commit c744a65c
  md: don't set md arrays to readonly on shutdown.

removed the possibility of a 'BUG' when data is written to an array
that has just been switched to read-only, but also introduced the
possibility that the array metadata could be corrupted.

If, when md_notify_reboot gets the mddev lock, the array is
in a state where it is assembled but hasn't been started (as can
happen if the personality module is not available, or in other unusual
situations), then incorrect metadata will be written out making it
impossible to re-assemble the array.

So only call __md_stop_writes() if the array has actually been
activated.

This patch is needed for any stable kernel which has had the above
commit applied.

Cc: stable@vger.kernel.org
Reported-by: NChristoph Nelles <evilazrael@evilazrael.de>
Signed-off-by: NNeilBrown <neilb@suse.de>

Commit 7bfec5f3

   md/raid5: If there is a spare and a want_replacement device, start replacement.

cause md_check_recovery to call ->add_disk much more often.
Instead of only when the array is degraded, it is now called whenever
md_check_recovery finds anything useful to do, which includes
updating the metadata for clean<->dirty transition.
This causes unnecessary work, and causes info messages from ->add_disk
to be reported much too often.

So refine md_check_recovery to only do any actual recovery checking
(including ->add_disk) if MD_RECOVERY_NEEDED is set.

This fix is suitable for 3.3.y:

Cc: stable@vger.kernel.org
Reported-by: NJan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: NNeilBrown <neilb@suse.de>

Fix segfault caused by using rdev_for_each instead of rdev_for_each_safe

Commit dafb20fa mistakenly replaced a safe
iterator with an unsafe one when making some macro changes.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

If a bitmap is added while the array is active, it is possible
for bitmap_daemon_work to run while the bitmap is being
initialised.
This is particularly a problem if bitmap_daemon_work sees
bitmap->filemap as non-NULL before it has been filled in properly.
So hold bitmap_info.mutex while filling in ->filemap
to prevent problems.

This patch is suitable for any -stable kernel, though it might not
apply cleanly before about 3.1.

Cc: stable@vger.kernel.org
Signed-off-by: NNeilBrown <neilb@suse.de>

If r1bio->sectors % 8 != 0,then the memcmp and a later
memcpy will omit the last bio_vec.

This is suitable for any stable kernel since 3.1 when bad-block
management was introduced.

Cc: stable@vger.kernel.org
Signed-off-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

bitmap_new_disk_sb() would still create V3 bitmap superblock
with host-endian layout.

Perhaps I'm confused, but shouldn't bitmap_new_disk_sb() be
creating a V4 bitmap superblock instead, that is portable,
as per comment in bitmap.h?
Signed-off-by: NAndrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

When comparing two pages read from different legs of a mirror, only
compare the bytes that were read, not the whole page.

In most cases we read a whole page, but in some cases with
bad blocks or odd sizes devices we might read fewer than that.

This bug has been present "forever" but at worst it might cause
a report of two many mismatches and generate a little bit
extra resync IO, so there is no need to back-port to -stable
kernels.
Reported-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

When create a raid5 using assume-clean and echo check or repair to
sync_action.Then component disks did not operated IO but the raid
check/resync faster than normal.
Because the judgement in function analyse_stripe():
		if (do_recovery ||
		    sh->sector >= conf->mddev->recovery_cp)
			s->syncing = 1;
		else
			s->replacing = 1;
When check or repair,the recovery_cp == MaxSectore,so syncing equal zero
not one.

This bug was introduced by commit 9a3e1101
    md/raid5:  detect and handle replacements during recovery.
so this patch is suitable for 3.3-stable.

Cc: stable@vger.kernel.org
Signed-off-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Because rde->nr_pending > 0,so can not remove this disk.
And in any case, we aren't holding rcu_read_lock()
Signed-off-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

raid1 arrays do not have the notion of chunk size. Calculate the
largest chunk sector size we can use to avoid a divide by zero OOPS
when aligning the size of the new array to the chunk size.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

1/ We can only treat a known-bad-block like a read-error if we
   have the data that belongs in that block.  So fix that test.

2/ If we cannot recovery a stripe due to insufficient data,
   don't tell "md_done_sync" that the sync failed unless we really
   did fail something.  If we successfully record bad blocks,
   that is success.
Reported-by: N"majianpeng" <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Signed-off-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Signed-off-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Signed-off-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

This device-mapper target creates a read-only device that transparently
validates the data on one underlying device against a pre-generated tree
of cryptographic checksums stored on a second device.

Two checksum device formats are supported: version 0 which is already
shipping in Chromium OS and version 1 which incorporates some
improvements.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NMandeep Singh Baines <msb@chromium.org>
Signed-off-by: NWill Drewry <wad@chromium.org>
Signed-off-by: NElly Jones <ellyjones@chromium.org>
Cc: Milan Broz <mbroz@redhat.com>
Cc: Olof Johansson <olofj@chromium.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch introduces a new function dm_bufio_prefetch. It prefetches
the specified range of blocks into dm-bufio cache without waiting
for i/o completion.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Add dm thin target arguments to control discard support.

ignore_discard: Disables discard support

no_discard_passdown: Don't pass discards down to the underlying data
device, but just remove the mapping within the thin provisioning target.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Support discards in the thin target.

On discard the corresponding mapping(s) are removed from the thin
device.  If the associated block(s) are no longer shared the discard
is passed to the underlying device.

All bios other than discards now have an associated deferred_entry
that is saved to the 'all_io_entry' in endio_hook.  When non-discard
IO completes and associated mappings are quiesced any discards that
were deferred, via ds_add_work() in process_discard(), will be queued
for processing by the worker thread.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

drivers/md/dm-thin.c |  173 ++++++++++++++++++++++++++++++++++++++++++++++----
 drivers/md/dm-thin.c |  172 ++++++++++++++++++++++++++++++++++++++++++++++-----
 1 file changed, 158 insertions(+), 14 deletions(-)

This patch contains the ground work needed for dm-thin to support discard.

  - Adds endio function that replaces shared_read_endio.

  - Introduce an explicit 'quiesced' flag into the new_mapping structure.
    Before, this was implicitly indicated by m->list being empty.

  - The map_info->ptr remains constant for the duration of a bio's trip
    through the thin target.  Make it easier to reason about it.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Use dm_target_offset wrapper instead of referencing the awkward ti->begin
explicitly.
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Support the use of an external _read only_ device as an origin for a thin
device.

Any read to an unprovisioned area of the thin device will be passed
through to the origin.  Writes trigger allocation of new blocks as
usual.

One possible use case for this would be VM hosts that want to run
guests on thinly-provisioned volumes but have the base image on another
device (possibly shared between many VMs).
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The thin metadata format can only make use of a device that is <=
THIN_METADATA_MAX_SECTORS (currently 15.9375 GB).  Therefore, there is no
practical benefit to using a larger device.

However, it may be that other factors impose a certain granularity for
the space that is allocated to a device (E.g. lvm2 can impose a coarse
granularity through the use of large, >= 1 GB, physical extents).

Rather than reject a larger metadata device, during thin-pool device
construction, switch to allowing it but issue a warning if a device
larger than THIN_METADATA_MAX_SECTORS_WARNING (16 GB) is
provided.  Any space over 15.9375 GB will not be used.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Save space by removing entries from the space map ref_count tree if
they're no longer needed.

Ref counts are stored in two places: a bitmap if the ref_count is
below 3, or a btree of uint32_t if 3 or above.

When a ref_count that was above 3 drops below we can remove it from
the tree and save some metadata space.  This removal was commented out
before because I was unsure why this was causing under-populated btree
nodes.  Earlier patches have fixed this issue.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Commit unwritten data every second to prevent too much building up.

Released blocks don't become available until after the next commit
(for crash resilience).  Prior to this patch commits were only
triggered by a message to the target or a REQ_{FLUSH,FUA} bio.  This
allowed far too big a position to build up.

The interval is hard-coded to 1 second.  This is a sensible setting.
I'm not making this user configurable, since there isn't much to be
gained by tweaking this - and a lot lost by setting it far too high.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Device mapper uses sscanf to convert arguments to numbers. The problem is that
the way we use it ignores additional unmatched characters in the scanned string.

For example, this `if (sscanf(string, "%d", &number) == 1)' will match a number,
but also it will match number with some garbage appended, like "123abc".

As a result, device mapper accepts garbage after some numbers. For example
the command `dmsetup create vg1-new --table "0 16384 linear 254:1bla 34816bla"'
will pass without an error.

This patch fixes all sscanf uses in device mapper. It appends "%c" with
a pointer to a dummy character variable to every sscanf statement.

The construct `if (sscanf(string, "%d%c", &number, &dummy) == 1)' succeeds
only if string is a null-terminated number (optionally preceded by some
whitespace characters). If there is some character appended after the number,
sscanf matches "%c", writes the character to the dummy variable and returns 2.
We check the return value for 1 and consequently reject numbers with some
garbage appended.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The dm-raid code currently fails to create a RAID array if any of the
superblocks cannot be read.  This was an oversight as there is already
code to handle this case if the values ('- -') were provided for the
failed array position.

With this patch, if a superblock cannot be read, the array position's
fields are initialized as though '- -' was set in the table.  That is,
the device is failed and the position should not be used, but if there
is sufficient redundancy, the array should still be activated.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Fix a harmless typo.

The root is a chunk of data that gets written to the superblock.  This
data is used to recreate the space map when opening a metadata area.
We have two space maps; one tracking space on the metadata device and
one of the data device.  Both of these use the same format for their
root, so this typo was harmless.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Now that the value_size is held within every node of the btrees we can
remove this argument from value_ptr().

For the last few months a BUG_ON has been checking this argument is
the same as that held in the node.  No issues were reported.  So this
is a safe change.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The map_context pointer should always be set. However, we have reports
that upon requeuing it is not set correctly.  So add set and clear
functions with a BUG_ON() to track the issue properly.
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Acked-by: NHannes Reinecke <hare@suse.de>
Tested-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NDave Wysochanski <dwysocha@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

As a precaution, set bi_end_io to NULL when failing to remap.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

free_devices in dm_table.c already uses list_for_each(), so we don't
need to check if the list is empty.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Remove documentation for unimplemented 'trim' message.

I'd planned a 'trim' target message for shrinking thin devices, but
this is better handled via the discard ioctl.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The dm raid module (using md) is becoming the preferred way of creating long-lived
mirrors through userspace LVM so remove the EXPERIMENTAL tag.
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Drop EXPERIMENTAL tag from dm-uevent.

It's not changed for a while and some userspace tools are relying upon it.
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

When we remove an entry from a node we sometimes rebalance with it's
two neighbours.  This wasn't being done correctly; in some cases
entries have to move all the way from the right neighbour to the left
neighbour, or vice versa.  This patch pretty much re-writes the
balancing code to fix it.

This code is barely used currently; only when you delete a thin
device, and then only if you have hundreds of them in the same pool.
Once we have discard support, which removes mappings, this will be used
much more heavily.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Avoid using the bi_next field for the holder of a cell when deferring
bios because a stacked device below might change it.  Store the
holder in a new field in struct cell instead.

When a cell is created, the bio that triggered creation (the holder) was
added to the same bio list as subsequent bios.  In some cases we pass
this holder bio directly to devices underneath.  If those devices use
the bi_next field there will be trouble...

This also simplifies some code that had to work out which bio was the
holder.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Always set io->error to -EIO when an error is detected in dm-crypt.

There were cases where an error code would be set only if we finish
processing the last sector. If there were other encryption operations in
flight, the error would be ignored and bio would be returned with
success as if no error happened.

This bug is present in kcryptd_crypt_write_convert, kcryptd_crypt_read_convert
and kcryptd_async_done.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Reviewed-by: NMilan Broz <mbroz@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch fixes a possible deadlock in dm-crypt's mempool use.

Currently, dm-crypt reserves a mempool of MIN_BIO_PAGES reserved pages.
It allocates first MIN_BIO_PAGES with non-failing allocation (the allocation
cannot fail and waits until the mempool is refilled). Further pages are
allocated with different gfp flags that allow failing.

Because allocations may be done in parallel, this code can deadlock. Example:
There are two processes, each tries to allocate MIN_BIO_PAGES and the processes
run simultaneously.
It may end up in a situation where each process allocates (MIN_BIO_PAGES / 2)
pages. The mempool is exhausted. Each process waits for more pages to be freed
to the mempool, which never happens.

To avoid this deadlock scenario, this patch changes the code so that only
the first page is allocated with non-failing gfp mask. Allocation of further
pages may fail.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NMilan Broz <mbroz@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Call the correct exit function on failure in dm_exception_store_init.
Signed-off-by: NAndrei Warkentin <andrey.warkentin@gmail.com>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Acked-by: NMilan Broz <mbroz@redhat.com>
Signed-off-by: NCong Wang <amwang@redhat.com>