The Tegra30 EHCI controller is mostly compatible with the Tegra20
controller, except Tegra30 includes the HOSTPC register extension.
The has_hostpc capability bit must be set in the ehci_hcd structure if
the controller has such extensions. The new tegra_ehci_soc_config
structure is added to describe the differences between the SoCs.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The Tegra30 TRM recommends configuration of certain PHY parameters for
optimal quality. Program the following registers based on device tree
parameters:

- UTMIP_XCVR_HSSLEW: HS slew rate control.
- UTMIP_HSSQUELCH_LEVEL: HS squelch detector level
- UTMIP_HSDISCON_LEVEL: HS disconnect detector level.

These registers exist in Tegra20, but programming them hasn't been
necessary, so these parameters won't be set on Tegra20 to keep the
device trees backward compatible.

Additionally, the UTMIP_XCVR_SETUP parameter can be set from fuses
instead of a software-programmed value, as the optimal value can
vary between invidual boards. The boolean property
nvidia,xcvr-setup-use-fuses can be used to enable this behaviour.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Document the new device tree parameters for Tegra30 USB PHY.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The Tegra30 USB PHY is a bit different than the Tegra20 PHY:

- The EHCI controller supports the HOSTPC register extension, and some
  of the fields that the PHY needs to modify (PHCD and PTS) have moved
  to the new HOSTPC register.
- Some of the UTMI PLL configuration registers have moved from the USB
  register space to the Clock-And-Reset controller space. In Tegra30
  the clock driver is responsible for configuring the UTMI PLL.
- The USBMODE register must be explicitly written to enter host mode.
- Certain PHY parameters need to be programmed for optimal signal
  quality. Support for this will be added in the next patch.

The new tegra_phy_soc_config structure is added to describe the
differences between the SoCs.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some of the PHY parameters are not set according to the TRMs:

- UTMIP_FS_PREABMLE_J should be set, not cleared
- UTMIP_XCVR_LSBIAS_SEL should be cleared, not set
- UTMIP_PD_CHRG should be set in host mode and cleared in device mode
- UTMIP_XCVR_SETUP is a two-part field; the upper bits were not set
  properly
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The has_hostpc capability bit indicates that the host controller has the
HOSTPC register extensions, but at the same time enables clock disabling
power saving features with the PHY Low Power Clock Disable (PHCD) bit.

However, some host controllers have the HOSTPC extensions but don't
support the low-power feature, so the PHCD bit must not be set on those
controllers. Add a separate capability bit for the low-power feature
instead, and change all existing users of has_hostpc to use this new
capability bit.

The idea for this commit is taken from an old 2012 commit that never got
merged ("disociate chipidea PHY low power suspend control from hostpc")
Inspired-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The binding spec wasn't clear that the order of the phandles in the
usb-phy array has meaning.  Clarify this point in the binding that
it should be <USB2-HS-PHY, USB3-SS-PHY>.
Signed-off-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The conversion to videobuf2 failed to check the return value of
vb2_qbuf(). Fix it.

Cc: stable@vger.kernel.org
Reported-by: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This driver is currently used by musb' cppi41 couter part. I may merge
both dma engine user of musb at some point but not just yet.

The driver seems to work in RX/TX mode in host mode, tested on mass
storage. I increaed the size of the TX / RX transfers and waited for the
core code to cancel a transfers and it seems to recover.

v2..3:
- use mall transfers on RX side and check data toggle.
- use rndis mode on tx side so we haveon interrupt for 4096 transfers.
- remove custom "transferred" hack and use dmaengine_tx_status() to
  compute the total amount of data that has been transferred.
- cancel transfers and reclaim descriptors

v1..v2:
- RX path added
- dma mode 0 & 1 is working
- device tree nodes re-created.

Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This moves the two instances from the big node into two child nodes. The
glue layer ontop does almost nothing.

There is one devices containing the control module for USB (2) phy,
(2) usb and later the dma engine. The usb device is the "glue device"
which contains the musb device as a child. This is what we do ever since.

The new file musb_am335x is just here to prob the new bus and populate
child devices.

There are a lot of changes to the dsps file as a result of the changes:

- musb_core_offset
  This is gone. The device tree provides memory ressources information
  for the device there is no need to "fix" things

- instances
  This is gone as well. If we have two instances then we have have two
  child enabled nodes in the device tree. For instance the SoC in beagle
  bone has two USB instances but only one has been wired up so there is
  no need to load and init the second instance since it won't be used.

- dsps_glue is now per glue device
  In the past there was one of this structs but with an array of two and
  each instance accessed its variable depending on the platform device
  id.

- no unneeded copy of structs
  I do not know why struct dsps_musb_wrapper is copied but it is not
  necessary. The same goes for musb_hdrc_platform_data which allocated
  on demand and then again by platform_device_add_data(). One copy is
  enough.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

dsps uses a nop driver which is added in dsps itself and does the PHY
on/off calls within dsps. Since those calls are now moved the nop driver
itself, we can now request the phy proper phy and remove those calls.
Currently only the first musb interface is used so we only add one phy
node for now.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This driver is a redo of my earlier attempt. It uses parts of the
generic PHY driver and uses the new control driver for the register
the phy needs to power on/off the phy. It also enables easy access for
the wakeup register which is not yet implemented.
The difference between the omap attempt is:
- no static holding variable
- one global visible function which exports a struct with callbacks to
  access the "control" registers.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch exports the mostly generic functions so they can be used from
other phy driver instead of duplicating the code.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NFelipe Balbi <balbi@ti.com>

Conflicts:
	drivers/usb/phy/phy-generic.c

The "nop" driver isn't a do-nothing-stub but supports a couple functions
like clock on/off or is able to use a voltage regulator. This patch
simply renames the driver to "generic" since it is easy possible to
extend it by a simple function istead of writing a complete driver.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When platform_driver_probe() is not used, bind/unbind via sysfs
is enabled.  Thus, __exit_p annotation should be removed from
remove().

Also, mv_otg_remove() is staticized, because this function is
used only in this file. Fix the following sparse warning:

drivers/usb/phy/phy-mv-usb.c:656:5: warning: symbol 'mv_otg_remove' was not declared. Should it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

mv_u3d_phy_shutdown() is used only in this file.
Fix the following sparse warning:

drivers/usb/phy/phy-mv-u3d-usb.c:85:6: warning: symbol 'mv_u3d_phy_shutdown' was not declared. Should it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

control_selector_init() is used only in this file.
audio_bind_config() is used only in audio.c file to which
f_uac1.c is included. Thus, these functions are staticized
to fix the following warnings.

drivers/usb/gadget/f_uac1.c:698:12: warning: symbol 'control_selector_init' was not declared. Should it be static?
drivers/usb/gadget/f_uac1.c:722:12: warning: symbol 'audio_bind_config' was not declared. Should it be static?
Acked-by: NJassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added __user annotation to fix the following sparse warning.

drivers/usb/gadget/u_uac1.c:194:52: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/gadget/u_uac1.c:194:52:    expected void const [noderef] <asn:1>*buf
drivers/usb/gadget/u_uac1.c:194:52:    got void *buf
Acked-by: NJassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

rndis_init() and rndis_exit() are used only in this file.
Fix the following sparse warnings:

drivers/usb/gadget/rndis.c:1145:5: warning: symbol 'rndis_init' was not declared. Should it be static?
drivers/usb/gadget/rndis.c:1179:6: warning: symbol 'rndis_exit' was not declared. Should it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The local variables such as 'filename', 'vendor_name', and
'product_name' are pointers; thus, use NULL instead of 0 to fix
the following sparse warnings

drivers/usb/gadget/f_mass_storage.c:3046:27: warning: Using plain integer as NULL pointer
drivers/usb/gadget/f_mass_storage.c:3050:28: warning: Using plain integer as NULL pointer
drivers/usb/gadget/f_mass_storage.c:3051:29: warning: Using plain integer as NULL pointer
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As far as prep_dma() is called with spinlock held,
we have to pass GFP_ATOMIC regardless of gfp argument.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The AT91 PMC (Power Management Controller) provides an USB clock used by
USB Full Speed host (ohci) and USB Full Speed device (udc).
The usb drivers (ohci and udc) must configure this clock to 48Mhz.
This configuration was formely done in mach-at91/clock.c, but this
implementation will be removed when moving to common clk framework.

This patch adds support for usb clock retrieval and configuration, and is
backward compatible with the current at91 clk implementation (if usb clk
is not found, it does not configure/enable it).
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds missing clk_put on fclk and iclk in case the probe function
fails after these clocks have been retrieved.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fusb300_rdcxf() used only in this file.
Fix the following sparse warning:

drivers/usb/gadget/fusb300_udc.c:560:6: warning: symbol 'fusb300_rdcxf' was not declared. Should it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

'req' is a pointer; thus, use NULL instead of 0
to fix the following sparse warning:

drivers/usb/gadget/goku_udc.c:775:13: warning: Using plain integer as NULL pointer
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled. Unnecessary CONFIG_PM ifdefs
are removed.

drivers/usb/dwc3/dwc3-pci.c:215:12: warning: 'dwc3_pci_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-pci.c:224:12: warning: 'dwc3_pci_resume' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the wrapper function for retrieving the
platform_data instead of accessing dev->platform_data
directly.

While at that also make change 'node' initialization
to use the dev pointer.
Inspired-by: NJingoo Han  <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The device tree binding documentation for tegra20-usb-phy used to claim
that the vbus-supply property is required for host phys and optional
for otg phys. This should be the other way around.
Signed-off-by: NMikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit 052a11d1 (usb: phy: make PHY driver selection
possible by controller drivers) changed the rules
on how drivers/usb/phy/of.c would be compiled and
failed to update include/linux/usb/of.h accordingly.

Because of that, we can fall into situations where
of_usb_get_phy_mode() is redefined. In order to fix
the error, we update the IS_ENABLED() check in
include/linux/usb/of.h to reflect the condition
where of.c is built.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When deferred probe happens driver will try to ioremap multiple times
and will fail. Memory resource.start variable is a global variable,
modifications in this field will be accumulated on every probe.
Fix this by moving the above operations after driver hold all
required PHY's.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use switch() instead of if-else when checking for the PHY type.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The EOI register is not present in the AM335x memory space according to
the TRM and thus removed.
Should any platform using the EOI register get merged then it may be
used again if the register address is not zero.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The ti81xx platform is not fully supported right now. This patch renames
the date structure to a am33xx prefix which is actually used.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the new of_usb_get_dr_mode helper function for parsing dr_mode
from the device tree. Also replace the usage of the custom
tegra_usb_phy_mode enum with the standard enum.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the new of_usb_get_phy_mode helper function for parsing phy_type
from the device tree.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>