performed at the end of load callback followed directly by forced
connection detection.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

In case of error during plane initialization load callback
incorrectly return success, this patch fixes it.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

encoder object isn't used anymore so remove it.
Signed-off-by: NInki Dae <inki.dae@samsung.com>

All KMS objects are destroyed by drm_mode_config_cleanup in proper order
so component drivers should not care about it.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Initialization of vblank with MAX_CRTC caused attempts
to disabling vblanks for non-existing crtcs in case
drm used fewer crtcs. The patch fixes it.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Most call paths to vmx_vcpu_reset do not hold the SRCU lock.  Defer loading
the APIC access page to the next vmentry.

This avoids the following lockdep splat:

[ INFO: suspicious RCU usage. ]
3.18.0-rc2-test2+ #70 Not tainted
-------------------------------
include/linux/kvm_host.h:474 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 0
1 lock held by qemu-system-x86/2371:
 #0:  (&vcpu->mutex){+.+...}, at: [<ffffffffa037d800>] vcpu_load+0x20/0xd0 [kvm]

stack backtrace:
CPU: 4 PID: 2371 Comm: qemu-system-x86 Not tainted 3.18.0-rc2-test2+ #70
Hardware name: Dell Inc. OptiPlex 9010/0M9KCM, BIOS A12 01/10/2013
 0000000000000001 ffff880209983ca8 ffffffff816f514f 0000000000000000
 ffff8802099b8990 ffff880209983cd8 ffffffff810bd687 00000000000fee00
 ffff880208a2c000 ffff880208a10000 ffff88020ef50040 ffff880209983d08
Call Trace:
 [<ffffffff816f514f>] dump_stack+0x4e/0x71
 [<ffffffff810bd687>] lockdep_rcu_suspicious+0xe7/0x120
 [<ffffffffa037d055>] gfn_to_memslot+0xd5/0xe0 [kvm]
 [<ffffffffa03807d3>] __gfn_to_pfn+0x33/0x60 [kvm]
 [<ffffffffa0380885>] gfn_to_page+0x25/0x90 [kvm]
 [<ffffffffa038aeec>] kvm_vcpu_reload_apic_access_page+0x3c/0x80 [kvm]
 [<ffffffffa08f0a9c>] vmx_vcpu_reset+0x20c/0x460 [kvm_intel]
 [<ffffffffa039ab8e>] kvm_vcpu_reset+0x15e/0x1b0 [kvm]
 [<ffffffffa039ac0c>] kvm_arch_vcpu_setup+0x2c/0x50 [kvm]
 [<ffffffffa037f7e0>] kvm_vm_ioctl+0x1d0/0x780 [kvm]
 [<ffffffff810bc664>] ? __lock_is_held+0x54/0x80
 [<ffffffff812231f0>] do_vfs_ioctl+0x300/0x520
 [<ffffffff8122ee45>] ? __fget+0x5/0x250
 [<ffffffff8122f0fa>] ? __fget_light+0x2a/0xe0
 [<ffffffff81223491>] SyS_ioctl+0x81/0xa0
 [<ffffffff816fed6d>] system_call_fastpath+0x16/0x1b
Reported-by: NTakashi Iwai <tiwai@suse.de>
Reported-by: NAlexei Starovoitov <alexei.starovoitov@gmail.com>
Reviewed-by: NWanpeng Li <wanpeng.li@linux.intel.com>
Tested-by: NWanpeng Li <wanpeng.li@linux.intel.com>
Fixes: 38b99173Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>