Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 19 11月, 2008 3 次提交
    • S
      ftrace: fix dyn ftrace filter selection · 32464779
      由 Steven Rostedt 提交于 
      Impact: clean up and fix for dyn ftrace filter selection

The previous logic of the dynamic ftrace selection of enabling
or disabling functions was complex and incorrect. This patch simplifies
the code and corrects the usage. This simplification also makes the
code more robust.

Here is the correct logic:

  Given a function that can be traced by dynamic ftrace:

  If the function is not to be traced, disable it if it was enabled.
  (this is if the function is in the set_ftrace_notrace file)

  (filter is on if there exists any functions in set_ftrace_filter file)

  If the filter is on, and we are enabling functions:
    If the function is in set_ftrace_filter, enable it if it is not
      already enabled.
    If the function is not in set_ftrace_filter, disable it if it is not
      already disabled.

  Otherwise, if the filter is off and we are enabling function tracing:
    Enable the function if it is not already enabled.

  Otherwise, if we are disabling function tracing:
    Disable the function if it is not already disabled.

This code now sets or clears the ENABLED flag in the record, and at the
end it will enable the function if the flag is set, or disable the function
if the flag is cleared.

The parameters for the function that does the above logic is also
simplified. Instead of passing in confusing "new" and "old" where
they might be swapped if the "enabled" flag is not set. The old logic
even had one of the above always NULL and had to be filled in. The new
logic simply passes in one parameter called "nop". A "call" is calculated
in the code, and at the end of the logic, when we know we need to either
disable or enable the function, we can then use the "nop" and "call"
properly.

This code is more robust than the previous version.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      32464779
    • S
      ftrace: make filtered functions effective on setting · 82043278
      由 Steven Rostedt 提交于 
      Impact: fix filter selection to apply when set

It can be confusing when the set_filter_functions is set (or cleared)
and the functions being recorded by the dynamic tracer does not
match.

This patch causes the code to be updated if the function tracer is
enabled and the filter is changed.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      82043278
    • S
      ftrace: fix set_ftrace_filter · f10ed36e
      由 Steven Rostedt 提交于 
      Impact: fix of output of set_ftrace_filter

The commit "ftrace: do not show freed records in
             available_filter_functions"

Removed a bit too much from the set_ftrace_filter code, where we now see
all functions in the set_ftrace_filter file even when we set a filter.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      f10ed36e
  3. 16 11月, 2008 2 次提交
    • A
      Fix inotify watch removal/umount races · 8f7b0ba1
      由 Al Viro 提交于 
      Inotify watch removals suck violently.

To kick the watch out we need (in this order) inode->inotify_mutex and
ih->mutex.  That's fine if we have a hold on inode; however, for all
other cases we need to make damn sure we don't race with umount.  We can
*NOT* just grab a reference to a watch - inotify_unmount_inodes() will
happily sail past it and we'll end with reference to inode potentially
outliving its superblock.

Ideally we just want to grab an active reference to superblock if we
can; that will make sure we won't go into inotify_umount_inodes() until
we are done.  Cleanup is just deactivate_super().

However, that leaves a messy case - what if we *are* racing with
umount() and active references to superblock can't be acquired anymore?
We can bump ->s_count, grab ->s_umount, which will almost certainly wait
until the superblock is shut down and the watch in question is pining
for fjords.  That's fine, but there is a problem - we might have hit the
window between ->s_active getting to 0 / ->s_count - below S_BIAS (i.e.
the moment when superblock is past the point of no return and is heading
for shutdown) and the moment when deactivate_super() acquires
->s_umount.

We could just do drop_super() yield() and retry, but that's rather
antisocial and this stuff is luser-triggerable.  OTOH, having grabbed
->s_umount and having found that we'd got there first (i.e.  that
->s_root is non-NULL) we know that we won't race with
inotify_umount_inodes().

So we could grab a reference to watch and do the rest as above, just
with drop_super() instead of deactivate_super(), right? Wrong.  We had
to drop ih->mutex before we could grab ->s_umount.  So the watch
could've been gone already.

That still can be dealt with - we need to save watch->wd, do idr_find()
and compare its result with our pointer.  If they match, we either have
the damn thing still alive or we'd lost not one but two races at once,
the watch had been killed and a new one got created with the same ->wd
at the same address.  That couldn't have happened in inotify_destroy(),
but inotify_rm_wd() could run into that.  Still, "new one got created"
is not a problem - we have every right to kill it or leave it alone,
whatever's more convenient.

So we can use idr_find(...) == watch && watch->inode->i_sb == sb as
"grab it and kill it" check.  If it's been our original watch, we are
fine, if it's a newcomer - nevermind, just pretend that we'd won the
race and kill the fscker anyway; we are safe since we know that its
superblock won't be going away.

And yes, this is far beyond mere "not very pretty"; so's the entire
concept of inotify to start with.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      8f7b0ba1
    • L
      Move "exit_robust_list" into mm_release() · 8141c7f3
      由 Linus Torvalds 提交于 
      We don't want to get rid of the futexes just at exit() time, we want to
drop them when doing an execve() too, since that gets rid of the
previous VM image too.

Doing it at mm_release() time means that we automatically always do it
when we disassociate a VM map from the task.

Reported-by: pageexec@freemail.hu
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Alex Efros <powerman@powerman.name>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      8141c7f3
  5. 13 11月, 2008 5 次提交
  7. 12 11月, 2008 2 次提交
  9. 11 11月, 2008 7 次提交
    • P
      sched: release buddies on yield · 2002c695
      由 Peter Zijlstra 提交于 
      Clear buddies on yield, so that the buddy rules don't schedule them
despite them being placed right-most.

This fixed a performance regression with yield-happy binary JVMs.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Tested-by: NLin Ming <ming.m.lin@intel.com>
      2002c695
    • G
      timers: handle HRTIMER_CB_IRQSAFE_UNLOCKED correctly from softirq context · 5d5254f0
      由 Gautham R Shenoy 提交于 
      Impact: fix incorrect locking triggered during hotplug-intense stress-tests

While migrating the the CB_IRQSAFE_UNLOCKED timers during a cpu-offline,
we queue them on the cb_pending list, so that they won't go
stale.

Thus, when the callbacks of the timers run from the softirq context,
they could run into potential deadlocks, since these callbacks
assume that they're running with irq's disabled, thereby annoying
lockdep!

Fix this by emulating hardirq context while running these callbacks from
the hrtimer softirq.

=================================
[ INFO: inconsistent lock state ]
2.6.27 #2
--------------------------------
inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.
ksoftirqd/0/4 [HC0[0]:SC1[1]:HE1:SE0] takes:
 (&rq->lock){++..}, at: [<c011db84>] sched_rt_period_timer+0x9e/0x1fc
{in-hardirq-W} state was registered at:
  [<c014103c>] __lock_acquire+0x549/0x121e
  [<c0107890>] native_sched_clock+0x88/0x99
  [<c013aa12>] clocksource_get_next+0x39/0x3f
  [<c0139abc>] update_wall_time+0x616/0x7df
  [<c0141d6b>] lock_acquire+0x5a/0x74
  [<c0121724>] scheduler_tick+0x3a/0x18d
  [<c047ed45>] _spin_lock+0x1c/0x45
  [<c0121724>] scheduler_tick+0x3a/0x18d
  [<c0121724>] scheduler_tick+0x3a/0x18d
  [<c012c436>] update_process_times+0x3a/0x44
  [<c013c044>] tick_periodic+0x63/0x6d
  [<c013c062>] tick_handle_periodic+0x14/0x5e
  [<c010568c>] timer_interrupt+0x44/0x4a
  [<c0150c9f>] handle_IRQ_event+0x13/0x3d
  [<c0151c14>] handle_level_irq+0x79/0xbd
  [<c0105634>] do_IRQ+0x69/0x7d
  [<c01041e4>] common_interrupt+0x28/0x30
  [<c047007b>] aac_probe_one+0x1a3/0x3f3
  [<c047ec2d>] _spin_unlock_irqrestore+0x36/0x39
  [<c01512b4>] setup_irq+0x1be/0x1f9
  [<c065d70b>] start_kernel+0x259/0x2c5
  [<ffffffff>] 0xffffffff
irq event stamp: 50102
hardirqs last  enabled at (50102): [<c047ebf4>] _spin_unlock_irq+0x20/0x23
hardirqs last disabled at (50101): [<c047edc2>] _spin_lock_irq+0xa/0x4b
softirqs last  enabled at (50088): [<c0128ba6>] do_softirq+0x37/0x4d
softirqs last disabled at (50099): [<c0128ba6>] do_softirq+0x37/0x4d

other info that might help us debug this:
no locks held by ksoftirqd/0/4.

stack backtrace:
Pid: 4, comm: ksoftirqd/0 Not tainted 2.6.27 #2
 [<c013f6cb>] print_usage_bug+0x13e/0x147
 [<c013fef5>] mark_lock+0x493/0x797
 [<c01410b1>] __lock_acquire+0x5be/0x121e
 [<c0141d6b>] lock_acquire+0x5a/0x74
 [<c011db84>] sched_rt_period_timer+0x9e/0x1fc
 [<c047ed45>] _spin_lock+0x1c/0x45
 [<c011db84>] sched_rt_period_timer+0x9e/0x1fc
 [<c011db84>] sched_rt_period_timer+0x9e/0x1fc
 [<c01210fd>] finish_task_switch+0x41/0xbd
 [<c0107890>] native_sched_clock+0x88/0x99
 [<c011dae6>] sched_rt_period_timer+0x0/0x1fc
 [<c0136dda>] run_hrtimer_pending+0x54/0xe5
 [<c011dae6>] sched_rt_period_timer+0x0/0x1fc
 [<c0128afb>] __do_softirq+0x7b/0xef
 [<c0128ba6>] do_softirq+0x37/0x4d
 [<c0128c12>] ksoftirqd+0x56/0xc5
 [<c0128bbc>] ksoftirqd+0x0/0xc5
 [<c0134649>] kthread+0x38/0x5d
 [<c0134611>] kthread+0x0/0x5d
 [<c0104477>] kernel_thread_helper+0x7/0x10
 =======================
Signed-off-by: NGautham R Shenoy <ego@in.ibm.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: N"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      5d5254f0
    • O
      fix for account_group_exec_runtime(), make sure ->signal can't be freed under rq->lock · ad474cac
      由 Oleg Nesterov 提交于 
      Impact: fix hang/crash on ia64 under high load

This is ugly, but the simplest patch by far.

Unlike other similar routines, account_group_exec_runtime() could be
called "implicitly" from within scheduler after exit_notify(). This
means we can race with the parent doing release_task(), we can't just
check ->signal != NULL.

Change __exit_signal() to do spin_unlock_wait(&task_rq(tsk)->lock)
before __cleanup_signal() to make sure ->signal can't be freed under
task_rq(tsk)->lock. Note that task_rq_unlock_wait() doesn't care
about the case when tsk changes cpu/rq under us, this should be OK.

Thanks to Ingo who nacked my previous buggy patch.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Reported-by: NDoug Chapman <doug.chapman@hp.com>
      ad474cac
    • S
      ring-buffer: prevent infinite looping on time stamping · 4143c5cb
      由 Steven Rostedt 提交于 
      Impact: removal of unnecessary looping

The lockless part of the ring buffer allows for reentry into the code
from interrupts. A timestamp is taken, a test is preformed and if it
detects that an interrupt occurred that did tracing, it tries again.

The problem arises if the timestamp code itself causes a trace.
The detection will detect this and loop again. The difference between
this and an interrupt doing tracing, is that this will fail every time,
and cause an infinite loop.

Currently, we test if the loop happens 1000 times, and if so, it will
produce a warning and disable the ring buffer.

The problem with this approach is that it makes it difficult to perform
some types of tracing (tracing the timestamp code itself).

Each trace entry has a delta timestamp from the previous entry.
If a trace entry is reserved but and interrupt occurs and traces before
the previous entry is commited, the delta timestamp for that entry will
be zero. This actually makes sense in terms of tracing, because the
interrupt entry happened before the preempted entry was commited, so
one may consider the two happening at the same time. The order is
still preserved in the buffer.

With this idea, instead of trying to get a new timestamp if an interrupt
made it in between the timestamp and the test, the entry could simply
make the delta zero and continue. This will prevent interrupts or
tracers in the timer code from causing the above loop.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
      4143c5cb
    • S
      ftrace: disable tracing on resize · bf5e6519
      由 Steven Rostedt 提交于 
      Impact: fix for bug on resize

This patch addresses the bug found here:

 http://bugzilla.kernel.org/show_bug.cgi?id=11996

When ftrace converted to the new unified trace buffer, the resizing of
the buffer was not protected as much as it was originally. If tracing
is performed while the resize occurs, then the buffer can be corrupted.

This patch disables all ftrace buffer modifications before a resize
takes place.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
      bf5e6519
    • T
      nohz: disable tick_nohz_kick_tick() for now · ae99286b
      由 Thomas Gleixner 提交于 
      Impact: nohz powersavings and wakeup regression

commit fb02fbc1 (NOHZ: restart tick
device from irq_enter()) causes a serious wakeup regression.

While the patch is correct it does not take into account that spurious
wakeups happen on x86. A fix for this issue is available, but we just
revert to the .27 behaviour and let long running softirqs screw
themself.

Disable it for now.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
      ae99286b
    • T
      irq: call __irq_enter() before calling the tick_idle_check · ee5f80a9
      由 Thomas Gleixner 提交于 
      Impact: avoid spurious ksoftirqd wakeups

The tick idle check which is called from irq_enter() was run before
the call to __irq_enter() which did not set the in_interrupt() bits in
preempt_count. That way the raise of a softirq woke up softirqd for
nothing as the softirq was handled on return from interrupt.

Call __irq_enter() before calling into the tick idle check code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      ee5f80a9
  11. 10 11月, 2008 1 次提交
  13. 07 11月, 2008 3 次提交
  15. 06 11月, 2008 3 次提交
    • R
      cpumask: introduce new API, without changing anything · 2d3854a3
      由 Rusty Russell 提交于 
      Impact: introduce new APIs

We want to deprecate cpumasks on the stack, as we are headed for
gynormous numbers of CPUs.  Eventually, we want to head towards an
undefined 'struct cpumask' so they can never be declared on stack.

1) New cpumask functions which take pointers instead of copies.
   (cpus_* -> cpumask_*)

2) Several new helpers to reduce requirements for temporary cpumasks
   (cpumask_first_and, cpumask_next_and, cpumask_any_and)

3) Helpers for declaring cpumasks on or offstack for large NR_CPUS
   (cpumask_var_t, alloc_cpumask_var and free_cpumask_var)

4) 'struct cpumask' for explicitness and to mark new-style code.

5) Make iterator functions stop at nr_cpu_ids (a runtime constant),
   not NR_CPUS for time efficiency and for smaller dynamic allocations
   in future.

6) cpumask_copy() so we can allocate less than a full cpumask eventually
   (for alloc_cpumask_var), and so we can eliminate the 'struct cpumask'
   definition eventually.

7) work_on_cpu() helper for doing task on a CPU, rather than saving old
   cpumask for current thread and manipulating it.

8) smp_call_function_many() which is smp_call_function_mask() except
   taking a cpumask pointer.

Note that this patch simply introduces the new functions and leaves
the obsolescent ones in place.  This is to simplify the transition
patches.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      2d3854a3
    • A
      Add round_jiffies_up and related routines · 9c133c46
      由 Alan Stern 提交于 
      This patch (as1158b) adds round_jiffies_up() and friends.  These
routines work like the analogous round_jiffies() functions, except
that they will never round down.

The new routines will be useful for timeouts where we don't care
exactly when the timer expires, provided it doesn't expire too soon.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
      9c133c46
    • S
      generic-ipi: fix the smp_mb() placement · 561920a0
      由 Suresh Siddha 提交于 
      smp_mb() is needed (to make the memory operations visible globally) before
sending the ipi on the sender and the receiver (on Alpha atleast) needs
smp_read_barrier_depends() in the handler before reading the call_single_queue
list in a lock-free fashion.

On x86, x2apic mode register accesses for sending IPI's don't have serializing
semantics. So the need for smp_mb() before sending the IPI becomes more
critical in x2apic mode.

Remove the unnecessary smp_mb() in csd_flag_wait(), as the presence of that
smp_mb() doesn't mean anything on the sender, when the ipi receiver is not
doing any thing special (like memory fence) after clearing the CSD_FLAG_WAIT.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
      561920a0
  17. 05 11月, 2008 5 次提交
  19. 03 11月, 2008 3 次提交
  21. 02 11月, 2008 2 次提交
  23. 31 10月, 2008 4 次提交