Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now that clock delay settings for 8 bit DDR are correct, and vqmmc
support is available, we can enable MMC_CAP_1_8V_DDR support. This
enables MMC HS-DDR at up to 52 MHz, even if signal voltage switching
is not available.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Allwinner's MMC controller needs to run at double the card clock rate
for 8 bit DDR transfer modes. Interestingly, this is not needed for
4 bit DDR transfers.

Different clock delays are needed for 8 bit eMMC DDR, due to the
increased module clock rate. For the A80 though, the same values for
4 bit and 8 bit are shared. The new values for the other SoCs were from
A83T user manual's "new timing mode" default values, which describes
them in clock phase, rather than delay periods. These values were used
without any modification. They may not be correct, but they work.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

DDR transfer modes include UHS-1 DDR50 and MMC HS-DDR (or MMC_DDR52).
Consider MMC_DDR52 when setting clock delays.

Since MMC high speed mode goes up to 52 MHz instead of 50 MHz for SD,
and this number is visible in the capability macro, increase the
clock rate upper limit to 52 MHz.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The bus width is sometimes the actual bus width, and sometimes indices
to different arrays encoding the bus width. In my debugging case "2"
could mean 8-bit as well as 4-bit, which was extremly confusing. Let's
use the human-readable actual bus width in all places.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In linux/mmc/host.h, mmc_card_is_removable() is already defined.
There is no reason that it doesn't use.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The sdhci_iproc_remove() is jsut a wrapper to sdhci_pltfm_unregister.
So use the sdhci_pltfm_unregister() for the .remove hook directly.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Acked-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since sdhci-iproc can support bcm2835 we need add the
compatible string to the binding.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NScott Branden <sbranden@broadcom.com>
Acked-by: NEric Anholt <eric@anholt.net>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NScott Branden <sbranden@broadcom.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Scott Branden from Broadcom said that the BCM2835 eMMC IP core is
very similar to IPROC and share most of the quirks. So use this driver
instead of separate one.

The sdhci-iproc contains a better workaround for the clock domain
crossing problem which doesn't need any delays. This results in a
better write performance.

Btw we get the rid of the SDHCI_CAPABILITIES hack in the sdhci_readl
function.
Suggested-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NEric Anholt <eric@anholt.net>
Acked-by: NScott Branden <sbranden@broadcom.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch moves the definition of the MMC capabilities
from the probe function into iproc platform data. After
that we are able to add support for another platform more
easily.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Suggested-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NScott Branden <sbranden@broadcom.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

I had to use the source to determine what I need to write to 'test' so
that all tests are run. Let's mention this explicitly in 'testlist'.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

I don't see a reason why a host driver should depend on the card driver.
It also prevents that we can use the mmc_test driver. So, remove it.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

IMO this info is only useful for developers. Most users won't need this
information, since there is not much they can do about it.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When DT based probing is used but the DMA request fails, the
driver will print uninitialized stack data from the rx_req
and tx_req variables, as indicated by this warning:

drivers/mmc/host/omap_hsmmc.c: In function 'omap_hsmmc_probe':
drivers/mmc/host/omap_hsmmc.c:2162:3: warning: 'rx_req' may be used uninitialized in this function [-Wmaybe-uninitialized]
   dev_err(mmc_dev(host->mmc), "unable to obtain RX DMA engine channel %u\n", rx_req);

This removes the DMA request line number from the warning, which
is the easiest solution and won't hurt us any more as we are
planning to remove the legacy code path anyway.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch enables sdhci-acpi devices to suspend/resume asynchronously.
This will improve system suspend/resume speed. After enabling the
sdhci-acpi devices and all their child devices to suspend/resume
asynchronously on ASUS T100TA, the system suspend-to-idle time is
reduced from 1645ms to 1089ms, and the system resume time is reduced
from 940ms to 908ms.
Signed-off-by: NZhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch enables mmc hosts to suspend/resume asynchronously.
This will improve system suspend/resume speed. After applying
this patch and enabling all mmc hosts' child devices to
suspend/resume asynchronously on ASUS T100TA, the system
suspend-to-idle time is reduced from 1645ms to 1107ms, and the
system resume time is reduced from 940ms to 914ms.
Signed-off-by: NZhonghui Fu <zhonghui.fu@linux.intel.com>
Acked-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

eMMC chips require 2 power supplies, vmmc for internal logic, and vqmmc
for driving output buffers. vqmmc also controls signaling voltage. Most
boards we've seen use the same regulator for both, nevertheless the 2
have different usages, and should be set separately.

This patch adds support for vqmmc regulator supply, including voltage
switching. The MMC core can use this to try different signaling voltages
for eMMC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Let .set_ios() fail if mmc_regulator_set_ocr() fails to enable and set a
proper voltage for vmmc.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sunxi_mmc_init_host() originated from Allwinner kernel sources. The
magic numbers written to various registers was never documented.

Add comments for values found in Allwinner user manuals.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The RPi firmware-based clocks driver can actually disable
unused clocks, so when switching to use it we ended up losing
our MMC clock once all devices were probed.

This patch adopts the changes from 1e5a0a9a ("mmc: sdhci-bcm2835:
Actually enable the clock") to sdhci-iproc.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Clock frequency values written to an mmc host should not be less than
the minimum clock frequency which the mmc host supports.
Signed-off-by: NYuan Juntao <juntaox.yuan@intel.com>
Signed-off-by: NPawel Wodkowski <pawelx.wodkowski@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adopts the changes from 475c9e43 ("mmc: sdhci-bcm2835:
Clean up platform allocations if sdhci init fails") to sdhci-iproc.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The Arason SD host controller supports set block count command (cmd23)
and high speed mode. This patch re-enable both of these features that
was disabled. For device that doesn't support high speed, it should
configure its capability register accordingly instead disables it
explicitly.
Signed-off-by: NRameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since v4.3+, CONFIG_REGULATOR_PBIAS should be enabled (for platforms that
have PBIAS regulator) in order for MMC1 to work.

Add a more verbose print to help enable CONFIG_REGULATOR_PBIAS for users
using a olddefconfig or a custom .config.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Variable assignment just before return is redundant.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Use to_delayed_work() instead of open-coding it.
Signed-off-by: NGeliang Tang <geliangtang@163.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Use to_delayed_work() instead of open-coding it.
Signed-off-by: NGeliang Tang <geliangtang@163.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This issue was detected by using the Coccinelle software.

Two pointer checks could be repeated by the sdricoh_init_mmc() function
during error handling even if the relevant properties can be determined
for the involved variables before by source code analysis.

* This implementation detail could be improved by adjustments
  for jump targets according to the Linux coding style convention.

* Drop an unnecessary initialisation for the variable "mmc" then.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

These variables will eventually be set to an appropriate value a bit later.
* host
* iobase
* result

Thus let us omit the explicit initialisation at the beginning.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Pull perf fixes from Thomas Gleixner:
 "A rather largish series of 12 patches addressing a maze of race
  conditions in the perf core code from Peter Zijlstra"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Robustify task_function_call()
  perf: Fix scaling vs. perf_install_in_context()
  perf: Fix scaling vs. perf_event_enable()
  perf: Fix scaling vs. perf_event_enable_on_exec()
  perf: Fix ctx time tracking by introducing EVENT_TIME
  perf: Cure event->pending_disable race
  perf: Fix race between event install and jump_labels
  perf: Fix cloning
  perf: Only update context time when active
  perf: Allow perf_release() with !event->ctx
  perf: Do not double free
  perf: Close install vs. exit race

Pull x86 fixes from Thomas Gleixner:
 "This update contains:

   - Hopefully the last ASM CLAC fixups

   - A fix for the Quark family related to the IMR lock which makes
     kexec work again

   - A off-by-one fix in the MPX code.  Ironic, isn't it?

   - A fix for X86_PAE which addresses once more an unsigned long vs
     phys_addr_t hickup"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mpx: Fix off-by-one comparison with nr_registers
  x86/mm: Fix slow_virt_to_phys() for X86_PAE again
  x86/entry/compat: Add missing CLAC to entry_INT80_32
  x86/entry/32: Add an ASM_CLAC to entry_SYSENTER_32
  x86/platform/intel/quark: Change the kernel's IMR lock bit to false

Pull scheduler fixlet from Thomas Gleixner:
 "A trivial printk typo fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Fix trivial typo in printk() message

Pull irq fixes from Thomas Gleixner:
 "Four small fixes for irqchip drivers:

   - Add missing low level irq handler initialization on mxs, so
     interrupts can acutally be delivered

   - Add a missing barrier to the GIC driver

   - Two fixes for the GIC-V3-ITS driver, addressing a double EOI write
     and a cache flush beyond the actual region"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3: Add missing barrier to 32bit version of gic_read_iar()
  irqchip/mxs: Add missing set_handle_irq()
  irqchip/gicv3-its: Avoid cache flush beyond ITS_BASERn memory size
  irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1

Pull staging/android fix from Greg KH:
 "Here is one patch, for the android binder driver, to resolve a
  reported problem.  Turns out it has been around for a while (since
  3.15), so it is good to finally get it resolved.

  It has been in linux-next for a while with no reported issues"

* tag 'staging-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE