Provide an interval after the end of DAPM sequencing so that we
can distinguish between a pop in the final step of the sequence
and a pop generated from some other source outside DAPM.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We need to set the widget power state we want to implement.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure that the audio subsystem is powered down cleanly when the system
shuts down by providing a shutdown operation. This ensures that all the
components have been returned to an off state cleanly which should avoid
audio issues from partially charged capacitors or noise on digital inputs
if the system is restarted quickly.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: NBen Dooks <ben-linux@fluff.org>

They are now only accessed within dapm_power_widgets() so can be local
to that function.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Handle gain ramping for PGAs so we can coalesce their power updates too.
This is not ideal since we can't cope properly with gain ramping for
stereo paths but that was the case without coalescing and gain ramping
is relatively infrequently used so the effects are limited.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The more flexible value muxes and named mixers don't need to be sorted
differently from a power management point of view, they are different
only in terms of the control interface and not in terms of seqencing
behaviour.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reduce the number of register writes we need to set the power state for
a CODEC by coalescing updates to widgets with the same sequence order and
same register into a single write.

This can be a noticable performance improvement with slow or heavily
contended control buses, such as I2C controllers with a low clock
frequency, and is particularly noticable when resuming. It can also
reduce the noticability of and pops and clicks by ensuring that left
and right channels are powered simultaneously if they are in the same
register.

Currently widgets that have events are not coalesced, including PGAs
which may use the volume ramping control.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Replace the remaining unsigned shorts with unsigned ints.
Tested with pcap2 codec (25 bits registers).
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Lump the list walk into a single function, and pull in the power
application too so we can do some further refactoring. Pure code
motion.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In the past the DAPM power sequencing was done by iterating over the list
of widgets once for each widget type and powering widgets of that type.
Instead of doing that do the sorting at the time we insert the widgets
into the lists of widgets to apply power changes to. This reduces the
amount of computation required for seqencing still further, though the
costs are generally dwarfed by the costs of the register writes
implementing them.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

A standard way of making sure we know when the bias level changes.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Rather than managing the bias level of the system based on if there is
an active audio stream manage it based on there being an active DAPM
widget. This simplifies the code a little, moving the power handling
into one place, and improves audio performance for bypass paths when no
playbacks or captures are active.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

sysfs is so standard these days there's no point.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

DAPM has always applied any changes to the power state of widgets as soon
as it has determined that they are required. Instead of doing this store
all the changes that are required on lists of widgets to power up and
down, then iterate over those lists and apply the changes. This changes
the sequence in which changes are implemented, doing all power downs
before power ups and always using the up/down sequences (previously they
were only used when changes were due to DAC/ADC power events). The error
handling is also changed so that we continue attempting to power widgets
if some changes fail.

The main benefit of this is to allow future changes to do optimisations
over the whole power sequence and to reduce the number of walks of the
widget graph required to check the power status of widgets.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Many modern CODECs have shared resources on chip which must be enabled
for portions of the chip to work but which can be disabled at other times
in order to achieve power savings. Examples of such resources include
power supplies and some internal clocks.

Since these widgets are dependencies for the audio path but do not carry
audio signals they require slightly different handling to most widgets -
they do not contribute to the audio path and so should not be counted as
either inputs or outputs during path walks.

Cases where one supply provides a supply for another will require
additional work. There is also room for more optimisation of the graph
walking to avoid repeated checks for the same thing.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Rather than having switch statements at point of use make the DAPM
power check a member of the widget structure and set it when we
instantiate the widget.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This also switches us to using a switch statement for the widget type
in dapm_power_widget().
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This will form a basis for further power check refactoring: the overall
goal of these changes is to allow us to check power separately to
applying it, allowing improvements in the power sequencing algorithms.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is simple code motion, intended to support future refactoring of
the DAPM algorithms and (more immediately) the additon of events for
DACs and ADCs.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

snd_soc_dapm_switch ends up ends up in dapm_new_mixer() (since a switch
is a special case of a mixer with only one input) but this wasn't
correctly handled in the code.

Also fix the coding style for the switch below while we're here.
Reported-by: NJoonyoung Shim <dofmind@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Essentially simple code motion to facilitate refactoring of the power
decisions.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

On some systems it is desirable for control for DAPM pins to be provided
to user space. This is the case with things like GSM modems which are
controlled primarily from user space, for example. Provide a helper which
exposes the state of a DAPM pin to user space for use in cases like this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is a further stage on the road to refactoring away the ASoC
platform device.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Modify the check for the mux type to also handle the
snd_soc_dapm_value_mux type in a same way as the snd_soc_dapm_mux.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Merge the recently introduced soc_value_enum structure to the soc_enum.
The value based enums are still handled separately from the normal enum types,
but with the merge some of the newly introduced functions can be removed.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch allows you to define the mixer paths as having the same name as the
paths they represent.

This is required to support codecs such as the wm9705 neatly without extra
controls in the alsa mixer.
Signed-off-by: NIan Molton <ian@mnementh.co.uk>

This patch introduces a new enum type.
In this enum type each enumerated items referred with a value.

This new enum type can handle enums encoded in bitfield, or any other
weird ways. twl4030 codec has several mux selection register, where the
input/output mux is coded in a bitfield. With the normal enum type this type
of mux can not be handled in a clean way.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Almost all parameters that have been misnamed in the comments.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This should never happen and it's helpful to identify the specific control
that failed when it does happen.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

One of the issues with the ASoC v1 API which has been addressed in the
ASoC v2 work that Liam Girdwood has done is that the ALSA card provided
by ASoC is distributed around the ASoC structures. For example, machine
wide data such as the struct snd_card are maintained as part of the
CODEC data structure, preventing the use of multiple codecs. This has
been addressed by refactoring the data structures so that all the data
for the ALSA card is contained in a single structure snd_soc_card which
replaces the existing snd_soc_machine and snd_soc_device.

Begin the process of backporting this by renaming struct snd_soc_machine
to struct snd_soc_card, better reflecting its function and bringing it
closer to standard ALSA terminology.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Call device_create_file only once in snd_soc_dapm_sys_add function.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

sound/soc/soc-dapm.c: In function 'snd_soc_dapm_sys_add':
sound/soc/soc-dapm.c:828: error: 'ret' undeclared (first use in this function)
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

As well as ensuring that UI-relevant parts of control names don't get
truncated in the DAPM code this avoids conflicts in long control names
that differ only at the end of a long string.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

i.e. echo 6 59 >/sys/kernel/debug/soc-audio.0/codec_reg
will set register 0x06 to a value of 0x59.
Also, pop_time debugfs interface setup is moved so that it
is setup in the same function as codec_reg
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

debugfs_create_dir() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: NZhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>