Add support for QLogic HCAs which have hardware performance sampling
registers for PortSamplesControl and PortSamplesResult MADs.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The error codes for ib_post_send(), ib_post_recv(), and ib_post_srq_recv()
were inconsistent. Use EINVAL for too many SGEs and ENOMEM for too many
WRs.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The link state event calls were being generated when the SM told the SMA
to change link states. This works for IB_EVENT_PORT_ACTIVE but not if
the link goes down and stays down. The fix is to generate event calls
from the interrupt handler when the HW link state changes.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The LMC value was being saved by the SMA in two places. This patch
cleans it up so only one copy is kept.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Follow the IB spec. (C10-96) for post send which states that a flushed 
completion event should be generated for work requests posted when a QP
is in the error state.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The code to post UD sends tried to process work requests at the time
ib_post_send() is called without using a WQE queue.  This was fine as
long as HW resources were available for sending a packet.  This patch
changes UD to be handled more like RC and UC and shares more code.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Different processors have different ordering restrictions for write
combining.  By taking advantage of this, we can eliminate some write
barriers when writing to the send buffers.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Make some functions that are only used in a single .c file static.  In
addition to being a cleanup, this shrinks the generated code.  On x86_64:

add/remove: 1/3 grow/shrink: 2/1 up/down: 4777/-4956 (-179)
function                                     old     new   delta
handle_errors                                  -    3994   +3994
__verbs_timer                                 42     710    +668
ipath_do_ruc_send                           2131    2246    +115
ipath_no_bufs_available                      136       -    -136
ipath_disarm_senderrbufs                     639       -    -639
ipath_ib_timer                               658       -    -658
ipath_intr                                  5878    2355   -3523
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Clean up some code by removing support for some older pre-production
HTX InfiniPath cards.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>

Add a barrier to make sure the CPU doesn't reorder writes to memory,
since user programs can be polling on the head index update and the
entry should be written before that.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Now that it's June, it's about time to update
the copyright notices of files that have changed.
Signed-off-by: NJohn Gregor <john.gregor@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The code to copy data from the receive queue buffers to the IB SGEs
doesn't check the SGE length, only the memory region/page length when
copying data.  This could overwrite parts of the user's memory that
were not intended to be written.  It can only happen if multiple SGEs
are used to describe a receive buffer which almost never happens in
practice.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The send function is called when posting new send work requests.
There is no point in trying to send a packet if the QP is already
waiting for a HW send buffer so don't clear the busy bit until the
buffer available interrupt happens.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In ipath_query_device(), some of the struct ib_device_attr fields were
not being initialized.
Signed-off-by: NRobert Walsh <robert.walsh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Although our chip supports 4K MTUs, our driver doesn't yet support
this feature, so limit the maximum MTU to 2K until we get support for
4K MTUs implemented.
Signed-off-by: NRobert Walsh <robert.walsh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Once upon a time, GPIO interrupts were rare.  But then a chip bug in
the waldo series forced the use of a GPIO interrupt to signal packet
reception.  This greatly increased the frequency of GPIO interrupts
which have the gpio_mask bits set on the waldo chips.  Other bits in
the gpio_status register are used for I2C clock and data lines, these
bits are usually on.  An "unlikely" annotation leftover from the old
days was improperly applied to these bits, and an unnecessary chip
mmio read was being accessed in the interrupt fast path on waldo.

Remove the stagnant unlikely annotation in the interrupt handler and
keep a shadow copy of the gpio_mask register to avoid the slow mmio
read when testing for interruptable GPIO bits.
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API.  Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value.  Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.

We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity.  This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix the pending mmap code so it doesn't corrupt the list of pending
mmaps and crash the machine when pending mmaps are destroyed without
first being mapped.  Also, remove an unused variable, and use standard
kernel lists instead of our own homebrewed linked list implementation
to keep the pending mmap list.
Signed-off-by: NRobert Walsh <robert.walsh@qlogic.com>
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

All RDMA drivers except ehca set class_dev->dev to their dma_device
value (ehca leaves this unset).  dma_device is the only value that
makes any sense, so move this assignment to core/sysfs.c.  This reduce
the duplicated code in the rest of the drivers and gives ehca a nice
/sys/class/infiniband/ehcaX/device symlink.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch fixes a bug where multicast packets without a GRH were not
being dropped as per the IB spec.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds support for multiple RDMA reads and atomics to be sent
before an ACK is required to be seen by the requester.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch implements the interposing DMA mapping functions to allow
support for IOMMUs and remove the dependence on phys_to_virt() and
bus_to_virt().
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The array has only 5 entries, so [5] should have been [4].
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use.  This patch replaces those with a the init_utsname
helper.

Changes: Removed several uses of init_utsname().  Hope I picked all the
	right ones in net/ipv4/ipconfig.c.  These are now changed to
	utsname() (the per-process namespace utsname) in the previous
	patch (2/7)

[akpm@osdl.org: CIFS fix]
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This also entailed a little GPIO-interrupt general cleanup.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The sender requests an ACK every 1/2 MB to avoid retransmit timeouts that
were causing MVAPICH mod_bw to fail after a predictable number of sends.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Modifications to the existing rdma header files, core files, drivers,
and ulp files to support iWARP, including:
 - Hook iWARP CM into the build system and use it in rdma_cm.
 - Convert enum ib_node_type to enum rdma_node_type, which includes
   the possibility of RDMA_NODE_RNIC, and update everything for this.
Signed-off-by: NTom Tucker <tom@opengridcomputing.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This is useful for testing purposes.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When we first submitted a userspace subnet management agent, it was
rejected, so we left it out of the final driver submission.  This patch
removes a number of vestigial references to it.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A lot of ipath layer code was only called in one place. Now that the
ipath_core and ib_ipath drivers are merged, it's more sensible to simply
inline the simple stuff that the layer code was doing.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There is little point in keeping the two drivers separate, so we are
merging them.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Improve performance of userspace post receive, post SRQ receive, and
poll CQ operations for ipath by allowing userspace to directly mmap()
receive queues and completion queues.  This eliminates the copying
between userspace and the kernel in the data path.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ipath_skip_sge() doesn't exactly duplicate the side effects of
ipath_copy_sge() if num_sge > 1 since it doesn't decrement ss->num_sge.
This could result in the sg_list being accessed out of bounds.
Since ipath_skip_sge() is almost always called with num_sge == 1,
the original "optimization" is almost never used.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

I am still working on a proposal to remove the phys_to_virt() calls
in the ib_ipath driver.  In the mean time, this patch allows SRP
to work by fixing the R_Key check and conversion from IB address
to kernel virtual address.  It also returns the correct page size
for FMRs.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove ips namespace from infinipath drivers.  This renames ips_common.h to
ipath_common.h.  Definitions, data structures, etc.  that were not used by
kernel modules have moved to user-only headers.  All names including ips have
been renamed to ipath.  Some names have had an ipath prefix added.
Signed-off-by: NChristian Bell <christian.bell@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes some problems uncovered during IB compliance testing to
return the right values for error counters returned by the Performance Get
Counters packet.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>