- 08 6月, 2007 10 次提交
-
-
由 Herbert Xu 提交于
Previously once inetdev_init has been called on a device any changes made to ipv4_devconf_dflt would have no effect on that device's configuration. This creates a problem since we have moved the point where inetdev_init is called from when an address is added to where the device is registered. This patch is the first half of a set that tries to mimic the old behaviour while still calling inetdev_init. It propagates any changes to ipv4_devconf_dflt to those devices that have not had the corresponding attribute set. The next patch will forcibly set all values at the point where inetdev_init was previously called. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Herbert Xu 提交于
This patch converts the ipv4_devconf config members (everything except sysctl) to an array. This allows easier manipulation which will be needed later on to provide better management of default config values. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Herbert Xu 提交于
When I made the inetdev_init call work on all devices I incorrectly left in the panic call as well. It is obviously undesirable to panic on an allocation failure for a normal network device. This patch moves the panic call under the loopback if clause. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Patrick McHardy 提交于
A time_wait socket inherits sk_bound_dev_if from the original socket, but it is not used when sending ACK packets using ip_send_reply. Fix by passing the oif to ip_send_reply in struct ip_reply_arg and use it for output routing. Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Update to version 1.5.11. Signed-off-by: NMichael Chan <mchan@broadcom.com> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The statistics block DMA on 5708 can be messed up occasionally on the average of about once per hour. If the user is reading the counters within one second after the corruption, the counters will be all messed up. One second later, the counters will be ok again until the next corruption occurs. The workaround is to disable the periodic statistics DMA. Instead, we manually trigger the DMA once a second in bnx2_timer(). This manual trigger of the DMA avoids the problem. As a consequence, we can only allow 0 or 1 second settings for ethtool -C statistics block. Thanks to Jean-Daniel Pauget <jd@disjunkt.com> and CaT <cat@zip.com.au> for reporting this rare problem. Signed-off-by: NMichael Chan <mchan@broadcom.com> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add missing code to enable DMA on 5709 A1. The bit is a no-op on A0 and therefore can be set on all 5709 chips. Signed-off-by: NMichael Chan <mchan@broadcom.com> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
For correctness, we need to wait for the MEM_INIT bit to be cleared in the BNX2_CTX_COMMAND register before proceeding. [Added return -EBUSY when the MEM_INIT bit doesn't clear, suggested by Jeff Garzik.] Signed-off-by: NMichael Chan <mchan@broadcom.com> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
There's a bug in the driver that only initializes half of the context memory on the 5708. Surprisingly, this works most of the time except for some occasional netdev watchdogs when sending a lot of 64-byte packets. The fix is to add the missing code to initialize the 2nd halves of all context memory. Signed-off-by: NMichael Chan <mchan@broadcom.com> Acked-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Linus Torvalds 提交于
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: [VIDEO] sunxvr500fb: Fix pseudo_palette array size [VIDEO] sunxvr2500fb: Fix pseudo_palette array size [VIDEO] ffb: The pseudo_palette is only 16 elements long [VIDEO]: Fix section mismatch warning in promcon. [ATA]: Back out bogus (SPARC64 && !PCI) Kconfig depends. [SPARC64]: Fill in gaps in non-PCI dma_*() NOP implementation. [SPARC64]: Fix {mc,smt}_capable(). [SPARC64]: Make core and sibling groups equal on UltraSPARC-IV. [SPARC64]: Proper multi-core scheduling support. [SPARC64]: Provide mmu statistics via sysfs. [SPARC64]: Fix service channel hypervisor function names. [SPARC64]: Export basic cpu properties via sysfs. [SPARC64]: Move topology init code into new file, sysfs.c
-
- 07 6月, 2007 18 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc由 Linus Torvalds 提交于
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: [POWERPC] Fix building of COFF zImages [POWERPC] spufs: Fix error handling in spufs_fill_dir() [POWERPC] Add table of contents to booting-without-of.txt [POWERPC] spufs: Don't yield nosched context [POWERPC] Fix typo in booting-without-of-txt section numbering [POWERPC] scc_sio: Fix link failure [POWERPC] cbe_cpufreq: Limit frequency via cpufreq notifier chain [POWERPC] Fix pci_setup_phb_io_dynamic for pci_iomap [POWERPC] spufs scheduler: Fix wakeup races [POWERPC] spufs: Synchronize pte invalidation vs ps close [POWERPC] spufs: Free mm if spufs_fill_dir() failed [POWERPC] spufs: Fix gang destroy leaks [POWERPC] spufs: Hook up spufs_release_mem [POWERPC] spufs: Refuse to load the module when not running on cell [POWERPC] pasemi: Fix iommu + 64K PAGE_SIZE bug
-
由 Roland McGrath 提交于
This patch should get a few birds. It prevents sigaction calls from clearing TIF_SIGPENDING in other threads, which could leak -ERESTART*. And It fixes ptrace_stop not to clear it, which done at the syscall exit stop could leak -ERESTART*. It probably removes the harm from signalfd, at least assuming it never calls dequeue_signal on kernel threads that might have used block_all_signals. Signed-off-by: NRoland McGrath <roland@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andy Whitcroft 提交于
scripts/checkpatch.pl should be executable, make it so. Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Acked-by: NAndrew Morton <akpm@linux-foundation.org> Acked-by: NJoel Schopp <jschopp@austin.ibm.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Paul Mackerras 提交于
The COFF zImage (for booting oldworld powermacs) wasn't being built correctly because the procedure descriptor in crt0.S for the zImage entry point wasn't declared as .globl, and therefore wasn't getting pulled in from wrapper.a by the linker. This adds the necessary .globl statement. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Sebastian Siewior 提交于
The error path in spufs_fill_dir() is broken. If d_alloc_name() or spufs_new_file() fails, spufs_prune_dir() is getting called. At this time dir->inode is not set and a NULL pointer is dereferenced by mutex_lock(). This bugfix replaces spufs_prune_dir() with a shorter version that does not touch dir->inode but simply removes all children. Signed-off-by: NSebastian Siewior <bigeasy@linux.vnet.ibm.com> Signed-off-by: NJeremy Kerr <jk@ozlabs.org> Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Stuart Yoder 提交于
Add table of contents. Signed-off-by: NStuart Yoder <stuart.yoder@freescale.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Christoph Hellwig 提交于
Nosched context sould never be scheduled out, thus we must not deactivate them in spu_yield ever. Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NJeremy Kerr <jk@ozlabs.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Stuart Yoder 提交于
Fix typo in section numbering. Signed-off-by: NStuart Yoder <stuart.yoder@freescale.com> Acked-by: NDavid Gibson <david@gibson.dropbear.id.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Christoph Hellwig 提交于
scc_sio.o should only be built if the txx9 serial driver is actually built into the kernel. Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> -- Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Thomas Renninger 提交于
... and get rid of cpufreq_set_policy call that caused a build failure due interfering commits. Signed-off-by: NThomas Renninger <trenn@suse.de> Signed-off-by: NChristian Krafft <krafft@de.ibm.com> Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Arnd Bergmann 提交于
We had a problem on a system with only dynamically allocated PCI buses (using of_pci_phb_driver) in combination with libata. This setup ended up having no "primary" phb, which means that pci_io_base never got initialized and all IO port numbers are 64 bit numbers, which is larger than the PIO_MASK limit. Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Christoph Hellwig 提交于
Fix the race between checking for contexts on the runqueue and actually waking them in spu_deactive and spu_yield. The guts of spu_reschedule are split into a new helper called grab_runnable_context which shows if there is a runnable thread below a specified priority and if yes removes if from the runqueue and uses it. This function is used by the new __spu_deactivate hepler shared by preemption and spu_yield to grab a new context before deactivating a specified priority and if yes removes if from the runqueue and uses it. This function is used by the new __spu_deactivate hepler shared by preemption and spu_yield to grab a new context before deactivating the old one. Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NJeremy Kerr <jk@ozlabs.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Christoph Hellwig 提交于
Make sure the mapping_lock also protects access to the various address_space pointers used for tearing down the ptes on a spu context switch. Because unmap_mapping_range can sleep we need to turn mapping_lock from a spinlock into a sleeping mutex. Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NJeremy Kerr <jk@ozlabs.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Sebastian Siewior 提交于
In case spufs_fill_dir() fails only put_spu_context() gets called for cleanup and the acquired mm_struct never gets freed. Signed-off-by: NSebastian Siewior <bigeasy@linux.vnet.ibm.com> Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NJeremy Kerr <jk@ozlabs.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Jeremy Kerr 提交于
Previously, closing a SPE gang that still has contexts would trigger a WARN_ON, and leak the allocated gang. This change fixes the problem by using the gang's reference counts to destroy the gang instead. The gangs will persist until their last reference (be it context or open file handle) is gone. Also, avoid using statements with side-effects in a WARN_ON(). Signed-off-by: NJeremy Kerr <jk@ozlabs.org> Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Christoph Hellwig 提交于
Currently spufs_mem_release and the mem file doesn't have any release method hooked up, leading to leaks everytime is used. Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NJeremy Kerr <jk@ozlabs.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Arnd Bergmann 提交于
As noticed by David Woodhouse, it's currently possible to mount spufs on any machine, which means that it actually will get mounted by fedora. This refuses to load the module on platforms that have no support for SPUs. Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NJeremy Kerr <jk@ozlabs.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Olof Johansson 提交于
The powerpc iommu code was refactored by Linas back in the 2.6.20 time frame to map 4K pages from the generic code, but I had forgotten to go back and fix my platform driver before submitting it. Signed-off-by: NOlof Johansson <olof@lixom.net> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 06 6月, 2007 3 次提交
-
-
由 Antonino Daplas 提交于
- the pseudo_palette is only 16 elements long. - the pseudo_palette has only 16 elements. Do not write if regno (the array index) is more than 15. Signed-off-by: NAntonino Daplas <adaplas@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Antonino Daplas 提交于
- the pseudo_palette is only 16 elements long. - the pseudo_palette has only 16 elements. Do not write if regno (the array index) is more than 15. Signed-off-by: NAntonino Daplas <adaplas@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Antonino Daplas 提交于
The pseudo_palette is only 16 elements long. Signed-off-by: NAntonino Daplas <adaplas@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 6月, 2007 9 次提交
-
-
由 Sam Ravnborg 提交于
Fix the following warnings in promcon: WARNING: o-sparc64/drivers/video/console/built-in.o(.text+0x480): Section mismatch: reference to .init.data:promfont_unitable (between 'promcon_init_unimap' and 'promcon_init') WARNING: o-sparc64/drivers/video/console/built-in.o(.text+0x488): Section mismatch: reference to .init.data:promfont_unitable (between 'promcon_init_unimap' and 'promcon_init') WARNING: o-sparc64/drivers/video/console/built-in.o(.text+0x48c): Section mismatch: reference to .init.data:promfont_unicount (between 'promcon_init_unimap' and 'promcon_init') WARNING: o-sparc64/drivers/video/console/built-in.o(.text+0x490): Section mismatch: reference to .init.data:promfont_unicount (between 'promcon_init_unimap' and 'promcon_init') The warnings happens because the function: promcon_init_unimap() references promfont_unitable and promfont_unicount which are marked __initdata by the conmakehash command in the drivers/video/console/Makefile Fix the warning by removing the __initdata marker on the two variables. Signed-off-by: NSam Ravnborg <sam@ravnborg.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
It's not just sun4v hypervisor platforms that should return true for this, sun4u with UltraSPARC-IV should return true too. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
The scheduling domain hierarchy is: all cpus --> cpus that share an instruction cache --> cpus that share an integer execution unit Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Miller 提交于
If the system supports hypervisor based statistics, allow them to be fetched, enabled, and disabled via sysfs. Enable and disable via the boolean: /sys/devices/systems/cpu/cpuN/mmustat_enable Statistic values are provided under: /sys/devices/systems/cpu/cpuN/mmu_status/ Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Miller 提交于
sed 's/scv/svc/' Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Cache sizes, udelay_val, and clock_tick. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-