Firmware can signal whether the host driver may sent packets for
a specific destination or interface. This can happen when a
destination is sleeping or when going off-channel.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware provides the driver with credits used to transmit packets
to the firmware. When credits run out the packets should be queued
and dequeued when receiving creditback signals from the firmware.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The low-level sdio code has a large number of trace and info messages
that are mostly useful looking into bus specific issues. For tracing
higher-level driver functions it is better to have a dedicated level
for low-level sdio debugging.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Change-Id: Ia424ff18d9033b97aeffc248358e50c51805e815
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/74Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enabling the tx status signalling, which requires packet tagging
before sending to the firmware and handling the tx status signal.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware can signal the driver to allocate descriptor info for a given
mac address, which will be used for flow control and host queueing.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware and host can exchange signals which are carried within
the data packets. These are TLV based signals that are inserted
before the actual data, ie. ethernet frame.

This commit adds the new source module for this feature and enables
RSSI signals from firmware.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Inspired by tracing functionality added by Seth Forshee in the
brcmsmac driver, this patch adds similar functionality to brcmfmac.
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CDC debug is partly done with TRACE and partly with CTL, however
CDC hardly ever needs debugging. Use dedicated level CDC and
replace TRACE and CTL in dhd_cdc with that.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Several source files (but not all) define the pr_fmt() macro in exactly
the same way. Instead this commit defines it in a header file so driver
logging is consistent.

Cc: Joe Perches <joe@perches.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The source file wl_cfg80211.c has its own debug macros and levels.
This patch maps the macros to the ones used in the rest of the
brcmfmac driver.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The call to brcmf_dbg(ERROR, ...) only resulted in a log message
when compiled with -DDEBUG. Error messages are valuable for resolving
issues so this patch replaces it with brcmf_err(...) so they always
end up in the log.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add USB log level and update and add log messages in usb module.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

e-scan has become the default scanning method. This patch removes
the i-scan related code and cleans up e-scan related code to be
always enabled.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Refactor the functions that are related to getting and setting
data to and and from the firmware.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some events result in printing of the buffer when debug is
enabled. This printing was not very efficient. Changed to
macro so it comes out nice and clean without filling log buffer.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The structure brcmf_sdio contains a number of counters that are useful
for debugging. These were not available in user-space. This patch
exposes them in debugfs under the filename 'counters'.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds debugfs support to brcmfmac. It provide helper functions
to setup the debugfs folder structure for the driver, which has following
hierarchy:

<debugfs_mount>/brcmfmac/<dev_name>/

ie.: /sys/kernel/debug/brcmfmac/mmc0:0001:2/

The new source file provides functions to create and remove the two
folders and a function to retrieve the device-specific folder so files
can be created in it.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reduce the number of #ifdef DEBUG uses by
adding a dbg_hex_dump routine which has the
appropriate #ifdef DEBUG test.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow dynamic debugging.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Current CONFIG_BRCMDBG flag when enabled does not
necessarily enable proper pr_debug output when
DEBUG is not also enabled.

Remove BCMDBG define and just use DEBUG instead.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Debug message level macros are used for debug purpose. It would be
more appropriate to place them at dhd_dbg.h.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the brcm80211 tree to drivers/net/wireless, and disable the version that's
in drivers/staging.  This version includes the sources currently in staging,
plus any changes that have been sent out for review.

Sources in staging will be deleted in a followup patch.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert multiple BRCMF_<debug_level> macros to a single
brcmf_dbg(level, fmt, ...) macro.

Remove the now unnecessary double parentheses in the uses
of the old macros when converting to brcmf_dbg.

Delete all uses of "%s: [fmt]", __func__, args... and move
the "%s: ", __func__ to the macro for consistency.

Coalesce long formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The header file dhd_dbg.h contains several macros used throughout
the code starting with DHD_. These have been renamed to get rid
of this broadcom specific acronym.
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

DHD is a Broadcom internal term and has been replaced by BRCMF.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

cleanup of some unused macros.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The definitions in dhd.h have been renamed with consistent prefix
BRCMF_.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The common Makefile for both brcm80211 drivers defines the macro
BCMDBG upon select Kconfig item BRCMDBG. The fullmac source add
another macro DHD_DEBUG with the same meaning. This is removed
and all conditional code now checks for BCMDBG definition.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The naming convention of the drivers is to be made consistent. This
commit fixes the function in dhd_common.c and use the new names from
the calling code.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Code cleanup. These header files were emptied by the previous patch.
Signed-off-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver contained several calls to printf which was mapped
to printk using a macro. These have been changed to explicit
call to printk or use an appropropriate macro.
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NBrett Rudley <brudley@broadcom.com>
Reviewed-by: NHenry Ptasinski <henryp@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch to the existing bcm80211 directory in the staging tree adds fullmac
driver support for the BCM4329 SDIO chip from Broadcom.  Configuration of the
mac80211 driver or the fullmac driver can be done through menuconfig.
Signed-off-by: NHenry Ptasinski <henryp@broadcom.com>
Signed-off-by: NNohee Ko <noheek@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>