Bump i40e to 1.2.6 and i40evf to 1.2.0 version.

Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add parsing and reporting of iSCSI capability for a given device or
function.

Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.

Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.

Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Disable firmware LLDP agent for NICs with firmware version lower than
v4.3. Added a message when driver disables the firmware LLDP agent on
such NICs.

Change-ID: Ia8abf89439c70cb50e23db82753d7d282265506b
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We should not blindly enable the PTP interrupt flags for all PFs. We
should only enable the PTP interrupt in PFs which have enabled
PTP.

Change-ID: I051a17cae4c199a2f3cf7852266e27eda6630525
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 1.2.5 and i40evf to 1.0.7.

Change-ID: I622556829056e3ed42d3b9d285fc5ffb693b21cc
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch creates a define for interrupt name string configuration that
is large enough to contain full bus/slot info, rather than just netdev->name.

Change-ID: Iaac0d23dfb8526defeed69d91cea85ed4a50ddb2
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We don't need to give up in the reset/rebuild process if the DCB setup failed,
so handle it here the same as in the probe setup.  Also adjust the log strings
a little to look less scary.

Change-ID: I57308d703047e61d3f1a5e471ea77be232444ca0
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where the /proc/interrupts descriptions
from the msix configuration were truncating the needed bus info,
making it hard to distinguish configuration from port to port.
This patch increases the string buffer size in order to allow the
full data to be displayed and sync's the text formatting of the misc
and fdir interrupt names

Change-ID: Ib01d6c61fb3f4ac70fbdf5bcc520b22638ea54b7
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure we only allow SR/IOV on the master PF of a port in multifunction
mode.  This should be the case anyway based on the num_vfs configured in
the NVM, but this will help make sure there's no question.  If we're not
in multifunction mode the partition_id will always be 1.

Change-ID: I8b2592366fe6782f15301bde2ebd1d4da240109d
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we were only checking if the link up state had changed,
and if it hadn't exiting the link event routine early. We should
also check if speed has changed, and if it has, stay and finish
processing the link event.

Change-ID: I9c8e0991b3f0279108a7858898c3c5ce0a9856b8
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

NPAR enabled partitions should warn the user when detected link speed is
less than 10Gpbs.

Change-ID: I7728bb8ce279bf0f4f755d78d7071074a4eb5f69
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current implementations all use dev_uc_add_excl() and such whose API
doesn't support vlans, so we can't make it with NICs HW for now.

Fixes: f6f6424b ('net: make vid as a parameter for ndo_fdb_add/ndo_fdb_del')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump version.

Change-ID: I4264e81dcfb57ec46a3ede54b0a6cb25b497d3cb
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is an order in which this should happen. It turns out that FW will
not let you change the Loopback setting of the VSI with update VSI prior
to the VEB creation.

Change-ID: I7614ddff8b4c37702930c02f16f8c346aaa64bd1
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

All VSIs on a VEB should either have loopback enabled or disabled, a
mixed mode is not supported for a VEB. Since our driver supports multiple
VSIs per PF that need to talk to each other make sure to enable Loopback
for the PF and FDIR VSI as well.

Also, we now have to explicitly enable Loopback mode otherwise we fail
VSI creation for VMDq and VF VSIs.

Change-ID: Ib68c3ea4aeb730ac9468f930610de456efbe5b20
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds additional text description for base pf0 and flow director
generated interrupts.  Without this patch, these interrupts are difficult
to distinguish per port on a multi-function device.

Change-ID: I4662e1b38840757765a3fe63d90219d28e76bfab
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This case statement is empty and the fall through just breaks out
so remove the break and let it fall through to break out.

Change-ID: I1b5ba9870d5245ca80bfca6e7f5f089e2eb8ccb0
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

So this can be reused for identification of other "items" as well.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Reviewed-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original FDB code submission wasn't correct and the code
wasn't enabled.  This removes some dead code (can use the common kernel
code for fdb_del and fdb_dump) and correctly enables the fdb_add
function pointer.

The fdb_add functionality is important to i40e because it is needed
for a workaround to allow bridges to work correctly on the i40e
hardware.
Reported-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we want the SW INT to go off as soon as possible, write the
extra bits that will turn off the ITR wait for the interrupt.

Change-ID: I6d5382ba60840fa32abb7dea17c839eb4b5f68f7
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Overloading the msg_size field in the arq_event_info struct is just a
bad idea. It leads to repeated bugs when the structure is used in a
loop, since the input value (buffer size) is overwritten by the output
value (actual message length).

Fix this by splitting the field into two and renaming to indicate the
actual function of each field.

Since the arq_event struct has now changed, we need to change the drivers
to support this. Note that we no longer need to initialize the buffer size
each time we go through a loop as this value is no longer destroyed by
arq processing.

In the process, we also fix a bug in i40evf_verify_api_ver where the
buffer size was not correctly reinitialized each time through the loop.

Change-ID: Ic7f9633cdd6f871f93e698dfb095e29c696f5581
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NAshish Shah <ashish.n.shah@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to DCBX configuration change if the VSI needs to use more than 1 TC;
it needs to disable the XPS maps that were set when operating in 1 TC mode.
Without disabling XPS the netdev layer will select queues based on those
settings and not use the TC queue mapping to make the queue selection.

This patch allows the driver to enable/disable the XPS based on the number
of TCs being enabled for the given VSI.

Change-ID: Idc4dec47a672d2a509f6d7fe11ed1ee65b4f0e08
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

FCoE VSI Tx queue disable times out when reconfiguring as a result of
DCB TC configuration change event.

The hardware allows us to skip disabling and enabling of Tx queues for
VSIs with single TC enabled. As FCoE VSI is configured to have only
single TC we skip it from disable/enable flow.

Change-ID: Ia73ff3df8785ba2aa3db91e6f2c9005e61ebaec2
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When DCB TC configuration changes the firmware suspends the port's Tx.
Now, as DCB TCs may have changed the PF driver tries to reconfigure the
TC configuration of the VSIs it manages. As part of this process it disables
the VSI queues but the Tx queue disable will not complete as the port's
Tx has been suspended. So, waiting for Tx queues to go to disable state
in this flow may lead to detection of Tx queue disable timeout errors.

Hence, this patch adds a new PF state so that if a port's Tx is in
suspended state the Tx queue disable flow would just put the request for
the queue to be disabled and return without waiting for the queue to be
actually disabled.
Once the VSI(s) TC reconfiguration has been done and driver has called
firmware AQC "Resume PF Traffic" the driver checks the Tx queues requested
to be disabled are actually disabled before re-enabling them again.

Change-ID: If3e03ce4813a4e342dbd5a1eb1d2861e952b7544
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the port TC configuration changes as a result of DCBx the driver
modifies the enabled TCs for the VEBs it manages. But, in the process
it did not update the enabled_tc value that it caches on a per VEB basis.

So, when the next reconfiguration event occurs where the number of TC
value is same as the value cached in enabled_tc for a given VEB; driver
does not modify it's TC configuration by calling appropriate AQ command
believing it is running with the same configuration as requested.
Now, as the VEB is not actually enabled for the TCs that are there any
TC configuration command for VSI attached to that VEB with TCs that are
not enabled for the VEB fails.

This patch fixes this issue.

Change-ID: Ife5694469b05494228e0d850429ea1734738cf29
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows i40e driver to query and use DCB configuration from
firmware when firmware DCBX agent is in CEE mode.

Change-ID: I30f92a67eb890f0f024f35339696e6e83d49a274
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When there are DCB configuration changes based on DCBX the firmware suspends
the port's Tx and generates an event to the PF. The PF is then responsible
to reconfigure the PF VSIs and switching topology as per the updated DCB
configuration and then resume the port's Tx by calling the "Resume Port Tx"
AQ command.

This patch adds this call to the flow that handles DCB re-configuration in
the PF.

Change-ID: I5b860ad48abfbf379b003143c4d3453e2ed5cc1c
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bumping minor version as this will be the second SW release and it
should be 1.

Change-ID: If0bd102095d2f059ae0c9b7f4ad625535ffbbdee
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ARQ events cause a service_task execution, and we do a link_status
check and full stats gathering for each service_task.  However, when
there are a lot of ARQ events, such as when doing an NVM update, we end up
doing 10's if not 100's of these per second, thereby heavily abusing the
PCI bus and especially the Firmware.  This patch adds a check to keep the
service_task from running these periodic tasks more than once per second,
while still allowing quick action to service the events.

Change-ID: Iec7670c37bfae9791c43fec26df48aea7f70b33e
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a few problems with our parsing of the MDET registers:
* Queue IDs are longer than 8 bits
* Queue IDs are absolute for the device and the base queue must be
  subtracted out.
* VF IDs are longer than 8 bits
* Use the MASK define to mask the event value, instead of the SHIFT
  define.

Change-ID: I3dc7237f480c02e1192a2a8ea782f8a02ab2a8b7
Reported-by: NMarc Neustadter <marc.neustadter@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We must insert the VSI ID in the QTX_CTL register when
configuring queues for VMDQ VSIs.

Change-ID: Iedfe36bd42ca0adc90a7cc2b7cf04795a98f4761
Reported-by: NMarc Neustadter <marc.neustadter@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check the debug module parameter earlier to be able to catch the early
configuration phase adminq messages.

Change-ID: Ic84fabd72393489bbf96042de770790a80fd8468
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Tweak and homogenize the error reporting for get_lump() resource
tracking errors.

Change-ID: I11330161cc6ad8d04371c499c63071c816171c3b
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When there are more cores than vectors available to the PF, scale back
the LAN msix usage to force queue/vector sharing and leave some vectors
for Flow Director, VMDq, etc.

Change-ID: Ie0317732eb85ad8d851d7da7d9af86b1bf8c21ad
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the interface is closed, but VFs exist, current code will spam all
the VFs with link messages every second. This is because the link event
code was looking at netif_carrier_ok() without checking to see if the
interface was actually open.

Refactor the logic to only check the carrier state if the interface is
actually open. This allows link changes to be reported correctly without
spamming the VFs.

Change-ID: If136e79bb3820d21ea4e39e332e8a9604efc2b2a
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When FD_SB/ATR are not enabled, do not allow flow director flush
and reinit.

Change-ID: Iafe261c1862992981615815551abd1ed9fada0a8
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We accidentally mask by the _SHIFT variable.  It means that "event" is
always zero.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump i40e version to 1.0.21.
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-By: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>