Add MODULE_ALIAS() declerations for all the supported platform
devices for this driver.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The driver should be checking for a negative error code from
s3c2410_dma_request(), not non-zero. Newer kernels now return
the DMA channel number that was allocated by the request.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Add support to the S3C24XX MMC driver to have the card detect be on
a pin that is not IRQ capable.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Fix a crash if host->mrq->data is NULL on ending a transfer.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Support for inverting the sense of the MMC driver's write
protect detection line.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch adds platform data support to the s3mci driver.  This allows
flexible board-specific configuration of set_power, card detect and read only
pins.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Fix Bug #677 - I/O errors on heavy microSD writes for 2.6.22.x.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

is stopped.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NHarald Welte <laforge@openmoko.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Bugfix to ensure DMA channel allocated is freed on exit.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch is a workaround of some S3C2410 MMC chip bug
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This is the latest S3C MMC/SD driver by Thomas Kleffel
with cleanups as suggested by AKPM done by Ben Dooks.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NThomas Kleffel <tk@maintech.de>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Be a bit more robust and fall back to PIO if someone is feeding us
bogus addresses.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Clean up and reorganise the mmc_test driver so that it (hopefully)
is easier to extend with more complex tests.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Many failures are non-permanent, but the card might need some time to
finish what it is doing before becoming responsive again. Make sure we
wait for it to finish programming before dealing with the error.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Add support for the scatter-gather DMA mode present on newer controllers.
As the mode requires 32-bit alignment, non-aligned chunks are handled by
using a bounce buffer.

Also add some new quirks to handle controllers that have bugs in the
ADMA engine.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The upcoming JMicron chips will have solved all the currently known
bugs, so don't penalize them for older problems.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

We can only perform the tests on MMC and SD cards, so avoid binding
to any other type.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Make sure that the maximum size for a byte mode transfer is identical
in all places. Also tweak the transfer helper so that a single byte
mode transfer is preferred over (possibly multiple) block mode
request(s).
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

There are a lot of crappy controllers out there that cannot handle
all the request sizes that the MMC/SD/SDIO specifications require.
In case the card driver can pad the data to overcome the problems,
this commit adds a helper that calculates how much that padding
should be.

A corresponding helper is also added for SDIO, but it can also deal
with all the complexities of splitting up a large transfer efficiently.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The MMC core provides a carddetect poll feature, time to
remove the driver's own implementation of it.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Don't process an MMC request if no card is present.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Clean up the codebase, no functional changes.
- merge the au1xmmc.h header contents into the driver file,
- indentation, spelling and style fixes.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Wire up the SD controllers' SDIO IRQ capability.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Remove the DB1200 board-specific functions (card present, read-only,
activity LED methods) and instead add platform data which is passed
to the driver.  This also allows for platforms to implement other
carddetect schemes (e.g. dedicated irq) without having to pollute the
driver code.  The poll timer (used for pb1200) is kept for compatibility.

With the board-specific stuff gone, the driver's ->probe() code can be
cleaned up considerably.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The byte mode support fails to clear the byte mode bit in the command
register, possibly leaving byte mode enabled with the counters programmed
in non-byte mode.
Signed-off-by: NVille Syrjala <syrjala@sci.fi>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

According to the documentation the AT91SAM9261 MCI shares the block size
limitations of the AT91RM9200 MCI. Also the errata documentation for
AT91RM9200 and AT91SAM9261 state that stream commands are not supported.
This has not been tested on actual hardware.
Signed-off-by: NVille Syrjala <syrjala@sci.fi>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

AT91SAM926[0/3] PDC must write at least 12 bytes. The code compiles and runs
but the actual condition for this erratum did not trigger in my tests so it's
unclear if it actually works as intended.
Signed-off-by: NVille Syrjala <syrjala@sci.fi>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

In at91_mci_completed_command() function, this patch distinguishes
command error and data error. It reports it in the corresponding
error field.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Reading AT91_MCI_SR again at the end of transfer can corrupt the
error reporting. Some fields in the SR register are read-and-clear.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Enable SDIO interrupt handling.
Signed-off-by: NEric Benard <ebenard@free.fr>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

at91_mci is capable of multiwrite. Enable it before it disappears.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Modify bytes_xfered value after a write.

That will report, as accurately as possible, the amount of
sectors that are effectively written.

This update introduces the check of the busy signal given by
the card.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The at91 mci controller internal state machine seems to often crash. This can
be fixed by resetting the controller after each command for at91rm9200 and by
setting the MCI_BLKR register on at91sam926*.
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Signed-off-by: NHans J Koch <hjk@linutronix.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Detect command timeout (or mci controller hangs).
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Signed-off-by: NHans J Koch <hjk@linutronix.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Implement transfer with size not modulo 4 for at91sam9*. Please note that the
at91rm9200 simply can't handle this.
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Make the variable name in the comments match the actual name
of the variable.
Signed-off-by: NDeepak Saxena <dsaxena@laptop.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Now get_ro() callback must return 0/1 values for its logical states, and
negative errno values in case of error. If particular host instance doesn't
support RO/WP switch, it should return -ENOSYS.

This patch changes some hosts in two ways:

1. Now functions should be smart to not return negative values in
   "RO asserted" case (particularly gpio_ calls could return negative
   values for the outermost GPIOs).

   Also, board code usually passes get_ro() callbacks that directly return
   gpioreg & bit result, so at91_mci, imxmmc, pxamci and mmc_spi's get_ro()
   handlers need take special care when returning platform's values to the
   mmc core.

2. In case of host instance didn't implement get_ro() callback, it should
   really return -ENOSYS and let the mmc core decide what to do about it
   (mmc core thinks the same way as the hosts, so it isn't functional
   change).
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch adds new platform data variable "caps", so platforms
could pass theirs capabilities into MMC core (for example, platforms
without interrupt on the CD line will most probably want to pass
MMC_CAP_NEEDS_POLL).

New platform get_cd() callback provided to optimize polling.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>