Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:

leds-gpio leds.12: pins are not configured from the driver
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

mx28evk has a free slot U50 that can be used to populate an I2C EEPROM.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add LRADC support.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

mx28evk has a free slot (J89) which can be used to populate an SPI NOR Flash.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

hog_pins is used to setup the pin functions, and it is not neccesarily used only
for GPIO pins, so use only 'hog' to describe a more generic term.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

- add usb phy devices
- add usb controller devices
- add usb vbus regulators
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Tested-by: NSubodh Nijsure <snijsure@grid-net.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The presence and muxing of lcdif control pins can vary much on different
boards.  Move them into imx28-evk.dts to make lcdif_24bit_pins_a only
about data pins, so that it can be reused by other boards.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Only pins GPMI_CE0N and GPMI_READY0 are generally used by other boards.
Move GPMI_CE1N and GPMI_READY1 into imx28-evk.dts to make gpmi_pins_a
more general, and can be used by other boards.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add flexan devices for imx28-evk board.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add lcd support for imx23-evk and imx28-evk.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add pwm device and pwm-backlight for imx23-evk and imx28-evk.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add heartbeat gpio-leds for imx28-evk board.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add missing properties for fec, phy-supply, phy-reset-gpios and
phy-reset-duration, which are required by fec driver for successfully
probe fec from device tree, if bootloader hasn't set those things up.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add vmmc-supply for mmc device, so that the power to mmc slot can be
turned on by mmc driver if bootloader hasn't done it.

Also remove "okay" status for mmc1/ssp1, as the device has pin conflict
with gpmi-nand.  Actually the device is already disabled since the
mxs-mmc driver adopts pinctrl support because there is no pinctrl setup
for the device in dts.  Make this explicit by removing "okay" status.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Before gpio_request can directly ask pinctrl system to configure the
requested pin into gpio mode, we use "hog" entry (pinctrl state of
pin controller itself) to configure gpios.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add auart0 and auart3 support.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

add gpmi-nand device tree support.
add gpmi-nand pinctrl support.

Also enable the gpmi support for mx28-evk board.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch includes basic dt support which can boot via nfs rootfs.
Signed-off-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NMarek Vasut <marex@denx.de>