Jens found the following crash/regression:

[    0.000000] found SMP MP-table at [ffff8800000fdd80] fdd80
[    0.000000] Kernel panic - not syncing: Overlapping early reservations 12-f011 MP-table mpc to 0-fff BIOS data page

and

[    0.000000] Kernel panic - not syncing: Overlapping early reservations 12-f011 MP-table mpc to 6000-7fff TRAMPOLINE

and bisected it to b24c2a92 ("x86: Move find_smp_config()
earlier and avoid bootmem usage").

It turns out the BIOS is using the first 64k for mptable,
without reserving it.

So try to find good range for the real-mode trampoline instead of
hard coding it, in case some bios tries to use that range for sth.
Reported-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Tested-by: NJens Axboe <jens.axboe@oracle.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <4B21630A.6000308@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

As reported in

	http://bugzilla.kernel.org/show_bug.cgi?id=13940

on some system when acpi are enabled, acpi clears some BAR for some
devices without reason, and kernel will need to allocate devices for
them.  It then apparently hits some undocumented resource conflict,
resulting in non-working devices.

Try to increase alignment to get more safe range for unassigned devices.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since alloc_bootmem() will never return inaccessible (via virtual
addressing) memory anyway, using the ..._low() variant only makes sense
when the physical address range of the allocated memory must fulfill
further constraints, espacially since on 64-bits (or more generally in all
cases where the pools the two variants allocate from are than the full
available range.

Probably the use in alloc_tce_table() could also be eliminated (based on
code inspection of pci-calgary_64.c), but that seems too risky given I
know nothing about that hardware and have no way to test it.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

memory_setup is overridden by x86_quirks and by paravirts with weak
functions and quirks. Unify the whole mess and make it an
unconditional x86_init_ops function which defaults to the standard
function and can be overridden by the early platform code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Better to be paranoid against unpredicted nr_map modifications.
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <20090824175551.146070377@openvz.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Commit 5fd29d6c ("printk: clean up
handling of log-levels and newlines") changed printk semantics.  printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.

<level> is now included in the output on each additional use.

Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

fix hang with HIGHMEM_64G and 32bit resource.  According to hpa and
Linus, use (resource_size_t)-1 to fend off big ranges.

Analyzed by hpa
Reported-and-tested-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that the e820 code explicitly reserves 'potentially dangerous'
free physical memory address space to protect ACPI stolen RAM,
there's no need for the rounding quirk in the PCI allocator anymore.

Also, this quirk was open-ended iteration that could end up reserving
a lot of free space and potentially breaking drivers - such as the one
reported by Yannick Roehlly <yannick.roehlly@free.fr> where there's
a PCI device with a large memory resource.

So remove it.

[ Impact: make more of the PCI hole available for assigning pci devices ]
Reported-by: NYannick Roehlly <yannick.roehlly@free.fr>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NJesse Barnes <jesse.barnes@intel.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A01A7C8.5090701@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The point is to take all RAM resources we have, and
_after_ we've added all the resources we've seen in
the E820 tree, we then _also_ try to add fake reserved
entries for any "round up to X" at the end of the RAM
resources.

[ Impact: improve PCI mem-resource allocation robustness, protect "stolen RAM" ]
Reported-by: NYannick Roehlly <yannick.roehlly@free.fr>
Acked-by: NJesse Barnes <jesse.barnes@intel.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: yannick.roehlly@free.fr
LKML-Reference: <4A01A784.2050407@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

If the first non-reserved (sub-)range doesn't fit the size requested,
an endless loop will be entered. If a range returned from
find_e820_area_size() turns out insufficient in size, the range must
be skipped before calling the function again.

[ Impact: fixes boot hang on some platforms ]
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Impact: cleanup

This fixed various signedness issues in setup.c and e820.c:
arch/x86/kernel/setup.c:455:53: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/setup.c:455:53:    expected int *pnr_map
arch/x86/kernel/setup.c:455:53:    got unsigned int extern [toplevel] *<noident>
arch/x86/kernel/setup.c:639:53: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/setup.c:639:53:    expected int *pnr_map
arch/x86/kernel/setup.c:639:53:    got unsigned int extern [toplevel] *<noident>
arch/x86/kernel/setup.c:820:54: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/setup.c:820:54:    expected int *pnr_map
arch/x86/kernel/setup.c:820:54:    got unsigned int extern [toplevel] *<noident>

arch/x86/kernel/e820.c:670:53: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/e820.c:670:53:    expected int *pnr_map
arch/x86/kernel/e820.c:670:53:    got unsigned int [toplevel] *<noident>
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>

Impact: help debug e820 bugs

Try to print out more info, to catch wrong call parameters.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
LKML-Reference: <49BCB557.3030000@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: enhance e820 code to handle more cases

Try to handle new range which could be covered by one entry.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: jbeulich@novell.com
LKML-Reference: <49B9F0C1.10402@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: fix left range size on head

| commit 5c0e6f03
|    x86: fix code paths used by update_mptable
|    Impact: fix crashes under Xen due to unrobust e820 code

fixes one e820 bug, but introduces another bug.

Need to update size for left range at first in case it is header.

also add __e820_add_region take more parameter.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: jbeulich@novell.com
LKML-Reference: <49B9E286.502@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: fix crashes under Xen due to unrobust e820 code

find_e820_area_size() must return a properly distinguishable and
out-of-bounds value when it fails, and -1UL does not meet that
criteria on i386/PAE. Additionally, callers of the function must
check against that value.

early_reserve_e820() should be prepared for the region found to be
outside of the addressable range on 32-bits.

e820_update_range_map() should not blindly update e820, but should do
all it work on the map it got a pointer passed for (which in 50% of the
cases is &e820_saved). It must also not call e820_add_region(), as that
again acts on e820 unconditionally.

The issues were found when trying to make this option work in our Xen
kernel (i.e. where some of the silent assumptions made in the code
would not hold).
Signed-off-by: NJan Beulich <jbeulich@novell.com>
LKML-Reference: <49B9171B.76E4.0078.0@novell.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: cleanup

one 32-bit system reports:

BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001c000000 (usable)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
DMI 2.0 present.
last_pfn = 0x1c000 max_arch_pfn = 0x100000
kernel direct mapping tables up to 1c000000 @ 7000-c000
..
RAMDISK: 1bc69000 - 1bfef4fa
..
0MB HIGHMEM available.
448MB LOWMEM available.
  mapped low ram: 0 - 1c000000
  low ram: 00000000 - 1c000000
  bootmap 00002000 - 00005800
(9 early reservations) ==> bootmem [0000000000 - 001c000000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0000400000 - 00009ed14c]    TEXT DATA BSS ==> [0000400000 - 00009ed14c]
  #4 [001bc69000 - 001bfef4fa]          RAMDISK ==> [001bc69000 - 001bfef4fa]
  #5 [00009ee000 - 00009f2000]    INIT_PG_TABLE ==> [00009ee000 - 00009f2000]
  #6 [000009f400 - 0000100000]    BIOS reserved ==> [000009f400 - 0000100000]
  #7 [0000007000 - 0000007000]          PGTABLE
  #8 [0000002000 - 0000006000]          BOOTMAP ==> [0000002000 - 0000006000]

Notice the strange blank PGTABLE entry.

The reason is init_pg_table is big enough, and zero range is called
with init_memory_mapping/reserve_early().

So try to check the range in reserve_early()

v2: fix the reversed compare
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: nickpiggin@yahoo.com.au
Cc: ink@jurassic.park.msu.ru
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Introduce new initcall for marking the ACPI NVS memory at startup, so
that it can be saved/restored during hibernation/resume.

Based on a patch by Zhang Rui.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

Impact: fix trampoline sizing bug, save space

While debugging a suspend-to-RAM related issue it occured to me that
if the trampoline code had grown past 4 KB, we would have been
allocating too little memory for it, since the 4 KB size of the
trampoline is hardcoded into arch/x86/kernel/e820.c .  Change that
by making the kernel compute the trampoline size and allocate as much
memory as necessary.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This makes the late e820 resources use 'insert_resource_expand_to_fit()'
instead of doing a 'reserve_region_with_split()', and also avoids
marking them as IORESOURCE_BUSY.

This results in us being perfectly happy to use pre-existing PCI
resources even if they were marked as being in a reserved region, while
still avoiding any _new_ allocations in the reserved regions.  It also
makes for a simpler and more accurate resource tree.

Example resource allocation from Jonathan Corbet, who has firmware that
has an e820 reserved entry that covered a big range (e0000000-fed003ff),
and that had various PCI resources in it set up by firmware.

With old kernels, the reserved range would force us to re-allocate all
pre-existing PCI resources, and his reserved range would end up looking
like this:

	e0000000-fed003ff : reserved
	  fec00000-fec00fff : IOAPIC 0
	  fed00000-fed003ff : HPET 0

where only the pre-allocated special regions (IOAPIC and HPET) were kept
around.

With 2.6.28-rc2, which uses 'reserve_region_with_split()', Jonathan's
resource tree looked like this:

	e0000000-fe7fffff : reserved
	fe800000-fe8fffff : PCI Bus 0000:01
	 fe800000-fe8fffff : reserved
	fe900000-fe9d9aff : reserved
	fe9d9b00-fe9d9bff : 0000:00:1f.3
	 fe9d9b00-fe9d9bff : reserved
	fe9d9c00-fe9d9fff : 0000:00:1a.7
	 fe9d9c00-fe9d9fff : reserved
	fe9da000-fe9dafff : 0000:00:03.3
	 fe9da000-fe9dafff : reserved
	fe9db000-fe9dbfff : 0000:00:19.0
	 fe9db000-fe9dbfff : reserved
	fe9dc000-fe9dffff : 0000:00:1b.0
	 fe9dc000-fe9dffff : reserved
	fe9e0000-fe9fffff : 0000:00:19.0
	 fe9e0000-fe9fffff : reserved
	fea00000-fea7ffff : 0000:00:02.0
	 fea00000-fea7ffff : reserved
	fea80000-feafffff : 0000:00:02.1
	 fea80000-feafffff : reserved
	feb00000-febfffff : 0000:00:02.0
	 feb00000-febfffff : reserved
	fec00000-fed003ff : reserved
	 fec00000-fec00fff : IOAPIC 0
	 fed00000-fed003ff : HPET 0

and because the reserved entry had been split and moved into the
individual resources, and because it used the IORESOURCE_BUSY flag, the
drivers that actually wanted to _use_ those resources couldn't actually
attach to them:

	e1000e 0000:00:19.0: BAR 0: can't reserve mem region [0xfe9e0000-0xfe9fffff]
	HDA Intel 0000:00:1b.0: BAR 0: can't reserve mem region [0xfe9dc000-0xfe9dffff]

with this patch, the resource tree instead becomes

	e0000000-fed003ff : reserved
	  fe800000-fe8fffff : PCI Bus 0000:01
	  fe9d9b00-fe9d9bff : 0000:00:1f.3
	  fe9d9c00-fe9d9fff : 0000:00:1a.7
	    fe9d9c00-fe9d9fff : ehci_hcd
	  fe9da000-fe9dafff : 0000:00:03.3
	  fe9db000-fe9dbfff : 0000:00:19.0
	    fe9db000-fe9dbfff : e1000e
	  fe9dc000-fe9dffff : 0000:00:1b.0
	    fe9dc000-fe9dffff : ICH HD audio
	  fe9e0000-fe9fffff : 0000:00:19.0
	    fe9e0000-fe9fffff : e1000e
	  fea00000-fea7ffff : 0000:00:02.0
	  fea80000-feafffff : 0000:00:02.1
	  feb00000-febfffff : 0000:00:02.0
	  fec00000-fec00fff : IOAPIC 0
	  fed00000-fed003ff : HPET 0

ie the one reserved region now ends up surrounding all the PCI resources
that were allocated inside of it by firmware, and because it is not
marked BUSY, drivers have no problem attaching to the pre-allocated
resources.
Reported-and-tested-by: NJonathan Corbet <corbet@lwn.net>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There's no good reason why a resource_size_t shouldn't just be a
physical address, so simply redefine it in terms of phys_addr_t.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

When using kdump modifying the e820 map is yielding strange results.

For example starting with

 BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000100 - 0000000000093400 (usable)
 BIOS-e820: 0000000000093400 - 00000000000a0000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fee0000 (usable)
 BIOS-e820: 000000003fee0000 - 000000003fef3000 (ACPI data)
 BIOS-e820: 000000003fef3000 - 000000003ff80000 (ACPI NVS)
 BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)

and booting with args

memmap=exactmap memmap=640K@0K memmap=5228K@16384K memmap=125188K@22252K memmap=76K#1047424K memmap=564K#1047500K

resulted in:

 user-defined physical RAM map:
 user: 0000000000000000 - 0000000000093400 (usable)
 user: 0000000000093400 - 00000000000a0000 (reserved)
 user: 0000000000100000 - 000000003fee0000 (usable)
 user: 000000003fee0000 - 000000003fef3000 (ACPI data)
 user: 000000003fef3000 - 000000003ff80000 (ACPI NVS)
 user: 000000003ff80000 - 0000000040000000 (reserved)
 user: 00000000e0000000 - 00000000f0000000 (reserved)
 user: 00000000fec00000 - 00000000fec10000 (reserved)
 user: 00000000fee00000 - 00000000fee01000 (reserved)
 user: 00000000ff000000 - 0000000100000000 (reserved)

But should have resulted in:

 user-defined physical RAM map:
 user: 0000000000000000 - 00000000000a0000 (usable)
 user: 0000000001000000 - 000000000151b000 (usable)
 user: 00000000015bb000 - 0000000008ffc000 (usable)
 user: 000000003fee0000 - 000000003ff80000 (ACPI data)

This is happening because of an improper usage of strcmp() in the
e820 parsing code.  The strcmp() always returns !0 and never resets the
value for e820.nr_map and returns an incorrect user-defined map.

This patch fixes the problem.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

try to insert_resource second time, by expanding the resource...

for case: e820 reserved entry is partially overlapped with bar res...

hope it will never happen
Signed-off-by: NIngo Molnar <mingo@elte.hu>

this one replaces:

| commit a2bd7274
| Author: Yinghai Lu <yhlu.kernel@gmail.com>
| Date:   Mon Aug 25 00:56:08 2008 -0700
|
|    x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against BAR, v3

v2: insert e820 reserve resources before pnp_system_init
v3: fix merging problem in tip/x86/core
v4: address Linus's review about comments and condition in _late()
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

so could let BAR res register at first, or even pnp.

v2: insert e820 reserve resources before pnp_system_init
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Add support for the E820_UNUSABLE memory type, which is defined in
Revision 3.0b (Oct.  10, 2006) of the ACPI Specification on p.  394 Table
14-1:

  AddressRangeUnusuable This range of address contains memory in which
  errors have been detected.  This range must not be used by the OSPM.
Signed-off-by: NJoseph Cihula <joseph.cihula@intel.com>
Signed-off-by: NShane Wang <shane.wang@intel.com>
Signed-off-by: NGang Wei <gang.wei@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

introduce x86_quirks array of boot-time quirk methods.

No change in functionality intended.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

no user now
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

end_user_pfn used to modify the meaning of the e820 maps.

Now that all e820 operations are cleaned up, unified, tightened up,
the e820 map always get updated to reality, we don't need to keep
this secondary mechanism anymore.

If you hit this commit in bisection it means something slipped through.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

also let mem= to print out modified e820 map too
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Add early quirks support.

In preparation of enabling the generic architecture to boot on a VISWS.

This will allow us to remove the VISWS subarch and all its complications.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

even on 64bit systems with less than 4G RAM, we can now use fixmap
to handle acpi SIT near end of ram.

change e820_end to e820_end_of_ram again?
or e820_ram_pfn?
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NCyrill Gorcunov <gorcunov@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: akpm@linux-foundation.org
Cc: andi@firstfloor.org
Signed-off-by: NIngo Molnar <mingo@elte.hu>

to avoid warning from find_low_pfn_range for high pages size etc
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

When system have 4g less ram installed, and acpi table sit
near end of ram, make max_pfn cover them too,
so 64bit kernel don't need to mess up fixmap.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Cc: "Suresh Siddha" <suresh.b.siddha@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

so when it is called after early_param, e820_saved get updated too.
esp for mpc update.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

so other path that will override memory_setup or
machine_specific_memory_setup could have e820_saved too.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This patch uses the /sys/firmware/memmap interface provided in the last patch
on the x86 architecture when E820 is used. The patch copies the E820
memory map very early, and registers the E820 map afterwards via
firmware_map_add_early().
Signed-off-by: NBernhard Walle <bwalle@suse.de>
Acked-by: NGreg KH <gregkh@suse.de>
Acked-by: NVivek Goyal <vgoyal@redhat.com>
Cc: kexec@lists.infradead.org
Cc: yhlu.kernel@gmail.com
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>