Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wl1251 move accidently renamed wl1251_sdio and wl1251_spi
modules to just sdio and spi. Restore proper module names.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k aggregation code was already checking the rate control probe flag
to prevent starting an aggregate frame with a sampling rate. What was missing
was closing an aggregate before adding a probing frame to it.
Without that, rate control cannot have precise control over probing, which
delays using faster rates when the channel conditions improve.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If ah->curchan is uninitialized, the channel index is bogus, which leads
to invalid memory access when the cycle counters are updated.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We are not handling all divide by zero cases in paprd.
Add additional checks for divide by zero cases in papard.

This patch has fixes intended for kernel 2.6.36.

Cc: stable@kernel.org
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This updates the initvals for the AR9003 2.2 chipsets. The initvals
are the initial register values we use for our registers upon hardware
reset. This synchs up the initvals to match what our latest recommendation
from our systems engineering team.

The description of changes in this update:

        Improves ability to support very strong Rx conditions.
        Enhances DFS support for AP-mode.
        Improves performance of Tx carrier leak calibration.
        Adds support for Japan channel 14 Tx filtering requirements.
        Improves Tx power accuracy.

Impact:

        Update required to address degraded throughput at very short range.
        Update required for AP-mode DFS certification.
        Update required to comply to IEEE Tx carrier leak specification.
        May not meet expected +/- 2 dB Tx power accuracy without update.

The most important fix here would be the TX carrier leakage required
to comply with IEEE 802.11 specifications. The group of changes have
been tested all together in one release.

References:

	Osprey 2.2 header file ver #33

Checksums:

$ ./initvals -f ar9003-2p2
0x000000004a488fc7        ar9300_2p2_radio_postamble
0x0000000046cb1300        ar9300Modes_lowest_ob_db_tx_gain_table_2p2
0x00000000e912711f        ar9300Modes_fast_clock_2p2
0x0000000037ac0ee8        ar9300_2p2_radio_core
0x00000000047a7700        ar9300Common_rx_gain_table_merlin_2p2
0x0000000003f783bb        ar9300_2p2_mac_postamble
0x00000000301fc841        ar9300_2p2_soc_postamble
0x000000005ec8075f        ar9200_merlin_2p2_radio_core
0x0000000083372ffa        ar9300_2p2_baseband_postamble
0x00000000c4f59974        ar9300_2p2_baseband_core
0x00000000e20d2e72        ar9300Modes_high_power_tx_gain_table_2p2
0x000000007fd55c70        ar9300Modes_high_ob_db_tx_gain_table_2p2
0x0000000029495000        ar9300Common_rx_gain_table_2p2
0x0000000042cb1300        ar9300Modes_low_ob_db_tx_gain_table_2p2
0x00000000c4739cd6        ar9300_2p2_mac_core
0x000000003521a300        ar9300Common_wo_xlna_rx_gain_table_2p2
0x00000000a15ccf1b        ar9300_2p2_soc_preamble
0x0000000029734396        ar9300PciePhy_pll_on_clkreq_disable_L1_2p2
0x000000002d834396        ar9300PciePhy_clkreq_enable_L1_2p2
0x0000000029834396        ar9300PciePhy_clkreq_disable_L1_2p2

$ ./initvals -f ar9003-2p2 | sha1sum
0ceddb5cf66737610fb51f04cf3e9ff71870c7b4  -

Cc: stable@kernel.org
Cc: Yixiang Li <yixiang.li@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch 4f366c5d:

	wireless: only use alpha2 regulatory information from country IE

removed some complex intersection we were always doing between the AP's
country IE info and what we got from CRDA. When CRDA sent us back a
regulatory domain we would do some sanity checks on that regulatory
domain response we just got. Part of these sanity checks included
checking that we already had performed an intersection for the
request of NL80211_REGDOM_SET_BY_COUNTRY_IE type.

This mean that cfg80211 was only processing country IEs for cases
where we already had an intersection, but since we removed enforcing
this this is no longer required, we should just apply the country
IE country hint with the data received from CRDA.

This patch has fixes intended for kernels >= 2.6.36.

Cc: stable@kernel.org
Reported-by: NEaswar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch continues where the previous commit:
	"carl9170: fix async command buffer leak"
left off.

Similar to carl9170_reboot/carl9170_powersave, the
carl9170_async_regwrite* macros would leak the
temporary command buffer, if __carl9170_exec_cmd
fails to upload the command to the device.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I found this bug while poking around with a pure-gn AP.

Commit:
cfg80211/mac80211: Use more generic bitrate mask for rate control

Added some sanity checks to ensure that each tx rate index
is included in the configured mask and it would change any
rate indexes if it wasn't.

But, the current implementation doesn't take into account
that the invalid rate index "-1" has a special meaning
(= no further attempts) and it should not be "changed".
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If __carl9170_exec_cmd fails to upload an asynchronous
command to the device, the functions: carl9170_reboot
and carl9170_powersave will leak the temporary command
assembly buffer.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise, lockdep splats, at the least:

INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 0, comm: swapper Not tainted 2.6.36-rc8-wl+ #32
Call Trace:
 [<c075d940>] ? printk+0xf/0x17
 [<c045507a>] register_lock_class+0x5a/0x29e
 [<c0456af5>] __lock_acquire+0xa2/0xb8c
 [<c0455be2>] ? mark_lock+0x1e/0x1de
 [<c041a540>] ? acpi_get_override_irq+0x85/0x8c
 [<c0455536>] ? trace_hardirqs_off+0xb/0xd
 [<c0457639>] lock_acquire+0x5a/0x78
 [<f8126835>] ? ath5k_ani_calibration+0x24/0x52b [ath5k]
 [<c075f6ed>] _raw_spin_lock_bh+0x20/0x2f
 [<f8126835>] ? ath5k_ani_calibration+0x24/0x52b [ath5k]
 [<f8126835>] ath5k_ani_calibration+0x24/0x52b [ath5k]
 [<c0438f99>] ? tasklet_action+0x3b/0xc6
 [<f8123c2b>] ath5k_tasklet_ani+0x18/0x22 [ath5k]
 [<c0438fd1>] tasklet_action+0x73/0xc6
 [<c043945f>] __do_softirq+0x86/0x111
 [<c0439520>] do_softirq+0x36/0x5a
 [<c0439659>] irq_exit+0x35/0x69
 [<c0403fb9>] do_IRQ+0x86/0x9a
 [<c04034ee>] common_interrupt+0x2e/0x40
 [<c045007b>] ? do_adjtimex+0x223/0x55e
 [<c0408245>] ? mwait_idle+0x5c/0x6c
 [<c040227f>] cpu_idle+0x4e/0x6b
 [<c074b6e9>] rest_init+0x8d/0x92
 [<c09758ea>] start_kernel+0x320/0x325
 [<c09750d0>] i386_start_kernel+0xd0/0xd7
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise, lockdep splats, at the least:

INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2240, comm: ip Not tainted 2.6.36-rc8-wl+ #32
Call Trace:
 [<c075d940>] ? printk+0xf/0x17
 [<c045507a>] register_lock_class+0x5a/0x29e
 [<c0455be2>] ? mark_lock+0x1e/0x1de
 [<c0456af5>] __lock_acquire+0xa2/0xb8c
 [<c0455be2>] ? mark_lock+0x1e/0x1de
 [<c0457639>] lock_acquire+0x5a/0x78
 [<f8c5115b>] ? ath9k_config+0x274/0x3d8 [ath9k]
 [<c075f602>] _raw_spin_lock_irqsave+0x2f/0x3f
 [<f8c5115b>] ? ath9k_config+0x274/0x3d8 [ath9k]
 [<f8c5115b>] ath9k_config+0x274/0x3d8 [ath9k]
 [<f8c0ba2e>] ieee80211_hw_config+0x11b/0x125 [mac80211]
 [<f8c17edf>] ieee80211_do_open+0x3c5/0x466 [mac80211]
 [<f8c171d6>] ? ieee80211_check_concurrent_iface+0x21/0x13a [mac80211]
 [<f8c17fdb>] ieee80211_open+0x5b/0x5e [mac80211]
 [<c06ce76b>] __dev_open+0x80/0xae
 [<c06cc99b>] __dev_change_flags+0xa0/0x115
 [<c06ce6bf>] dev_change_flags+0x13/0x3f
 [<c06d7e78>] do_setlink+0x23a/0x51b
 [<c0455037>] ? register_lock_class+0x17/0x29e
 [<c06d847c>] rtnl_newlink+0x269/0x431
 [<c06d8291>] ? rtnl_newlink+0x7e/0x431
 [<c0455be2>] ? mark_lock+0x1e/0x1de
 [<c0455de9>] ? mark_held_locks+0x47/0x5f
 [<c075ebcf>] ? __mutex_lock_common+0x2bb/0x2d6
 [<c0456045>] ? trace_hardirqs_on_caller+0x104/0x125
 [<c075ebe0>] ? __mutex_lock_common+0x2cc/0x2d6
 [<c06d8213>] ? rtnl_newlink+0x0/0x431
 [<c06d79e2>] rtnetlink_rcv_msg+0x182/0x198
 [<c06d7860>] ? rtnetlink_rcv_msg+0x0/0x198
 [<c06e503c>] netlink_rcv_skb+0x30/0x77
 [<c06d7859>] rtnetlink_rcv+0x1b/0x22
 [<c06e4e77>] netlink_unicast+0xbe/0x119
 [<c06e5a15>] netlink_sendmsg+0x234/0x24c
 [<c06bf93a>] __sock_sendmsg+0x51/0x5a
 [<c06bfba4>] sock_sendmsg+0x93/0xa7
 [<c04968cf>] ? might_fault+0x47/0x81
 [<c0496904>] ? might_fault+0x7c/0x81
 [<c06c7904>] ? copy_from_user+0x8/0xa
 [<c06c7c2d>] ? verify_iovec+0x3e/0x6d
 [<c06bfd8c>] sys_sendmsg+0x149/0x193
 [<c0455037>] ? register_lock_class+0x17/0x29e
 [<c0455be2>] ? mark_lock+0x1e/0x1de
 [<c0498d7a>] ? __do_fault+0x1fc/0x3a5
 [<c048690a>] ? unlock_page+0x40/0x43
 [<c0498ef7>] ? __do_fault+0x379/0x3a5
 [<c04576dd>] ? lock_release_non_nested+0x86/0x1d8
 [<c04968cf>] ? might_fault+0x47/0x81
 [<c04968cf>] ? might_fault+0x47/0x81
 [<c06c148b>] sys_socketcall+0x15e/0x1a5
 [<c0402f1c>] sysenter_do_call+0x12/0x38
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iee80211_hw->restart_work is the only work which uses the system
workqueue.  Instead of calling flush_scheduled_work() during
iee80211_exit(), cancel the work during unregistration.

This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  Update broken web addresses in arch directory.
  Update broken web addresses in the kernel.
  Revert "drivers/usb: Remove unnecessary return's from void functions" for musb gadget
  Revert "Fix typo: configuation => configuration" partially
  ida: document IDA_BITMAP_LONGS calculation
  ext2: fix a typo on comment in ext2/inode.c
  drivers/scsi: Remove unnecessary casts of private_data
  drivers/s390: Remove unnecessary casts of private_data
  net/sunrpc/rpc_pipe.c: Remove unnecessary casts of private_data
  drivers/infiniband: Remove unnecessary casts of private_data
  drivers/gpu/drm: Remove unnecessary casts of private_data
  kernel/pm_qos_params.c: Remove unnecessary casts of private_data
  fs/ecryptfs: Remove unnecessary casts of private_data
  fs/seq_file.c: Remove unnecessary casts of private_data
  arm: uengine.c: remove C99 comments
  arm: scoop.c: remove C99 comments
  Fix typo configue => configure in comments
  Fix typo: configuation => configuration
  Fix typo interrest[ing|ed] => interest[ing|ed]
  Fix various typos of valid in comments
  ...

Fix up trivial conflicts in:
	drivers/char/ipmi/ipmi_si_intf.c
	drivers/usb/gadget/rndis.c
	net/irda/irnet/irnet_ppp.c

* 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/edac: (25 commits)
  i7300_edac: Properly initialize per-csrow memory size
  V4L/DVB: i7300_edac: better initialize page counts
  MAINTAINERS: Add maintainer for i7300-edac driver
  i7300-edac: CodingStyle cleanup
  i7300_edac: Improve comments
  i7300_edac: Cleanup: reorganize the file contents
  i7300_edac: Properly detect channel on CE errors
  i7300_edac: enrich FBD error info for corrected errors
  i7300_edac: enrich FBD error info for fatal errors
  i7300_edac: pre-allocate a buffer used to prepare err messages
  i7300_edac: Fix MTR x4/x8 detection logic
  i7300_edac: Make the debug messages coherent with the others
  i7300_edac: Cleanup: remove get_error_info logic
  i7300_edac: Add a code to cleanup error registers
  i7300_edac: Add support for reporting FBD errors
  i7300_edac: Properly detect the type of error correction
  i7300_edac: Detect if the device is on single mode
  i7300_edac: Adds detection for enhanced scrub mode on x8
  i7300_edac: Clear the error bit after reading
  i7300_edac: Add error detection code for global errors
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6: (27 commits)
  SLUB: Fix memory hotplug with !NUMA
  slub: Move functions to reduce #ifdefs
  slub: Enable sysfs support for !CONFIG_SLUB_DEBUG
  SLUB: Optimize slab_free() debug check
  slub: Move NUMA-related functions under CONFIG_NUMA
  slub: Add lock release annotation
  slub: Fix signedness warnings
  slub: extract common code to remove objects from partial list without locking
  SLUB: Pass active and inactive redzone flags instead of boolean to debug functions
  slub: reduce differences between SMP and NUMA
  Revert "Slub: UP bandaid"
  percpu: clear memory allocated with the km allocator
  percpu: use percpu allocator on UP too
  percpu: reduce PCPU_MIN_UNIT_SIZE to 32k
  vmalloc: pcpu_get/free_vm_areas() aren't needed on UP
  SLUB: Fix merged slab cache names
  Slub: UP bandaid
  slub: fix SLUB_RESILIENCY_TEST for dynamic kmalloc caches
  slub: Fix up missing kmalloc_cache -> kmem_cache_node case for memoryhotplug
  slub: Add dummy functions for the !SLUB_DEBUG case
  ...

* 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (321 commits)
  KVM: Drop CONFIG_DMAR dependency around kvm_iommu_map_pages
  KVM: Fix signature of kvm_iommu_map_pages stub
  KVM: MCE: Send SRAR SIGBUS directly
  KVM: MCE: Add MCG_SER_P into KVM_MCE_CAP_SUPPORTED
  KVM: fix typo in copyright notice
  KVM: Disable interrupts around get_kernel_ns()
  KVM: MMU: Avoid sign extension in mmu_alloc_direct_roots() pae root address
  KVM: MMU: move access code parsing to FNAME(walk_addr) function
  KVM: MMU: audit: check whether have unsync sps after root sync
  KVM: MMU: audit: introduce audit_printk to cleanup audit code
  KVM: MMU: audit: unregister audit tracepoints before module unloaded
  KVM: MMU: audit: fix vcpu's spte walking
  KVM: MMU: set access bit for direct mapping
  KVM: MMU: cleanup for error mask set while walk guest page table
  KVM: MMU: update 'root_hpa' out of loop in PAE shadow path
  KVM: x86 emulator: Eliminate compilation warning in x86_decode_insn()
  KVM: x86: Fix constant type in kvm_get_time_scale
  KVM: VMX: Add AX to list of registers clobbered by guest switch
  KVM guest: Move a printk that's using the clock before it's ready
  KVM: x86: TSC catchup mode
  ...

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-viapro: Don't log nacks
  i2c/pca954x: Remove __devinit and __devexit from probe and remove functions
  MAINTAINERS: Add maintainer for PCA9541 I2C bus master selector driver
  i2c/mux: Driver for PCA9541 I2C Master Selector
  i2c: Optimize function i2c_detect()
  i2c: Discard warning message on device instantiation from user-space
  i2c-amd8111: Add proper error handling
  i2c: Change to new flag variable
  i2c: Remove unneeded inclusions of <linux/i2c-id.h>
  i2c: Let i2c_parent_is_i2c_adapter return the parent adapter
  i2c: Simplify i2c_parent_is_i2c_adapter
  i2c-pca-platform: Change device name of request_irq
  i2c: Fix Kconfig dependencies

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (47 commits)
  HID: fix mismerge in hid-lg
  HID: hidraw: fix window in hidraw_release
  HID: hid-sony: override usbhid_output_raw_report for Sixaxis
  HID: add absolute axis resolution calculation
  HID: force feedback support for Logitech RumblePad gamepad
  HID: support STmicroelectronics and Sitronix with hid-stantuml driver
  HID: magicmouse: Adjust major / minor axes to scale
  HID: Fix for problems with eGalax/DWAV multi-touch-screen
  HID: waltop: add support for Waltop Slim Tablet 12.1 inch
  HID: add NOGET quirk for AXIS 295 Video Surveillance Joystick
  HID: usbhid: remove unused hiddev_driver
  HID: magicmouse: Use hid-input parsing rather than bypassing it
  HID: trivial formatting fix
  HID: Add support for Logitech Speed Force Wireless gaming wheel
  HID: don't Send Feature Reports on Interrupt Endpoint
  HID: 3m: Adjust major / minor axes to scale
  HID: 3m: Correct touchscreen emulation
  HID: 3m: Convert to MT slots
  HID: 3m: Output proper orientation range
  HID: 3m: Adjust to sequential MT HID protocol
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: Makefile - replace the use of <module>-objs with <module>-y
  crypto: hifn_795x - use cancel_delayed_work_sync()
  crypto: talitos - sparse check endian fixes
  crypto: talitos - fix checkpatch warning
  crypto: talitos - fix warning: 'alg' may be used uninitialized in this function
  crypto: cryptd - Adding the AEAD interface type support to cryptd
  crypto: n2_crypto - Niagara2 driver needs to depend upon CRYPTO_DES
  crypto: Kconfig - update broken web addresses
  crypto: omap-sham - Adjust DMA parameters
  crypto: fips - FIPS requires algorithm self-tests
  crypto: omap-aes - OMAP2/3 AES hw accelerator driver
  crypto: updates to enable omap aes
  padata: add missing __percpu markup in include/linux/padata.h
  MAINTAINERS: Add maintainer entries for padata/pcrypt

Conflicts:
	include/linux/percpu.h
	mm/percpu.c

Transactions not acked can happen every now and then, in particular
during device detection, and various transaction types can be used for
this purpose. So stop logging this event, except when debugging is
enabled. This is what other similar drivers (e.g. i2c-i801 or
i2c-piix4) do.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The underlying I2C adapter may or may not be present when this driver
gets initialized, and may disappear later, so there is no safe time at
which the probe and remove functions can be discarded.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch adds support for PCA9541, an I2C Bus Master Selector.
The driver is modeled as single channel I2C Multiplexer to be able to utilize
the I2C multiplexer framework.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NTom Grennan <tom.grennan@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

Check the class flags before allocating the temporary i2c_client
structure, to avoid allocating it when we don't need it.

Also optimize the inner loop a bit.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>

The "new_device" sysfs interface has been there for quite some time
now, nobody complained about it so it must be good enough. Time to
remove the warning and call it stable.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NMichael Lawnick <ml.lawnick@gmx.de>

The functions the functions amd_ec_wait_write and amd_ec_wait_read have an
unsigned return type, but return a negative constant to indicate an error
condition.

A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@exists@
identifier f;
constant C;
@@

 unsigned f(...)
 { <+...
*  return -C;
 ...+> }
// </smpl>

Fixing amd_ec_wait_write and amd_ec_wait_read leads to the need to adjust
the return type of the functions amd_ec_write and amd_ec_read, which are
the only functions that call amd_ec_wait_write and amd_ec_wait_read.
amd_ec_write and amd_ec_read, in turn, are only called from within the
function amd8111_access, which already returns a signed typed value.  Each
of the calls to amd_ec_write and amd_ec_read are updated using the
following semantic patch:

// <smpl>
@@
@@

+ status = amd_ec_write
- amd_ec_write
  (...);
+ if (status) return status;

@@
@@

+ status = amd_ec_read
- amd_ec_read
  (...);
+ if (status) return status;
// </smpl>

The patch also adds the declaration of the status variable.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: Nmatt mooney <mfm@muteddisk.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

These drivers don't use anything which is defined in <linux/i2c-id.h>.
This header file was never meant to be included directly anyway, and
will be deleted soon.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDave Airlie <airlied@linux.ie>
Cc: Hans Verkuil <hverkuil@xs4all.nl>

This makes the calling site's code clearer IMHO.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NMichael Lawnick <ml.lawnick@gmx.de>

Only i2c devices can have their type set to i2c_adapter_type, so
testing the bus type is redundant.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>

i2c->adap.name shouldn't be used in request_irq.
Instead the driver name "i2c-pca-platform" should be used.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
Signed-off-by: NJean Delvare <khali@linux-fr.org>

drivers/i2c/algos/Kconfig makes all the algorithms dependent on
!I2C_HELPER_AUTO, which triggers a Kconfig warning about broken
dependencies when some driver selects one of the algorithms. Ideally
we would make only the prompts dependent on !I2C_HELPER_AUTO, however
Kconfig doesn't currently support that. So we have to redefine the
symbols separately for the I2C_HELPER_AUTO=y case.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NMichal Marek <mmarek@suse.cz>

We also have to call kvm_iommu_map_pages for CONFIG_AMD_IOMMU. So drop
the dependency on Intel IOMMU, kvm_iommu_map_pages will be a nop anyway
if CONFIG_IOMMU_API is not defined.

KVM-Stable-Tag.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Breaks otherwise if CONFIG_IOMMU_API is not set.

KVM-Stable-Tag.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Originally, SRAR SIGBUS is sent to QEMU-KVM via touching the poisoned
page. But commit 96054569 prevents the
signal from being sent. So now the signal is sent via
force_sig_info_fault directly.

[marcelo: use send_sig_info instead]
Reported-by: NDean Nelson <dnelson@redhat.com>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Now we have MCG_SER_P (and corresponding SRAO/SRAR MCE) support in
kernel and QEMU-KVM, the MCG_SER_P should be added into
KVM_MCE_CAP_SUPPORTED to make all these code really works.
Reported-by: NDean Nelson <dnelson@redhat.com>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Fix typo in copyright notice.
Signed-off-by: NNicolas Kaiser <nikai@nikai.net>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

get_kernel_ns() wants preemption disabled.  It doesn't make a lot of sense
during the get/set ioctls (no way to make them non-racy) but the callee wants
it.
Signed-off-by: NAvi Kivity <avi@redhat.com>